Contents Connections Playback Settings Tips Appendix .
Contents Connections Playback Settings Appendix Connections 4 5 5 6 6 8 10 Accessories Inserting the batteries Operating range of the remote control unit Part names and functions Front panel Rear panel Remote control unit Tips Connecting speakers Speaker A/B connection Bi-wiring connection Subwoofer connection Connecting a playback device Connecting a recording device Connecting to a device with digital audio output connectors Connecting devices with remote control connectors Performing operations
Contents Connections Playback Settings Settings Appendix Tips Setting the Auto Standby mode Setting the remote signal receiving function Disabling the remote signal receiving function of the remote control unit Enabling the remote signal receiving function of the remote control unit Setting remote control codes Setting remote control codes for the remote control Setting remote control codes for the main unit 32 33 Tips Troubleshooting Power does not turn on / Power is turned off Operations cannot b
Contents Connections Playback Settings Tips Appendix Thank you for purchasing this Marantz product. To ensure proper operation, please read this owner’s manual carefully before using the product. After reading this manual, be sure to keep it for future reference. Accessories . Check that the following parts are supplied with the product.
Connections Contents Playback Settings Inserting the batteries 1 Tips Appendix NOTE 0 To prevent damage or leakage of battery fluid: 0 Do not use a new battery together with an old one. 0 Do not use two different types of batteries. 0 Remove the batteries from the remote control unit if it will not be in use for long periods. 0 If the battery fluid should leak, carefully wipe the fluid off the inside of the battery compartment and insert new batteries.
Contents Connections Playback Settings Tips Appendix Part names and functions Front panel q w e r . y u i t o Q0 Q1 Q2 For details, see the next page.
Contents q w Connections e Playback r Settings Tips Appendix F Headphones jack (PHONES) Used to connect headphones. Turn off speaker output when using headphones. (v p. 27) t NOTE 0 To prevent hearing loss, do not raise the volume level excessively when using headphones. G BASS control knob This setting adjusts the volume level for the bass. (v p. 28) . y u i o Q0 Q1Q2 H SOURCE DIRECT button/indicator This turns source direct mode on/off. (v p.
Contents Connections Playback Settings Tips Appendix Rear panel q w . u e i r o For details, see the next page.
Contents q Connections w e Playback r t Settings Tips Appendix E Remote control input/output connectors (REMOTE CONTROL) Used to connect to a Marantz audio device that is compatible with the remote control function. (v p. 23) y . F AC inlet (AC IN) Used to connect the power cord. (v p. 24) u G Analog audio input connectors (AUDIO IN) Used to connect devices equipped with analog audio output connectors. 0 “Connecting a playback device” (v p. 20) 0 “Connecting a recording device” (v p.
Contents Connections Playback Settings Tips Appendix Remote control unit The remote control provided with this unit can control a network audio player in addition to a Marantz CD player. 0 “CD player operations” (v p. 11) 0 “Network audio player operations” (v p. 13) q t o Operating this unit w A Remote control signal transmitter This transmits signals from the remote control unit. (v p. 5) B Input source select buttons This selects the input source. (v p.
Contents Connections Playback Settings Tips Appendix o CD player operations You can operate a Marantz CD player. To operate a Marantz CD player, press the REMOTE MODE CD button to switch the remote control to the CD player operation mode. 0 REMOTE MODE CD button lights for approximately two seconds.
Contents Connections Playback Settings Tips Appendix M OPTION button N SETUP button O CLEAR button P DIMMER button Q REPEAT button (L) 0 The remote control may not operate some products. 0 The amp can be operated with the amp operation buttons even when the remote control operation mode is set to CD.
Contents Connections Playback Settings Tips Appendix o Network audio player operations You can operate a Marantz network audio player. To operate a Marantz network audio player, press the REMOTE MODE NET button to switch the remote control to the network audio player operation mode. 0 REMOTE MODE NET button lights for approximately two seconds.
Contents Connections Playback Settings Tips Appendix K FAVORITES ADD / CALL buttons L OPTION button M SETUP button N Number/letter buttons (0 – 9, +10) O CLEAR button P DIMMER button Q REPEAT button (L) Q1 0 The remote control may not operate some products. 0 The amp can be operated with the amp operation buttons even when the remote control mode is NET.
Contents Connections Playback Settings o Contents Tips Appendix o Cables used for connections 16 Connecting a playback device 20 Connecting a recording device 21 Connecting to a device with digital audio output connectors 22 Connecting devices with remote control connectors 23 Connecting the power cord 24 Provide necessary cables according to the devices you want to connect. Speaker cable . Connecting speakers . Subwoofer cable NOTE Coaxial digital cable .
Contents Connections Playback Settings Tips Appendix Connecting speakers o Connecting the speaker cables NOTE 0 Disconnect this unit’s power plug from the power outlet before connecting the speakers. 0 Connect so that the speaker cable core wires do not protrude from the speaker terminal. The protection circuit may be activated if the core wires touch the rear panel or if the + and - sides touch each other. (“Protection circuit” (v p.
Contents Connections Playback Settings Tips Appendix Speaker A/B connection This unit is equipped with two sets of speaker terminals (SPEAKER A and SPEAKER B). One set of speakers can be connected to each set of terminals, and a total of two sets of speakers can be connected. The same signal is output from the SPEAKERS A and SPEAKERS B terminals. When only one set of speakers is to be connected, use either the SPEAKERS A or SPEAKERS B terminals. w q (R) w q w (R) (L) .
Contents Connections Playback Settings Tips Appendix Bi-wiring connection This connection limits the effects of signal interference between the high range speakers (tweeters) and low range speakers (woofers), allowing you to enjoy high quality playback. When bi-wiring with bi-wireable speakers, connect the mid and high range terminals to SPEAKERS B (or SPEAKERS A), the low range terminals to SPEAKERS A (or SPEAKERS B).
Contents Connections Playback Settings Subwoofer connection Use a subwoofer cable to connect the subwoofer. . Subwoofer 0 The subwoofer volume is linked to the Speaker A volume. 0 This unit does not output to the subwoofer when not set to output audio from the SPEAKERS A terminal. (v p.
Contents Connections Playback Settings Tips Appendix Connecting a playback device You can connect turntables, CD players, network audio players and tuners to this unit. This unit is compatible with turntables equipped with a moving magnet (MM) phono cartridge. When you connect to a turntable with a low output moving coil (MC) cartridge, use a commercially available MC head amp or a step-up transformer.
Contents Connections Playback Settings Tips Connecting a recording device Recording device AUDIO OUT R L AUDIO IN R L L R L R L R L . R NOTE 0 Never insert the short-circuiting pin plug into the recording output connectors (AUDIO OUT RECORDER). Doing so could result in damage.
Contents Connections Playback Settings Tips Appendix Connecting to a device with digital audio output connectors Use this connection to input digital audio signals to this unit, and convert the signals for playback using the D/A converter of this unit. (v p. 29) TV / Satellite receiver etc. OPTICAL OUT COAXIAL OUT . or NOTE 0 Linear PCM signals with a sampling frequency of 32 kHz, 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, or 192 kHz can be input into this unit.
Contents Connections Playback Settings Tips Appendix Connecting devices with remote control connectors Remotely connecting Marantz audio devices Performing operations by RC on this unit without visual contact You can transmit remote control signals simply by connecting a Marantz audio device to the REMOTE CONTROL IN/OUT connectors using the remote connection cable provided with the device.
Contents Connections Playback Settings Connecting the power cord After completing all the connections, insert the power plug into the power outlet. To household power outlet (AC 120 V, 60 Hz) .
Contents Connections Playback Settings o Contents Turning the power on 26 Switching the power to standby 26 Selecting the speakers for audio output 27 Selecting the input source 27 Adjusting the volume 27 Turning off the sound temporarily (Muting) 27 Adjusting the tone and balance 28 Playing CDs 28 Connect and playback from a digital device (Coaxial/Optical) 29 Recording 30 Front panel Rear panel Remote control unit 25 Index Tips Appendix
Contents Connections Playback Settings Appendix Turning the power on AMP POWER X 1 Input source select buttons SOURCE DIRECT Tips Press X on the main unit to turn the power on. Input indicator for the selected source lights in blue. 0 Press AMP POWER X on the remote control unit to turn on power from standby mode. 0 You can also turn the INPUT SELECTOR on the main unit when the unit is in standby mode to turn on the power. VOLUME df MUTE .
Contents Connections Playback Settings Selecting the speakers for audio output 1 1 Use SPEAKERS A/B on the main unit to select the speaker system to be used for playback. Use VOLUME df to adjust the volume. 0 You can also adjust the master volume by turning VOLUME on the main unit. 0 When using headphones, press SPEAKERS A/B to turn off all of the indicators and turn audio output from the speaker terminals off.
