® Model LN9101M Installation Guide Anamorphic Lens System
The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. WARNING - TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. IMPORTANT SAFETY INSTRUCTIONS! PLEASE READ THEM BEFORE OPERATING THIS EQUIPMENT. 1. Read these instructions. 2. Keep these instructions. 3.
ADDITIONAL SAFETY INSTRUCTIONS! WARNING: THERE IS A POSSIBILITY OF SERIOUS INJURY IF YOU DO NOT FOLLOW THESE INSTRUCTIONS. When mounting the projector to a building structure, it is important to follow all of the local building/construction codes. The total weight of the Marantz VP-11, LN9101M Anamorphic Lens System and MT20/EXT10 Mounting Brackets is 80 lbs (36.29 kg). Make sure the ceiling structural members can support five times the total weight, which is 400 lbs (181.44 kg).
Table of Contents Safety Instructions ....................................................2 Thank You and Please Take a Moment ....................2 Technical Assistance and Customer Service ...........2 Table of Contents......................................................3 Important, Connector and Cable Information ...........4 Dimensions ...............................................................5 Installation Overview ................................................5 Installation .................
Dimensions The following dimensions can assist in determining the best location 21-15/16" for the 55.7cm combination of the Marantz 9-13/16" VP-11 24.9cm 22-1/2" and the 57.2cm LN9101M Anamorphic Lens System. Installation Overview The LN9101M Anamorphic Lens System is designed to mount together with the Marantz VP-11 onto the ceiling of a typical room. Before choosing the location on the ceiling, it is important to first read the “Installation” section of the VP-11 User Guide.
EXT10 Assembly, con’t Set the Pole Pieces to the desired length and secure the position using the two Round Head Philips 1/4-20 x 2-1/4 Screws and two 1/420 Lock Nuts. Refer to figure 3. 5. Tighten all the recently install hardware and proceed to assemble the LN9101M. LN9101M Sled Mounting screw locations 24” to 43-3/4” 14-5/8” to 24” Plate 4 and LN9101M Sled Sled Mounting Plate Figure 3 Figure 6 LN9101M Assembly Assemble the LN9101M by performing the steps below: 1.
MT20 Assembly Assemble the MT20 by performing the steps below, refer to figure 10: MT20 and LN9101M Mounting Plates MB20 and LK1 Mounting Plates Plate 1 Plate 2 Plate 3 (LN9101M) Plate 4 (LK1) Figure 10 Notes: The MT20 hardware, fasteners, mounting template and parts list are located in a separate shipping carton from the projector. Plate #4 supplied with the LN9101M will be used instead of the MT20 Plate #4. 1.
MT20 Assembly, con’t Note: When the EXT10 Extension Pole will be used, attach the “Inner Pole” end to Plate #3 (instead of Plate #2) using four (4) 5/16-18 inch nuts and washers provided. EXT10 Refer to figure 17. 6. Invert the projector and Plate #3 place it on a soft, flat surface. Align the three 6mm mounting holes on the projector with the Figure 17 mounting holes on Plate #4 and the LN9101M Sled. Secure the bracket to the projector using the three 6mm screws. Refer to figures 18 and 19.
turns. Place the removed cover in a safe place for possible future use. 3. The inner circumference of the Lens Holder is threaded to accept the Lens. It is exSmall Lens Cover tremely important not to cross thread the Lens or Lens Holder when startFigure 22 ing the fastening process and do not over tighten. Refer to figure 23. 4. Orient the Lens Holder/Lens over the end of Lens Holder Mounting Post as illustrated in figures 24 and 25.
LN9101M Lens Alignment, con’t 3. Press the LENS IN Push-button on the Remote Control and the Lens will travel to a position in front of the projector Lens. