. Model PM-KI RUBY Owner’s Manual Integrated Amplifier You can print more than one page of a PDF onto a single sheet of paper.
Contents Accessories ................................................................................... 2 About the remote control .............................................................. 2 Inserting the batteries ................................................................... 2 Operating range of the remote control unit .................................... 2 Features .......................................................................................... 3 High quality sound ..................
ENGLISH About the remote control Inserting the batteries 1 arrow and remove it. Remove the rear lid in the direction of the Accessories Operating range of the remote control unit Point the remote control unit at the remote sensor when operating it. Overview Thank you for purchasing this Marantz product. To ensure proper operation, please read this owner’s manual carefully before using the product. After reading this manual, be sure to keep it for future reference.
ENGLISH Features High quality sound 0 0 0 0 0 0 0 0 3 HDAM®SA3 Module The HDAM® SA3 is a key amplifier module for current feedback amplifiers. It is installed in the voltage to current converter, the most crucial component, to improve the stability of the circuit and provide high-speed sound. Linear Control Volume The HDAM®SA3 is combined with a JRC volume IC to achieve low distortion and high S/N. A range of volumes between 0 and -99.5 dB can be smoothly controlled in ±0.5 dB steps.
ENGLISH Part names and functions Front panel w e r t y w Overview q u Connections . B Illumination lamp The illumination lamp lights (blue). C Display This displays various pieces of information. E STANDBY indicator This is lit as follows according to the power status: 0 Power on : Off 0 Standby : Red 0 Power off : Off I Power operation button (X) This turns the power on/off. (v p. 16) J Remote control sensor This receives signals from the remote control unit. (v p.
ENGLISH Rear panel q w CD LINE-1 LINE-2 e r t SPEAKERS RECORDER-1 RECORDERRECORDERRECORDER-2 RECORDERRECORDER-1 RECORDERRECORDER-2 IN OUT y STEREO BI-AMP REMOTE CONTROL IN AUDIO IN AUDIO OUT OUT AMP MODE ID F.C.B.S. POWER AMP IN AC IN SIGNAL GND PHONO . AUDIO IN u A Analog audio input connectors (AUDIO IN) Connecting to a device with analog audio output connectors. 0 “Connecting a playback device” (v p. 9) 0 “Connecting a recording device” (v p.
ENGLISH Remote control unit n Operating this unit To operate amplifier, press REMOTE MODE AMP button to switch the remote control to the amplifier operation mode. w e t y u Q0 r Q1 D Input source select buttons (INPUT df) This selects the input source. (v p. 16) E Power operation button (X AMP) This turns the power on/off (standby). (v p. 16) F Remote mode select button (REMOTE MODE AMP) This switches the remote control to amplifier control mode. G ENTER button This determines the selection.
ENGLISH n CD player operations To operate a Marantz CD player, press the REMOTE MODE CD button to switch the remote control to the CD player operation mode.
ENGLISH Connections 8 Connecting a playback device 9 Connecting a recording device 9 0 Connecting multiple PM-KI RUBY units (F.C.B.S. connection) 10 0 Connecting a pre-amplifier 14 Connecting devices with remote control connectors 15 Connecting the power cord 15 0 Do not plug in the power cord until all connections have been completed. Do not bundle power cords together with connection cables. Doing so can result in humming or noise.
ENGLISH Speaker connection CD LINE-1 LINE-2 SPEAKERS RECORDER-1 RECORDERRECORDERRECORDER-2 RECORDERRECORDER-1 RECORDERRECORDER-2 IN OUT Connecting a recording device Connecting a playback device STEREO BI-AMP REMOTE CONTROL IN AUDIO IN AUDIO OUT POWER AMP IN OUT AMP MODE ID F.C.B.S. AC IN SIGNAL GND PHONO AUDIO IN SPEAKERS (L) w (R) q w You can connect turntables, tuners, CD players and network audio players to this unit.
ENGLISH Connecting multiple PM-KI RUBY units (F.C.B.S. connection) n Making the F.C.B.S. connection n Connection example In the connection of the following example, an unit with ID number 1 acts as a master amplifier to control all the other slave units with ID numbers 2 to 4. Signal flow ID 1 Master CD LINE-1 LINE-2 SPEAKERS RECORDER-1 RECORDERRECORDERRECORDER-2 RECORDERRECORDER-1 RECORDERRECORDER-2 IMPEDANCE : 4 4㹼16 16Ω IN 0 The PM-KI RUBY F.C.B.S.
