R Model SR-12S1 User Guide AV Surround Receiver
ENGLISH ITALIANO WARRANTY GARANZIA For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz.
CE MARKING English The SR-12S1 is in conformity with the EMC directive and low-voltage directive. Français Le SR-12S1 est conforme à la directive EMC et à la directive sur les basses tensions. Deutsch Das Modell SR-12S1 entspricht den EMC-Richtlinien und den Richtlinien für Niederspannungsgeräte. Italiano Il SR-12S1 è conforme alle direttive CEE ed a quelle per i bassi voltaggi. Nederlands De SR-12S1 voldoet aan de EMC eisen en de vereisten voor laag-voltage.
FOREWORD .................................................. 2 BASIC OPERATION (PLAY BACK) ............ 38 PRECAUTIONS ..................................................................................... 2 INSTALLATION ...................................................................................... 2 AMPLIFIER FEATURES ........................................................................ 3 AUDIO/VIDEO FEATURES ....................................................................
ENGLISH FOREWORD This section must be read before any connection is made to the mains supply. PRECAUTIONS The following precautions should be taken when operating the equipment. GENERAL PRECAUTIONS WARNINGS Do not expose the equipment to rain or moisture. Do not remove the cover from the equipment. Do not insert anything into the equipment through the ventilation holes. Do not handle the mains lead with wet hands. Do not cover the ventilation with any items such as tablecloths, newspapers, curtains, etc.
AMPLIFIER FEATURES • THX Ultra certified 7ch amplifiers have enough power for even the most difficult conditions found in large rooms. Enormous power reserves endow the system with substantial dynamic ability at high sound levels. 160 watts to each of the seven main channels the power amp section features an advanced, premium high- storage power supply capacitors, and fully discrete output stages housed in cast aluminum heat sinks .
ENGLISH DESCRIPTION THX® is an exclusive set of standards and technologies established by the world-renowned film production company, Lucasfilm Ltd. THX resulted from George Lucas’ desire to reproduce the movie soundtrack as faithfully as possible both in the movie theater and in the home theater. THX engineers developed patented technologies to accurately translate the sound from a movie theater environment into the home, correcting the tonal and spatial errors that occur.
Dolby Digital EX creates six full-bandwidth output channels from 5.1channel sources. This is done using a matrix decoder that derives three surround channels from the two in the original recording. For best results, Dolby Digital EX should be used with movies soundtracks recorded with Dolby Digital Surround EX. Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.
ENGLISH FRONT PANEL @0 q w @1 e r t y u i AV SURROUND RECEIVER SR-12S1 SURROUND VOLUME DOWN DOWN TUNER GYRO TUNING UP UP F/P AUTO TUNE T-MODE STAMDBY POEWER ON/OFF LD DVD DSS TV VCR1 VCR2/DVD-R CD TAPE AUX1 INPUT CD-R/MD PHONES DIGITAL AUX1 AUX2 7.
ENGLISH !3 MEMO (memory) button Press this button to enter the tuner preset memory numbers or station names. !4 S (Source)-DIRECT button When this button is pressed, the tone control circuitry is bypassed as well as Bass Management. Notes: • The surround mode is automatically switched to AUTO when the source direct function is turned on. • Additionally, Speaker Configurations are fixed automatically as follow.
ENGLISH FL DISPLAY as d DISP ST PRO LOGIC CINEMA MOVIE fgh ANALOG MUSIC MUSIC PRO LOGIC ATT DIGITAL AUTO TUNED AUTO SURR COPY DIRECT TEST THX SURR EX NIGHT DISC 6.1 MTX 6.1 SLEEP PEAK j k OTHER PCM L C R LFE DIGITAL SURROUND 96kHz SL OTHER PCM L S SR C R MULTI SLEEP M-SPKR ¡0 l ¡1 ¡2 ¡3 DISP ST PRO LOGIC CINEMA MOVIE ¡4 ¡5 ANALOG MUSIC MUSIC PRO LOGIC ATT DIGITAL AUTO TUNED DIRECT TEST AUTO SURR COPY THX SURR EX NIGHT DISC 6.1 MTX 6.
