R Model SR7200 User Guide AV Surround Receiver
ENGLISH ITALIANO WARRANTY GARANZIA For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz.
CE MARKING English The SR7200 is in conformity with the EMC directive and low-voltage directive. Français Le SR7200 est conforme à la directive EMC et à la directive sur les basses tensions. Deutsch Das Modell SR7200 entspricht den EMC-Richtlinien und den Richtlinien für Niederspannungsgeräte. Nederlands De SR7200 voldoet aan de EMC eisen en de vereisten voor laag-voltage. Español El SR7200 está de acuerdo con las normas EMC y las relacionadas con baja tensión.
a s d f g h j kl ¡0 ¡1 ¡2 ¡3 Y L DIGITAL IN / OUT R L R MULTI ROOM L R R OUT MULTI ROOM CD L Cb R L OUT OUT FRONT PRE OUT CDR / MD FRONT CDR / MD MONITOR MONI TOR TAPE VCR1 OUT VCR1 OUT Y Cr FRONT MONITOR DIG - 5 IN ANTENNA CTRL 1 OUT SURR. SPEAKER IMPEDANCE FRONT A OR B, CENTER, SURROUND, SURR. BACK : 6 - 16 OHMS FRONT A AND B : 12 - 16 OHMS DIG - 4 IN CENTER SURR. CENTER SUB WOOFER SUB WOOFER CENTER SURR.
FOREWORD .................................................................................................................................................................... 2 PRECAUTIONS ........................................................................................................................................................................................................ 2 INTRODUCTION ...........................................................................................................
ENGLISH FOREWORD PRECAUTIONS This section must be read before any connection is made to the mains supply. The following precautions should be taken when operating the equipment.
FEATURES Thank you for purchasing the Marantz SR7200 DTS/Dolby Digital Surround receiver. This remarkable component has been engineered to provide you with many years of home theater enjoyment. Please take a few minutes to read this manual thoroughly before you connect and operate the SR7200. As there are a number of connection and configurations options, you are encouraged to discuss your own particular home theater setup with your Marantz A/V specialist dealer.
ENGLISH i S. ( Source) DIRECT button FRONT PANEL FEATURES (SEE PAGE iii.) When this button is pressed, the tone control circuit is bypassed as well as Bass Management. Notes: The surround mode is automatically switched to AUTO when the source direct function is turned on. Additionally, Speaker Configurations are fixed automatically as follow.
Connect to these outputs to the component video inputs of a video projector or monitor. When a source connected to one of the two component video inputs is selected the signal will be sent to these jacks. All connections to the rear panel should be made with the entire system powered off. To avoid errors, it is advisable to connect one cable at a time between the various components. ¡2 SPEAKER SYSTEMS A terminals FRONT Left & Right speakers output terminals Connect to the front left & right speakers.
ENGLISH ™1 Video inputs Ex: TV, DVD, VCR1, and DSS/VCR2 Connect each input to the video outputs of your video source equipment. ™2 S-video inputs Ex: TV,DVD, VCR1,and DSS/VCR2 Connect each input to the S-video outputs of your video source equipment. ™3 COMPONENT VIDEO inputs Ex: DVD,and DSS/VCR2 Connect to the Y/Cr/Cb component video outputs of each your video product to these jacks. ™4 AC OUTLET Connect the power cables of components such as a DVD or CD player to this outlet.
REMOTE CONTROL BUS CONNECTIONS ENGLISH This unit is equipped with a remote control function. By connecting this unit’s remote control jacks to a Marantz CD player or tape deck equipped with remote control (RC-5) jacks, it allows system remote control to operate. Connect REMOTE CONTROL OUT jack of SR7200 to REMOTE CONT. IN of other Marantz equipment, i.e. CD player or tape deck, by using an RCA pin cable.
ENGLISH REMOTE CONTROL UNIT RC7200SR OPERATION OF REMOTE CONTROL UNIT This chapter describes the functions which need to control the SR7200. See page 18 and following pages to refer other function of the RC7200SR. 1. Remote control The distance between the transmitter of the remote control unit and the IR SENSOR of the SR7200 should be less than about 5 meters.
ENGLISH SET-UP After all components are connected, initial setup must be performed. ON SCREEN DISPLAY MENU SYSTEM The SR7200 incorporates an on-screen menu system, which makes various operations possible by using the cursor (<, >, ^, v) and OK buttons on the remote controller. The settings made with these buttons are also shown in the on-screen display.
SYSTEM SETUP 2/3 (SELECTING THE DIGITAL INPUT) ENGLISH OSD MAIN MENU 1. 2. Five digital inputs can be assigned for the desired source. Use this menu to determine which source is connected to which input. Press the AMP button ,. Press OK button ⁄0 to display the “MAIN MENU” of the on-screen display menu. Choose a desired item in the contents with ^ or v button, and press the OK button to select. Display will change to menu for each item.