ENGLISH n How to set ID number for F.C.B.S. CD LINE-1 LINE-2 SPEAKERS RECORDER-1 RECORDERRECORDERRECORDER-2 RECORDERRECORDER-1 RECORDERRECORDER-2 IMPEDANCE : 4 4㹼16 16Ȑ IN OUT STEREO 1 While holding F.C.B.S. ID on the rear panel, press X. BI-AMP REMOTE CONTROL IN AUDIO IN AUDIO OUT OUT AMP MODE ID F.C.B.S. POWER AMP IN AC IN SIGNAL GND PHONO AUDIO IN 2 an ID number. Turn INPUT SELECTOR on the unit to select 0 F.C.B.S.
ENGLISH Super Audio CD player, etc. Overview L R Connections : Signal flow When in bi-amp mode, connect to the L channel input connector. CD R Set to “BI-AMP”. LINE-1 LINE-2 SPEAKERS RECORDER-1 RECORDERRECORDERRECORDER-2 RECORDERRECORDER-1 RECORDERRECORDER-2 IN OUT STEREO CD Playback L Set to “BI-AMP”. LINE-1 LINE-2 SPEAKERS RECORDER-1 RECORDERRECORDERRECORDER-2 RECORDERRECORDER-1 RECORDERRECORDER-2 IN OUT STEREO BI-AMP REMOTE CONTROL AUDIO IN AUDIO OUT OUT F.C.B.S.
ENGLISH Connection for 5.1 Multi-channel Playback Three PM-KI RUBY units can be connected by F.C.B.S. and used through linked operation. For details on F.C.B.S. connection, see “Examples of Connections” ( (v p. 10)). Connect the outputs of players that have 5.1 channel analog outputs to each of the three units. If using an active subwoofer, see the instruction manual that came with the subwoofer for further instructions.
ENGLISH n Speaker Positioning for Super Audio Multi-channel Sound Front speaker (Right) Front speaker (Left) If you use a pre-amplifier, connect it as shown below, and then you can use this unit as a power amplifier. Overview Pre-amplifier AUDIO OUT R L 60° approx.110° R L R L Connections approx.
ENGLISH Remotely connecting Marantz audio devices Connecting devices with remote control connectors Performing operations by RC on this unit without visual contact You can connect an external IR receiver to the REMOTE CONTROL connectors to perform operations on this unit with the supplied remote control unit without visual contact. This might be necessary if the unit is hidden in a cupboard or corner, so you can’t directly point with the remote control unit to the device.
ENGLISH Playback Turning the power on 16 Selecting the input source 16 Adjusting the volume 16 Turning off the sound temporarily (Muting) 16 18 Having the illumination lamp off 18 Playing CDs 18 Recording 18 0 Press X AMP on the remote control unit to turn on power from standby mode. You can also turn the INPUT SELECTOR on the main unit when the unit is in standby mode to turn on the power. n Switching the power to standby 1 Press X AMP on the remote control.
ENGLISH Adjusting the volume balance (LEVEL) and sound quality (BASS/TREBLE) n Adjusting LEVEL The volume level of the left and right channels can be trimmed in 0.5 dB steps across a 0.0 - -9.0 dB range. The factory default setting is 0.0 dB (maximum). 1 Press MODE/TRIM. The unit enters LEVEL adjustment mode. 0 If the slave (v p. 10) is connected by F.C.B.S., the device for to adjust the volume balance (LEVEL) and sound quality (BASS/TREBLE) can be switched by pressing this button.
ENGLISH Playing CDs Recording The display brightness can be adjusted between four levels. Switching the display off reduces a source of noise that affects sound quality, enabling higher sound quality playback. This section uses playback from a CD as an example. Audio signals input into this unit can be output to an external recording device. When recording audio from a playback device connected to this unit, audio can be recorded with the playback device still connected to this unit. 1 Press DISPLAY.
ENGLISH Settings Menu map By default, this unit has recommended settings defined. You can customize this unit based on your existing system and your preferences. Setting items Description Page PHONO Sets the phono equalizer of this unit according to the type of the turntable cartridge to be connected. 20 AUTO STBY (Auto Standby) Sets whether to automatically switch the unit to the standby mode when there is no audio input and no operations are performed for more than 30 minutes.