ENGLISH ¡2 AUTO.SURR (Auto Surround mode) indicator. This indicator illuminates to show that the AUTO SURROUND mode is in use. ¡3 THX SURR EX (THX Surround EX mode) indicator. When THX surround EX mode is selected , this indicator lights. ¡4 DTS-ES mode indicators (DISC6.1, MTX6.1) These indicators will show to DTS-ES decoding mode. ¡5 PEAK indicator This indicator is a monitor for an analog audio input signal.
ENGLISH REAR PANEL z x cv b n m , . + – DIGITAL-OUT OPT MONI. 2 PRE OUT MAIN IN 1 MULTI VIDEO OUT R MONI. 1 Y LD CB COAX GND 3 RS232C MULTI LEFT ROOM LEFT DVD CR DSS Y SW R 5 SL FRONT (AUX 2) TV CB SR SURR. SBL SURR. BACK IN CR FRONT MULTI RIGHT ROOM RIGHT SURR. BACK LEFT CENTER SURR. SURR. BACK LEFT MODEL NO.SR-12S1 C AM 4 MONITOR OUT + – FRONT GND L ANTENNA 2 Ú0 L DSS IN CD VCR2 / DVD - R IN RIGHT EXT.
Seven terminals are provided for the front left, front right, front center, surround left, surround right, surround back left, and surround back right speakers. ⁄0 Speaker outputs terminals (for Multi room) Two terminals are provided for the left and right speakers for Multiroom (2nd zone) Notes: • Connect the these jacks to the matching + or – terminals on your speakers.
ENGLISH REMOTE CONTROL UNIT RC3200 J ˆ button This chapter describes the functions which control the SR-12S1. Please look at the user guide of the RC3200 for operation instructions. K Serial port Press this button turns on the backlight to LCD display. To connect the RC3200 with your computer by attached serial cable for future upgrades. 12 L LCD touch screen ˆ 11 The LCD touch screen is divided into different sections: Here the date and time are displayed when you are operating your devices.
OPERATING DEVICES When the RC3200 is switched on for the first time or when it is reset, the Introduction screen appears for a few seconds. The RC3200 then automatically switches to the HOME screen that displays all available devices on your RC3200. You can return to this HOME screen from within other screens by pressing the HOME button. See “Activating the HOME screen” for more details. To operate devices on your RC3200 you have to switch to the HOME screen.
ENGLISH OPERATING AMP & TUNER To control the SR-12S1 by your RC3200, you have to select the device AMP or TUNER on HOME screen. INPUT SELECT 2 AMP PAGE 3/8 MAIN AMP PAGE 1/8 Tape, LD, AUX1, AUX2, VCR2, CD-R These buttons are used for selecting an input source. (see page 38) A/D button This button is used to select the Auto digital input, fixed digital input or analog input. (see page 44) Power on and off buttons These buttons are used to turn on or off SR-12S1.
MULTI ROOM AMP PAGE 5/8 AMP PAGE 8/8 AUTO, S-DIRECT, Mono, Stereo, M-Stereo (Multi channel stereo), Virtual, hall, matrix, Movie. These buttons are used to select surround mode. (see page 40, 41) On/Off These buttons are used to switch the unit to multi room mode. SURROUND MODE 2 Mute This button is used to mute the sound to multi room system temporarily. AMP PAGE 6/8 ENGLISH SURROUND MODE 1 Volume + and – These buttons are used to adjust the sound level to multiroom system.
ENGLISH TUNER PAGE 2/3 SHOW THE STATUS OF SR-12S1 ON THE LCD OF RC3200 RC3200 has 2way communication with SR-12S1, it shows some status screen for SR-12S1. 1/2 Status To show 1st page of status screen, press S button . Frequency Direct button This button is used to select the mode of frequency direct input. Stereo/Mono button This button is used to select the FM tuning mode, auto stereo or mono. RDS Display button Selects display mode function in RDS (Radio Data System) by this button.