Contents Connections Playback Settings Adjusting the tone and balance 1 2 Tips Appendix Playing CDs This section uses playback from a CD as an example. Press SOURCE DIRECT to turn off source direct mode. 1 2 The SOURCE DIRECT indicator turns off. Turn the BASS, TREBLE and BALANCE on the main unit to adjust the tone. Press X on the main unit to turn the power on. Press the input source select button (CD) to switch the input source to “CD”. The “CD” input indicator lights in blue.
Contents Connections Playback Settings This unit is equipped with a sound quality adjusting function which allows users to enjoy the desired playback sound quality. This function only works when a digital audio signal is input. Connect digital device to this unit. (v p. 22) 1 Press the input source select button (COAXIAL or OPTICAL) to switch the input source to COAXIAL, OPTICAL 1 or OPTICAL 2. Press FILTER 1・2. This unit switches between Filter 1 and Filter 2 each time the button is pressed.
Contents Connections Playback Settings o Specifications of supported audio formats Audio signals input into this unit can be output to an external recording device. When recording audio from a playback device connected to this unit, audio can be recorded with the playback device still connected to this unit. 0 The FILTER 1･2 indicator lights only when the input source is “COAXIAL”, “OPTICAL 1” or “OPTICAL 2”. 0 If the sampling frequency switches, the sound may be cut for 1–2 seconds.
Contents Connections Playback Settings o Contents Setting the Auto Standby mode 32 Setting the remote signal receiving function 33 Setting remote control codes 34 Front panel Rear panel Remote control unit 31 Index Tips Appendix
Contents Connections Playback Settings Tips Appendix Setting the Auto Standby mode You can set the unit to automatically switch to standby mode if the unit is not operated for 30 minutes when there is no audio input (Auto Standby mode). Auto Standby mode is set to off by default. 1 Press and hold SOURCE DIRECT for 5 seconds or more to switch it on and off. The power indicator changes as follows each time it is switched on and off.
Contents Connections Playback Settings Tips Appendix Setting the remote signal receiving function When you connect a IR receiver (sold separately) to the REMOTE CONTROL IN connector of this unit, use the following procedure to disable the remote signal receiving function of this unit. When the function is enabled, you can not perform operations with the remote control unit. By default, this function is enabled.
Contents Connections Playback Settings Tips Appendix Setting remote control codes Remote control codes are set between this unit and the supplied remote control. You can select one of the three types of remote control codes, and the remote control can be used to control the unit when the same remote control code is used. If three of these units are used in the same location, all three units can be controlled simultaneously using one remote control in the default settings.
Contents Connections Playback Settings Setting remote control codes for the remote control 1 0 Set the remote control code to AMP1, AMP2 or AMP3 according to the selected number button. NOTE 0 The remote control codes returns to the default settings when the batteries are removed. Set the remote control codes again after replacing the batteries. Rear panel Remote control unit Point the remote control for which the remote control code was set at the main unit, and press REMOTE MODE CD and ENTER.
Contents Connections Playback Settings Tips Appendix o Contents Tips Troubleshooting I want to play TV audio at higher quality 37 Power does not turn on / Power is turned off 39 I want to adjust the tone myself 37 Operations cannot be performed through the remote control unit 40 I want sound playback that is faithful to the original sound 37 No sound comes out 41 I want to switch the filter to change the desired sound quality 37 Desired sound does not come out 41 I want to use bi-wi
Contents Connections Playback Settings Tips Appendix Tips I want to play TV audio at higher quality 0 Connect the digital audio output connector of the TV to the digital audio input connector (COAXIAL, OPTICAL 1 or OPTICAL 2) of this unit, and switch the input source to the connected (COAXIAL, OPTICAL 1 or OPTICAL 2) connector. (v p. 22) 0 Only 2-channel linear PCM can be input as the digital audio signal to this unit.
Contents Connections Playback Settings Tips Appendix Troubleshooting If a problem should arise, first check the following: 1. Are the connections correct? 2. Is the set being operated as described in the owner’s manual? 3. Are the other devices operating properly? If this unit does not operate properly, check the corresponding symptoms in this section. If the symptoms do not match any of those described here, consult your dealer as it could be due to a fault in this unit.