Select the type of front speakers with < or > button. Select the type of center speaker with < or > button. Select the type of surround speakers with < or > button. Select the surround center speaker YES or NO with < or > button. SUBWOOFER: Select the subwoofer speaker YES or NO with < or > button. The home theater system you already have installed should function provided that there are left, center and right front speakers, left and right rear/surround speakers and a subwoofer.
ENGLISH SURROUND MODE MULTI ROOM SETUP SOURCE DIRECT : Switch the source direct ON or OFF with < or > button. This bypasses the surround processing and crossover for the main speakers (front left and right will be full range and the subwoofer will be ON) Note: Surround mode cannot be changed in Source Direct mode. SURR-MODE : Select the surround mode with < or > button. NIGHT MODE : Switch the NIGHT MODE ON or OFF with < or > button.
3. Recalling a Preset Station 1. Press the F/P button !6 to change the display to preset. 2. Select the desired preset station by pressing TUNING/PRESET or button !5 on the front panel or press CH or CH button ⁄2 on the remote. LISTENING TO THE TUNER MANUAL TUNING 1. 2. 3. 4. 5. To select the tuner as the source, press the TUNER button t on the front panel or press the TUNER button , on the remote control unit.
ENGLISH STATION NAME PRESET (on PRESET display mode) PROGRAMME TYPE (PTY) DISPLAY The station name preset function allows the name of each preset channel to be entered using alphanumeric characters. The Station Name button is valid only in the tuner mode. Before station name preset operation, store stations with the preset memory operation. 1. Press the MEMORY button !4 on the front panel or MEMO button ⁄6 on the remote for more than 3 seconds. 2.
OTHER FUNCTIONS NORMAL PLAYBACK SETTING THE SLEEP TIMER 1. 2. 3. 4. Press the POWER ON button on the remote. Press the FUNCTION SELECTOR button t on the front panel or press the FUNCTION button , on the remote unit to select an input source. Turn the SURROUND MODE SELECTOR knob e on the front panel or Surround mode buttons ⁄7 in the AMP MODE on the remote unit to select the desired surround mode. Adjust the volume level using the VOLUME knob r on the front panel or press the VOL / button .
ENGLISH MULTI ROOM SELECTOR ON SCREEN DISPLAY INFOMATION The Multi Room Selector is a function which allows you to listen to the same or a different source in a room other than the room in which the SR7200 is located. To use this function, a multi room remote unit and remote control signal receiver available from your Marantz dealer are necessary. The operations possible with the multi room function are explained briefly below.
5.SLEEP TIMER When a function selector button or surround mode button is pressed VIDEO: Displays the current video source. When TV, DSS, DVD, VCR1 or AUX is selected with the function selector, both AUDIO and VIDEO shows the same name. AUDIO: Displays the current analog audio input source. DIGITAL: Displays the current digital input source.
ENGLISH REMOTE CONTROL UNIT RC7200SR NAMES OF PARTS & FUNCTIONS MAIN FEATURES & FUNCTIONS c POWER • PROGRAMMABLE LEARNING FUNCTION ON Can easily be programmed to learn the codes for almost any other infrared-based remote, allowing the remote control functions for many different components to be consolidated conveniently in a single unit.
⁄8 Infrared Transmitter/Receiver Window Used to execute a function selected with the Jog Dial n. There are 2 ENT buttons, one on each side, so that the remote controller can be used just as easily with either hand. The characters on the display can also be programmed. Used to transmit remote control signals based on beams of infrared light to system components.
BASIC OPERATION Indicates when the < • 3 (CURSOR/TRANSPORT CONTROL switching) ⁄1 is in a transport control mode such as PLAY, STOP, etc. • If the LCD flickers when a button is pressed in order to transmit a command or when in the LEARN mode, the transmission or learning is not possible. In such a case, please replace the batteries. • This remote controller uses non-volatile memory, so that learned codes and macros will be preserved even if the batteries are removed.
DVD CD DSS LD CLEAR VCR AUX TUNER TAPE AMP MEMO DTS GUIDE MUTE CS5.1 6.1 Press the PLAY button ⁄0 (3 OK). The LEARN indicator changes from blinking to continuously lit. CH OK CD 5. Let’s use the example of setting as the TITLE code for the DVD player. 1. Use a ballpoint pen or other sharp point to press the MODE button z until the LEARN indicator is displayed and starts to blink. 2.
REWRITING NAMES 7. ENGLISH This remote controller allows the names accessible by Jog Dial control n to be rewritten with new ones of your choosing. • Rewriting of names is performed for each individual function. • Let’s use a DVD player as an example to show how to change the ’s “OSD” to “F-OSD”. 1. 2. Use a ballpoint pen or other sharp point to press the MODE button z to switch the remote controller to the NAME mode. The NAME indicator blinks. Press the DVD Function button ,.
Erasing Jog Dial Codes To clear all codes and names previously set for each of the functions (DVD, TV, etc.). 1) Press the function you want to erase. 2) Hold down the CLEAR button ⁄5 and press both ENT buttons m at the same time. LCD b will display CLR?. ENT 5. ENT CH VOL OK DVD CD LD CLEAR VCR AUX TUNER TAPE AMP GUIDE MUTE DTS CS5.1 6.1 MEMO AUTO If you wish to continue the clearing operation, press the OK Cursor button ⁄0.
3. ENGLISH Press the buttons for the operations you wish to program as a macro in the sequence you want the macro to program them. The name of the button pressed appears on LCD a. The number of steps in the macro is displayed on LCD c and this number increases by 1 with each button pressed. For example, press DVD, PLAY. Each function button can be programmed to perform up to 10 steps in sequence.
Example 2 Turn the main amplifier ON → Change the amplifier’s input source to DVD → Set the Surround mode to DOLBY → Switch the TV to video input → Set the DVD player to PLAY Example 1 Change the input source for the amplifier to CD and play the 3rd track on a CD in the CD player. 1. 1. Use a ballpoint pen or other sharp point to press the MACRO button x, then press the CD Function button ,. CD-M is displayed on the LCD. Use a ballpoint pen or other sharp point to press the MACRO button x.
ENGLISH OTHER FUNCTIONS BATTERY LIFE LUMINOUS BUTTONS • New batteries will last about 4 months assuming an average of 30 uses per day. The buttons on this remote controller are designed to remain luminous in dim lighting conditions. If the buttons are no longer luminous when the remote controller is used in low light, recharge them by placing it near a fluorescent or other light source for a sufficient amount of time. This should return the buttons to their luminous condition.
Function Jog Dial command VCR 1 REC 2 SLCT 3 2XPLY 4 SLOW 5 STIL 6 OTR 7 AUDIO 8 SKIP 9 VIS+ 0 VISDSS/V2 1 DISP 2 PREV 3 SELCT 4 AUDIO 5 FAV 6 ALT 7 FTCH 8ANT 9 REC 0 OTR AUX 1 No 2 No 3 No 4 No 5 No 6 No 7 No 8 No 9 No 0 No DVD 1 OSD 2 TITLE 3 ZOOM 4 MENU 5 10+ 6 SETUP 7 ANGLE 8 SUB-T 9 RESUM 0 AUDIO Each of the 10 Jog Dial commands on the LCD has 5 character labels attached for pre-programmed remote commands.
ENGLISH SURROUND MODES The SR7200 incorporates digital signal processors (DSP) which can reproduce various surround effects you experience in concert halls and movie theaters, etc. These Surround Modes, are provided to reproduce a variety of surround sound effects, according to the content of the source to be played. FEATURES Surroud mode 1. AUTO When this mode is selected, the receiver determines whether the digital input signal is Dolby Digital, PCM-audio or DTS.
The surround mode is selected with the surround mode selector knob of the SR7200 or the remote control unit. However, the sound from the speakers depend upon the relationship between the selected surround mode and the input signal. They are as follows; Surround Input Signal Mode Auto Dolby Digital (5.1ch) Dolby Digital (2ch) Dolby Digital (2ch:Lt/Rt) 96kHz PCM PCM(Audio) Analog DTS (5.1ch) Stereo Dolby Digital (5.1ch) Dolby Digital (2ch) Dolby Digital (2ch:Lt/Rt) 96kHz PCM PCM(Audio) Analog DTS (5.
ENGLISH TROUBLESHOOTING If the unit does not operate properly, check items shown in the following table. If your trouble cannot be recovered with the remedy actions listed in the following table, malfunction of the internal circuitry is suspected; immediately unplug the power cable and contact your dealer, nearest Marantz distributor or the Marantz Service Center in your country. In case of trouble, check the following before calling for service: 1. Are the connections made properly ? 2.
ENGLISH GENERAL MALFUNCTION If the equipment malfunctions, this may be because an electrostatic discharge or AC line interference has corrupted the information in the equipment memory circuits.
TECHNICAL SPECIFICATIONS FM TUNER SECTION Frequency Range ................................................................................................................................................. 87.5 - 108.0 MHz Usable Sensitivity ............................................................................................................................................. IHF 1.8 µV/16.4 dBf Signal to Noise Ratio ........................................................................................
COUNTRY ALGERIE ARMENIA AUSTRALIA AUSTRIA BAHREIN BANGLADESH BELGIUM BULGARIA CANADA CHINA CYPRUS CZECH REPUBLIC DENMARK DUBAI EGYPT ESTONIA F.Y.R.O.M. FINLAND FRANCE GERMANY GREECE HEADQUARTERS EUROPE: HONG KONG HUNGARY ICELAND INDIA IRAN IRELAND ISRAEL ITALY IVORY COAST JAPAN KOREA KUWAIT LATVIA LEBANON LITHUANIA MALAYSIA MALTA MAURITIUS MILITARY MARKET EUROPE NETHERLANDS NEW ZEALAND NORWAY OMAN POLAND PORTUGAL PROFESSIONAL EUROPE PROFESSIONAL U.S.A.