ADJUSTING THE SETTINGS RC3200 starts up in Use mode. In this mode you operate your devices. For customizing the RC3200 (adjusting the settings, learning buttons or recording macros) you have to switch to the appropriate mode. The RC3200 settings can be adjusted in the Setup mode. Note • When switching between modes you will always return to the last active screen. The RC3200 can be put into 4 different modes. These modes are: Use mode: For operating your devices. See “Operating Devices”.
ENGLISH SECOND SETUP PAGE Tap the Revert button. A message screen appears to confirm or cancel the revert process. 2. Press OK or Cancel. • the date; • the time. Adjust the Date You can set the year, the month and the day in the date settings. Press “+” to increase or “–” to decrease the value for the year, month and day. 1. Tap “+” or “–” once to adjust the year, month and day one value up or down. 2. Press and hold “+” or “–” to adjust the values for the year and the month more rapidly.
If an IR code or a brand is not in the database, you can program RC3200 commands by transmitting IR signals from your existing remote controls to RC3200's learning eye. To do this, place RC3200 and the device's remote control on a flat surface, 2 to 10 cm apart. OK NO GOOD Top View DVD remote control unit Press and hold the button on the existing remote control you want to learn to the RC3200. When the RC3200 receives an IR code: • You hear a confirmation beep; • The label changes from Learning to OK.
ENGLISH 3. Tap Macro button. Macro screen appears. 4. Press and hold the Mode button for 3 seconds. The Mode screen appears. Tap Macro on the Mode screen. A message screen appears. RC3200 is now in Macro Mode. 5. 6. Tap Next. The device screen with the Macro label appears. 8. Tap Start. The HOME screen appears with the 'Recording' label at the top of the screen. The buttons you tap on this screen will not be recorded.
RC3200 EDIT If you want to personalize your RC3200 even more beyond its standard programming features, RC3200edit is the tool for you to use. You can find more information and updates of the software on http:// www.marantz.com. RC3200edit is the visual editor for creating and configuring RC3200 Configuration Files (NCF) on your computer. An NCF is a file that is used to define the RC3200 behaviour and look for the LCD touch screen. ENGLISH 13. Press Stop to stop recording. A message screen appears.
ENGLISH IMPORTANT NOTICES Take care not to scratch the touch screen Use your finger to tap the LCD touch screen or use plastic-tipped pens intended for use with touch screens. Never use an actual pen, pencil or other sharp object on the LCD touch screen. Protect RC3200 from extreme temperatures Keep RC3200 away from heaters and other heat sources. RC3200 is not waterproof RC3200 should not be exposed to rain or moisture. Do not store or use RC3200 in any location that is extremely damp or wet.
Front left and right speakers, and a center speaker Align the tweeters and mid-range drivers on the three front speakers on the same height as well as possible. SPEAKER PLACEMENT The ideal surround speaker system for this unit is 7-speaker systems, using front left and right speakers, a center speaker, surround left and right speakers, a surround back and a subwoofer. For best results we recommend that all front speakers be of the same type, with identical or similar driver units.
ENGLISH CONNECTING SPEAKERS FRONT LEFT RIGHT + – DIGITAL-OUT OPT MONI. 2 PRE OUT MAIN IN 1 L MULTI VIDEO OUT R MONI. 1 Y LD CB COAX GND 3 DVD CR DSS Y MONITOR OUT + – FRONT MULTI LEFT ROOM LEFT GND ANTENNA 2 CENTER FRONT MULTI RIGHT ROOM RIGHT SURR. BACK CENTER MODEL NO.SR-12S1 C AM LEFT 4 RS232C SW R 5 SL FRONT (AUX 2) SR SURR. SBL SURR. BACK L DSS IN CD TV CB IN CR VCR2 / DVD - R IN SURR. SURR. BACK LEFT RIGHT EXT.
