User guide

8
(1*/,6+ '(876&+ )5$1d$,6 ,7$/,$12 (63$f2/ 1('(5/$1'6 69(16.$(1*/,6+ '(876&+ )5$1d$,6 ,7$/,$12 (63$f2/ 1('(5/$1'6 69(16.$
6
7KHGHWHFWHGVSHDNHUVDUHGLVSOD\HG
Next
Retry
[ENT]:Next
Front Sp. :Yes
F.Height Sp. :No
Center Sp. :Yes
Surround Sp. :Yes
S.Back Sp. :Yes 2ch
Subwoofer :Yes
Step1:Speaker Detection
MultEQ
NOTE
If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.
7
8VH ui WR VHOHFW ³1H[W´ DQG WKHQ
SUHVV
ENTER
8
0RYHWKHVHWXSPLFURSKRQHWR
SRVLWLRQXVH
uiWRVHOHFW³1H[W´
DQGWKHQSUHVV
ENTER
The measurement of the second position
starts. Measurements can be made in up to
six positions.
Step2:Measurement
MultEQ
Please place microphone
Cancel
[ENT]:Next
Next
Calculate
2nd listening position.
at ear height at
If you want to omit measurements from the next
position onward, select “Calculate”.
(Go to
Step 3 Calculating
)
9
5HSHDWVWHSPHDVXULQJSRVLWLRQV
WR
When measurement of position 6 is
completed, a “All the measurements were
finished.” message is displayed.
Step2:Measurement
MultEQ
Retry
Cancel
[ENT]:Calculate
Calculate
All the measurements
were finished.
Set up speakers (Audyssey
®
Auto Setup)
Preparation
4
&RQQHFWWKHVHWXSPLFURSKRQHWRWKH
6(7830,&MDFNRIWKLVXQLW
3-1.Audyssey Auto Setup
MultEQ
at ear height at
Amp Assign: Normal
Front Sp. : A
F.Height : Measure
Start
Cancel
[ENT]:Select [RTN]:Back
Please place microphone
main listening position.
When the setup microphone is
connected, the following screen is
displayed.
The setting method for 7.1-channel playback using
the surround back speakers is described here.
For the method of setting up speakers other than
the 7.1-channel system, select “Amp Assign”
and perform steps 3 and 4 of “Set up speakers”
(vpage37).
5
8VH ui WR VHOHFW ³6WDUW´ DQG WKHQ
SUHVV
ENTER
When measuring begins, a test tone is
output from each speaker.
• Measurement requires several minutes.
If “Cancel” is selected
“Cancel Auto Setup?” is displayed on the TV
screen. If “Yes” is selected, “Audyssey Auto
Setup” closes.
NOTE
If “Caution” is displayed:
Go to “Error messages” (vpage 10), check
any related items, and perform the necessary
procedures.
If the problem is resolved, return and restart
“Audyssey Auto Setup”.
When performing Audyssey Auto
Setup over again
Press ui to select “Retry”, and then press
ENTER.
When measuring has stopped
Press ui to select “Cancel”, then press ENTER.
Press
o p to select “Yes”, then press ENTER.
Setting up the speakers again
Repeat the operation from step 4 of
Preparation
.
Remote control operation
buttons
Move the cursor
(Up/Down/Left/Right)
Confirm the setting Return to previous menu
Step 1
Speaker Detection
Step 2
Measurement
• In step 1, you will perform measurements at the main listening position.
• This step automatically checks the speaker configuration and speaker size, and calculates the channel
level, distance, and crossover frequency. It also corrects distortion in the listening area.
• In step 2, you will perform measurements at
multiple positions (two to six positions) other than
the main listening position.
• You can achieve a more effective correction of
distortion within the listening area by performing
measurements at multiple positions.