Contents Connections Playback Settings Tips Appendix Power does not turn on / Power is turned off Power is not turned on. 0 Check whether the power plug is correctly inserted into the power outlet. (v p. 24) Power automatically turns off. 0 The Auto Standby mode is on. When approx. 30 minutes pass with no audio input and no operations on the unit, this unit automatically enters the standby mode. To turn off the Auto Standby mode, press the SOURCE DIRECT button for 5 seconds or longer. (v p.
Contents Connections Playback Settings Tips Appendix Operations cannot be performed through the remote control unit Operations cannot be performed through the remote control unit. 0 Batteries are worn out. Replace with new batteries. (v p. 5) 0 Operate the remote control unit within a distance of about 23 ft/7 m from this unit and at an angle of within 30°. (v p. 5) 0 Remove any obstacle between this unit and the remote control unit.
Connections Contents Playback Settings Tips Appendix No sound comes out No sound comes out of speakers. 0 Check the connections for all devices. (v p. 15) 0 Insert connection cables all the way in. 0 Check that input connectors and output connectors are not reversely connected. 0 Check cables for damage. 0 Check that speaker cables are properly connected. Check that cable core wires come in contact with the metal part on speaker terminals. (v p. 16) 0 Securely tighten the speaker terminals.
Contents Connections Playback Settings Tips Appendix Sound is interrupted or noise occurs When playing a record, the sound is distorted. 0 Adjust to a proper needle pressure. 0 Check the tip of the needle. 0 Replace the cartridge. When playing a record, a humming noise comes out of the speakers. 0 Check that the turntable is connected correctly. (v p. 20) 0 If there is a TV or AV device near the turntable, such devices may affect the playback sound.
Contents Connections Playback Settings Tips D/A converter Explanation of terms o Specifications of supported audio formats Sampling frequency Sampling involves taking a reading of a sound wave (analog signal) at regular intervals and expressing the height of the wave at each reading in digitized format (producing a digital signal). The number of readings taken in one second is called the “sampling frequency”. The larger the value, the closer the reproduced sound is to the original.
Contents Connections Playback Settings . Trademark information Adobe, the Adobe logo and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.
Contents Connections Playback Settings Tips Specifications 0 RMS Power output (20 Hz – 20 kHz simultaneous drive of both channels) : 45 W x 2 (8 Ω/ohms load) 60 W x 2 (4 Ω/ohms load) 0 Total harmonic distortion (20 Hz – 20 kHz simultaneous drive of both channels, 8 Ω/ohms load) : 0 Output band width (8 Ω/ohms load, 0.06 %) : 0.
Contents Connections Playback Settings 0 Tone Control BASS (50 Hz) : ±10 dB TREBLE (15 kHz) : ±10 dB 0 Digital input Coaxial : 0.5 Vp-p Optical : –27 dBm or later 0 Operating temperature: +5 ℃ - +35 ℃ 0 Power supply : AC 120 V, 60 Hz 0 Power consumption : 155 W 0 Power consumption in standby mode : 0.3 W For the purpose of improvement, the specifications and design are subject to change without notice.
Contents Connections Playback Settings Tips 3/4 (16) 8 7/8 (225) 2 3/8 (60) 14 5/8 (370) 13 (330) 1 7/8 (45) 1 (24) o Dimensions (Unit : in. (mm)) 2 1/4 (56) 4 1/4 (105) 2 (50) 13 1/2 (340) . 2 (50) 5/8 (14) 3 5/8 (91) 17 3/8 (440) o Weight : 17 lb 3 oz (7.
Contents Connections Index Playback Settings vM Auto Standby mode ........................................ 32 vB BALANCE ...................................................... 28 BASS ............................................................. 28 CD player ................................................. 20, 28 Network audio player ..................................... 20 vP Input source ................................................... 27 Speakers ............................................
. 3520 10763 00AM © 2020 Sound United. All Rights Reserved.
PM6007 Integrated Amplifier QUICK START GUIDE
Welcome Thank you for choosing a Marantz amplifier. This guide provides step-by-step instructions for setting up your amplifier. Before You Begin What’s In the Box Quick Start Guide Amplifier Owner’s Manual Power cord Safety Instructions Remote control unit (RC004PMCD) Warranty (for USA/ for CANADA) R03/AAA batteries Required for Setup CD Player Speaker systems Speaker cables These drawings are for illustrative purposes only and may not represent the actual product(s).
Setup There are six steps to the setup process.
Connect the speakers to PM6007 (R) (L) Connecting the speaker cables q w w q q Peel off about 3/8 inch (10 mm) of sheathing from the tip of the speaker cable, then either twist the core wire tightly or apply solder to it. w Turn the speaker terminal counterclockwise to loosen it. e Insert the speaker cable’s core wire to all the way into the speaker terminal. r Turn the speaker terminal clockwise to tighten it.
EN Connect the CD player to PM6007 CD player FR Plug the power cord into a power outlet ES AUDIO OUT R L R L L R PM6007 Connect to household power outlet Power cord (supplied) (AC 120 V, 60 Hz) 4
Turn on the power of PM6007 and then set the speakers for audio output to SPEAKERS A Begin CD playback 1 Set the input source to “CD”. 1 Reduce the volume to the minimum level. 2 Play the CD player. 2 Press the power operation button. 3 Adjust the volume. 3 Press SPEAKERS A. The SPEAKERS A indicator lights and the speakers for audio output are set to SPEAKERS A.
Owner’s Manual EN FR • Refer to the Online Manual for other functions information and operation procedure details. manuals.marantz.com/PM6007/NA/EN/ ES Online Manual • For more information, visit www.marantz.
Printed in Vietnam 5411 11863 00AM © 2020 Sound United. All Rights Reserved.
The Most Musical Sound PM6007 Integrated Amplifier The PM6007 delivers Marantz’ most musical sound and is an ideal choice for those ready to take the next step in their 2-channel Hi-Fi system. Powered by a Toroidal power transformer and customized block capacitors, the PM6007 integrated amplifier delivers 45 watts (8ohm, 20Hz-20kHz). You can easily connect both analog and digital sources or connect your turntable to the built-in phono MM pre-amp with FET input.
PM6007 Technical Specs Features Channels 2 Full balanced circuitry architecture Double Mono Power Amp construction - Digital in: USB-B / optical / coaxial / USB-A -/2/1/- Current Feedback Topology Phono EQ: Standard / Marantz Musical / Marantz Musical Premium Sample Rate digital In USB-A: DSD / WAV / FLAC / AIFF / ALAC USB-B DSD Audio Streaming (DoP): DSD2.8 / DSD5.
For U.S.A. ■na•antz® Limited Warranty Marantz America, Inc. ("Marantz") warrants the following Marantz Products for the periods indicated: 1. The following Marantz Audio/Video components, have a 3 year warranty for both Parts & Labor, from the original purchase date: Amplifiers, Pre Amplifiers, Pre Amplifier-ProcessorTuners, Integrated Amplifiers, Tuners, Receivers, Blu-ray DVD SA-CD/CD Players/Changers, Learning Remote Control Devices, iPod Docks & DLP front Projectors.
For CANADA ■naaeantz® MARANTZ CANADA LIMITED WARRANTY Marantz Canada ("Marantz") warrants the following Marantz products for the periods indicated: Who May Enforce the Warranty 3-year warranty for both Parts & Labour, from the original purchase date : What We Will Pay For Amplifiers; Pre Amplifiers; Pre Amplifier-Processor-Tuners; Integrated Amplifiers; AV Pre Tuner; Tuners; Receivers; AV Surround Receiver; Blu-ray DVD Super Audio CD/CD Players/ Changers; CD Receiver; Turntable; Network Audio Player; D
Safety Instructions marantz . (Read these safety instructions before operating the unit.) 0 SAFETY PRECAUTIONS CAUTIONS ON INSTALLATION CAUTION: To completely disconnect this product from the mains, disconnect the plug from the wall socket outlet. The mains plug is used to completely interrupt the power supply to the unit and must be within easy access by the user. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
CAUTION (FOR AMPLIFIER): HOT SURFACE. DO NOT TOUCH. The top surface over the internal heat sink may become hot when operating this product continuously. Do not touch hot areas, especially around the "Hot surface mark" and the top panel. Hot surface mark PRECAUTION (POUR AMPLIFICATEUR) : SURFACE CHAUDE. NE PAS TOUCHER. La surface superieure du dissipateur de chaleur peut devenir chaude si vous utilisez ce produit en continu.
CAUTIONS ON USING BATTERIES AVISOS SOBRE DE LAS PILAS There is a possibility of smoke, fire, explosion from the battery, Please note as following. • Insert the specified batteries in the remote control un it. • Replace the batteries with new ones if the set does not operate even when the remote control unit is operated close to the unit. (The supplied batteries are only for verifying operation. Replace them with new batteries at an early date.