ENGLISH CONNECTING THE AUDIO COMPONENTS OUT OUT IN OUT L L L L R R R R CD PLAYER SACD PLAYER L R L R R L R L TAPE DECK L R R L L R R L MD PLAYER OPT MONI. 2 PRE OUT MAIN IN FRONT LEFT GND 1 L MULTI VIDEO OUT MONI. 1 Y LD CB DVD CR DSS Y ANTENNA 2 R COAX GND 3 DIGITAL INPUT + – DIGITAL-OUT MONITOR OUT + – MULTI ROOM LEFT FRONT MULTI RIGHT ROOM RIGHT SURR. BACK CENTER MODEL NO.
ENGLISH CONNECTING VIDEO COMPONENTS CONNECT TO THE VIDEO JACKS DVD PLAYER AUDIO VIDEO OUT OUT AUDIO VIDEO OUT OUT SATTELITE TUNER L R L R LD PLAYER AUDIO VIDEO OUT OUT AUDIO VIDEO OUT OUT L R L R L R L R R L R L L R TV L R + – DIGITAL-OUT OPT MONI. 2 PRE OUT MAIN IN 1 L MONI. 1 MULTI VIDEO OUT R COAX R L GND 3 ROOM LEFT SW R 5 CB CR DSS Y L FRONT MULTI RIGHT ROOM RIGHT R L SURR. VCR2 / DVD - R IN DSS IN FRONT (AUX 2) SL LD DVD MONITOR OUT MODEL NO.
VIDEO IN S-VIDEO IN VIDEO IN ENGLISH CONNECT TO THE MONITOR AND VIDEO CAMERA S-VIDEO IN VP8100 VIDEO PROJECTOR MONITOR AUX1 INPUT S-VIDEO VIDEO L AUDIO R OPT MONI. 2 PRE OUT MAIN IN 1 MULTI VIDEO OUT MONI. 1 R 2 R COAX GND Y LD CB 3 MULTI LEFT ROOM LEFT C DVD SW CR DSS R 5 SL FRONT (AUX 2) SR SURR. SBL SURR. BACK FRONT MULTI RIGHT ROOM RIGHT SURR. BACK LEFT CENTER SURR. SURR. MODEL NO.
ENGLISH ADVANCED CONNECTING CONNECTING MULTI CHANNEL AUDIO SOURCE DIGITAL OUTPUT DIGITAL OUTPUT SATTELITE TUNER LD PLAYER + – DIGITAL-OUT OPT MONI. 2 PRE OUT MAIN IN L MULTI VIDEO OUT MONI. 1 Y LD CB ANTENNA 2 R COAX GND DIGITAL OUTPUT 3 MULTI LEFT ROOM LEFT DVD AM SW SL FRONT (AUX 2) SR SURR. SBL SURR. BACK FRONT MULTI RIGHT ROOM RIGHT SURR. CR DSS R 5 MONITOR OUT MODEL NO.
ENGLISH CONNECTING THE ANTENNA TERMINALS AM EXTERNAL ANNTENNA AM LOOP ANNTENNA FM EXTERNAL ANNTENNA FM FEEDER ANNTENNA + – DIGITAL-OUT OPT MONI. 2 PRE OUT MAIN IN 1 L MULTI VIDEO OUT MONI. 1 Y LD CB DVD CR ANTENNA 2 R COAX GND 3 MULTI LEFT ROOM LEFT C SW DSS R 5 SL FRONT (AUX 2) SR SURR. SBL SURR. BACK FRONT MULTI RIGHT ROOM RIGHT SURR. BACK LEFT CENTER SURR. SURR. MODEL NO.
ENGLISH CONNECTING REMOTE CONTROL JACKS + – DIGITAL-OUT OPT MONI. 2 PRE OUT MAIN IN 1 FRONT LEFT GND L MULTI VIDEO OUT MONI. 1 Y LD CB DVD CR DSS Y TV CB ANTENNA 2 FRONT R COAX GND 3 RIGHT MONITOR OUT MODEL NO.SR-12S1 C AM SURR. BACK LEFT 4 RS232C SW R 5 L VCR2 / DVD - R IN DSS IN FRONT (AUX 2) SL CD You can control other Marantz products through this unit with the remote controller by connecting REMOTE CONTROL terminals on each unit.