ENGLISH MM (Default): Set this for an MM cartridge. MC: Set this for an MC cartridge. Sets whether to automatically switch the unit to the standby mode when there is no input signal and operation for 30 minutes. ON (Default): Enable Auto Standby mode. OFF: Disable Auto Standby mode. The audio is muted for around 4 seconds when this setting is changed. -20 dB / -40 dB / -∞(Default: -∞) 0 0 0 The display will show the remaining time for three minutes before the units enters standby mode. In F.C.B.
ENGLISH Tips n Contents Troubleshooting Tips Power does not turn on / Power is turned off 23 Operations cannot be performed through the remote control unit 24 No sound comes out 24 25 I want to set how far the volume is decreased when the MUTE button is pressed 22 I want to turn the illumination lamps on both sides of the unit main panel off 22 Desired sound does not come out I want to use two or more of PM-KI RUBY units for high quality playback Sound is interrupted or noise occurs 25 22
ENGLISH Tips I want to set how far the volume is decreased when the MUTE button is pressed -20 dB, -40 dB or - ∞ can be set. (v p. 20) Overview 0 I want to turn the illumination lamps on both sides of the unit main panel off 0 Set the illumination lamp to off. (v p. 18) I want to use two or more of PM-KI RUBY units for high quality playback 0 Use the stereo complete bi-amp connections. (v p. 11) Use the multi-channel playback connections. (v p.
ENGLISH Troubleshooting If a problem should arise, first check the following: 1. Are the connections correct? 2. Is the set being operated as described in the owner’s manual? 3. Are the other devices operating properly? If this unit does not operate properly, check the corresponding symptoms in this section. If the symptoms do not match any of those described here, consult your dealer as it could be due to a fault in this unit.
ENGLISH n Operations cannot be performed through the remote control unit Symptom Page Batteries are worn out. Replace with new batteries. 2 Operate the remote control unit within a distance of about 7 m from this unit and at an angle of within 30°. 2 0 Remove any obstacle between this unit and the remote control unit. － 0 Insert the batteries in the proper direction, checking the q and w marks.
ENGLISH n Desired sound does not come out Symptom No sound comes out of a specific speaker. The left and right of stereo sound is reversed. Cause / Solution Page 0 Check that speaker cables are properly connected. 8 0 Adjust the left and right channel balance. 17 0 Check whether the left and right speakers are connected to the correct speaker terminals. 8 n Sound is interrupted or noise occurs Symptom When playing a record, the sound is distorted.
ENGLISH Appendix Trademark information Overview Explanation of terms Connections There are two types--MM (Moving Magnet) and MC (Moving Coil)--of cartridges for turntable. As the output levels for these two types of cartridges differ, the setting of the phono equalizer that is mounted in this unit must be switched according to the type of cartridge for your turntable. Change this setting in the “PHONO” section of the setting menu. (v p. 20) .
ENGLISH Specifications 0 RMS Power output (Simultaneous drive of both channels) : 100 W x 2 (8 Ω/ohms load, 1 kHz, T.H.D. 0.05 %) 200 W x 2 (4 Ω/ohms load, 1 kHz, T.H.D. 0.1 %) Total harmonic distortion (1 kHz, simultaneous drive of both channels, 100 W, 8 Ω/ohms load) : 0.005 % 0 Frequency response (CD, 1 W, 8 Ω/ohms load) : 5 Hz – 50 kHz ±3 dB 0 Damping factor (8 Ω/ohms load, 20 Hz – 20 kHz) : 500 0 Input sensitivity/Input impedance 0 0 PHONO (MC) : 250 μV / 100 Ω/ohms PHONO (MM) : 2.
ENGLISH 34 n Dimensions (Unit : mm) 266 Connections 400 453 68 Overview 66 Playback 19 127 109 18 Appendix 69 . 302 Tips 67 69 Settings 440 n Weight : 15.
ENGLISH Index vA Auto Standby mode ............................................................. 20 vC CD player ........................................................................ 9, 18 vD Display’s brightness ............................................................ 18 vF F.C.B.S. ............................................................................... 10 Front panel ............................................................................ 4 vI Input source ........................
3520 10603 10AM Copyright © 2018 D&M Holdings Inc. All Rights Reserved.