Select the AMP mode in remote commander. Press M (menu) button on the remote commander to display the “MAIN SETUP MENU” of the OSD menu system. There are 8 items in the MAIN SETUP MENU. Select a desired sub-menu with Up or Down cursor button, and press the OK button to entry. The display will change to selected sub-menu. You can lock the condition of setup to each sub-menu with Left or Right cursor buttons. Notes: If you desire to adjust any sub-menu, you need to set UNLOCKED.
ENGLISH INPUT SETUP (ASSIGNABLE DIGITAL INPUT) Nine digital inputs can be assigned as the desired source. Use this menu to select the digital input jack to be assigned to the input source. 1. Select “INPUT SETUP” in MAIN SETUP MENU with Up or Down cursor button, and press the OK button. 1 CD T APE CD - R I NPU T S E T UP : D6 - AT : ANA : D1 - AT TV DS S DVD V CR 1 V CR 2 LD AU X 1 MA I N 2. 3. 4.
SPEAKER DISTANCE (TIME ALIGNMENT) OSD menu system has an additional setup screen “THX AUDIO SETUP” on the 2nd page of SPEAKER SETUP. You can select setting of Boundary Gain Compensation and Advanced Speaker Array. Use this parameter to specify the distance of each speaker’s position from the listening position. The delay time is automatically calculated according to these distances. Begin by determining the ideal or most commonly used seating position in the room.
ENGLISH SPEAKERS LEVEL BASS PEAK LEVEL Here you will set the volume for each speaker so that they are all heard by the listener at the same level. With Dolby Digital and DTS , not only the LFE (Low Frequency Effects), but also the bass of all channels can be heard from the Subwoofer or Large-speakers. This procedure prevents these speakers from becoming too loud and creating an unbalanced sound. Since the sound is output at a loud volume, perform this operation carefully.
SURROUND 3 P RE F ERENCE T V - AU T O OS D I N F O D I G I T A L OU T S U BWOOF E R OU T MA I N 1. 2. ENGLISH PREFERENCE 4 : : : : S URR . MOD E : AU T O C I N EMA R E - EQ L FE LEVEL S URR L / R E F F E C T S URR B ACK E F F E C T C E N T ER E F F E C T S UB W E F F E C T D I S AB L E E NAB L E SOURC E THX EX I T Select “PREFERENCE” in MAIN SETUP MENU with Up or Down cursor button, and press the OK button. To select a desired content, press Up or Down cursor button.
ENGLISH PLII (PRO LOGIC II) MUSIC PARAMETER Pro Logic II-Music mode creates a rich and enveloping surround ambience from stereo sources such as CDs. In this mode, SR-12S1 includes three controls to fine-tune the soundfield as follow. 5 SRS DIALOG: Set the SRS DIALOG level between 0 and 6 level in 1 level interval with Left or Right cursor button. This can be popped out of the surround audio effects allowing the listener to easily discern what the actors say.
This sub-menu is to adjust the speaker levels for 7.1-channel input sources. Here you will adjust the volume for each channel so that they are all heard by the listener at the same level. 8 7 .1 CH I NPU T F RON T L C E N T ER F RON T R S URR . R S URR . B R S URR . B L S URR . L S UB W MA I N 1. 2. 3. 4. ENGLISH 7.1 CH INPUT LEVEL LEVEL : : : : : : : : 0 0 0 0 0 0 0 0 dB dB dB dB dB dB dB dB EX I T Select “7.1CH IN” in MAIN SETUP MENU with Up or Down cursor button, and press the OK button.
ENGLISH BASIC OPERATION (PLAY BACK) ADJUSTING THE MAIN VOLUME SELECTING AN INPUT SOURCE. Before you can listen to any input media, you must first select the input source at the SR-12S1. AV SURROUND RECEIVER SR-12S1 VOLUME DOWN UP VOL DOWN TUNER GYRO TUNING CH OK UP F/P AUTO TUNE T-MODE E.G. : DVD H Ex DVD DSS TV VCR1 VCR2/DVD-R CD TAPE DIGITAL AUX2 7.
OK VOL Dialogue Normalization (Dial Norm) is a feature of Dolby Digital. When playing back software which has been encoded in Dolby Digital, sometimes you may see a brief message in the front panel display which will read "Dial Norm X dB" (X being a numeric value). Dialogue Normalization serves to let you know if the source material has been recorded at a higher or lower level than usual.
ENGLISH SURROUND MODE The SR-12S1 is equipped with many surround modes. these are provided to reproduce a variety of surround sound effects, according to the content of the source to be played. The available surround modes may be restricted depending on the input signal and speaker setup. AUTO When this mode is selected, the receiver determines whether the digital input signal is Dolby Digital, Dolby Digital Surround EX, DTS, DTS-ES, HDCD or PCM-audio.
CAUTION This mode is used with source materials encoded in Dolby Digital and Dolby Surround. Dolby Pro Logic II brings the excitement of surround sound to any stereo mix, while making existing Dolby Surround mixes sound more like discrete 5.1 channels Surround sound. Dolby Pro Logic II has below 3 modes. Pro Logic II MOVIE provides 5.1 channel surround sound from Dolby Surround encoded stereo movie sound tracks. Pro Logic II MUSIC mode provides 5.
ENGLISH The relation between the selected surround mode and the input signal The surround mode is selected with the surround mode buttons on SR-12S1 or the remote control unit. However, the sound you hear is subject to the relationship between the selected surround mode and input signal. That relationship is as follows; Surround Mode Input Signal AUTO Dolby D Surr. EX DTS-ES Dolby D (5.1ch) DTS(5.1ch) Dolby D(2ch) Dolby D(2ch Surr) PCM(Audio) PCM 96kHz HDCD Analog S-DIRECT Dolby D Surr.
DOLBY (PL2-movie) (PL2-music) (PL2-PL) CSII music CSII cinema CSII mono STEREO Virtual Multi Ch. Stereo MOVIE HALL MATRIX Dolby D Surr. EX DTS-ES Dolby D (5.1ch) DTS(5.1ch) Dolby D(2ch) Dolby D(2ch Surr) PCM(Audio) PCM 96kHz HDCD Analog Dolby D Surr. EX DTS-ES Dolby D (5.1ch) DTS(5.1ch) Dolby D(2ch) Dolby D(2ch Surr) PCM(Audio) PCM 96kHz HDCD Analog Dolby D Surr. EX DTS-ES Dolby D (5.1ch) DTS(5.1ch) Dolby D(2ch) Dolby D(2ch Surr) PCM(Audio) PCM 96kHz HDCD Analog Dolby D Surr. EX DTS-ES Dolby D (5.
ENGLISH OTHER FUNCTION VIDEO ON/OFF TV AUTO ON/OFF FUNCTION This function allows the component connected to the TV-VIDEO in jack to control the power (ON/OFF) to the SR-12S1. AUTO POWER ON 1. When no video signals of a DVD, etc., are connected to the SR-12S1 or the DVD, etc., are connected directly to a TV, the unnecessary video circuit can be turned off by selecting the “VIDEO OFF” setting. To select video off condition, tap Video off on the remote.
RECORDING A DIGITAL SOURCE In normal operation, the audio or video source selected for listening through the SR-12S1 is sent to the record outputs. This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT , CD-R/MD OUT, VCR1 OUT, and VCR2/DVD-R OUT in the record mode.
ENGLISH 7.1 CH INPUT. The SR-12S1 is equipped for future expansion through the use of Multi channel Super Audio CD or DVD-Audio player. This is selected, the input signals connected to the FL(front left), FR(front right), CENTER, SL (surround left), SR (surround right), SBL (surround back left) and SBR (surround back right) channels of the 7.1 CH.
DIRECT FREQUENCY CALL LISTENING TO THE TUNER 2. Frequency scan step for AM is selectable. Default setup is 10 kHz step, if your country’s standard is 9 kHz step, touch “AM” button on the remote more than 6 seconds. Scan step will change. ENGLISH BASIC OPERATION (TUNER) 3. 1. Note: • Preset memory for the tuner will clear by changing this setup. 1. AUTO TUNING 1. 3. 2. 3. 2. AV SURROUND RECEIVER SR-12S1 4.
ENGLISH 3. Each time the tuner finds a station, scanning will pause and the station will be played for five seconds. During this time, the following operations are possible. 1) The band can be changed by TUNER button . 2) The tuning mode can be changed by T-MODE button.
RDS OPERATION AV SURROUND RECEIVER SR-12S1 SURROUND DOWN DOWN TUNER GYRO TUNING Now in use in many countries, RDS (Radio Data System) is a description of the station's programming hidden space in the FM signal. SR-12S1 is equipped with RDS to assist in the selection of FM stations using station and network names, rather than broadcast frequencies. Additional RDS functions include the ability to search for program types.
ENGLISH PTY AUTO SEARCH Your receiver is equipped to automatically search for stations transmitting any of 29 different program types. To search for a PTY, follow these steps: 2. 2. AV SURROUND RECEIVER SR-12S1 DOWN TUNER GYRO TUNING UP F/P AUTO TUNE LD DVD DSS TV VCR1 VCR2/DVD-R CD AUX1 AUX2 7.1CH INPUT ATT S-DIRECT MEMO CLEAR TAPE DIGITAL 1. 2. 3. 4. MULTI SPKR MULTI ROOM S-VID 1. 3. 4. Tap PTY button in screen of 2/3 TUNER .
3. The Multi Room system is a function which allows you to listen to the same or a different source in a room other than the room in which the SR-12S1 is located. To use this function, a multi room remote unit and remote control signal receiver available from your Marantz dealer are necessary. The operations possible with the multi room function are explained briefly below. For details, refer to the instruction manual supplied with the multi room remote control unit and receiver. 4.
ENGLISH TROUBLESHOOTING In case of trouble, check the following before calling for service: 1. Are the connections made properly ? 2. Are you operating the unit properly following user’s guide ? 3. Are the power amplifiers and speaker working properly ? CAUSE SYMPTOM SR-12S1 cannot be turned up. If the unit does not operate properly, check items shown in the following table.
HOW TO RESET THE UNIT AV SURROUND RECEIVER SR-12S1 SURROUND VOLUME DOWN DOWN TUNER GYRO TUNING ENGLISH GENERAL MALFUNCTION If the equipment malfunctions, this may be because an electrostatic discharge or AC line interference has corrupted the information in the equipment memory circuits.
ENGLISH TECHNICAL SPECIFICATIONS FM TUNER SECTION Frequency Range .................................... 87.5 - 108.0 MHz Usable Sensitivity ................................ IHF 1.8 µV/16.4 dBf Signal to Noise Ratio ....................... Mono/Stereo 76/72 dB Distortion ........................................ Mono/Stereo 0.2/0.3 % Stereo Separation ........................................... 1 kHz 45 dB Alternate Channel Selectivity ................... ± 300 kHz 60 dB Image Rejection ......................
www.marantz.com You can find your nearest authorized distributor or dealer on our website. JAPAN Marantz Japan, Inc. 35-1 Sagami Ohno 7-Chome, Sagamihara-shi, Kanagawa 228-8505, Japan U.S.A. Marantz America, Inc. 1100 Maplewood Drive, Itasca, IL 60143, U.S.A. EUROPE Marantz Europe B.V. P.O. Box 8744, 5605 LS Eindhoven, The Netherlands Manufactured under license from Dolby Laboratories. “Dolby”, “AC-3”, “Pro Logic” and the double-D symbol are trademarks of Dolby Laboratories.
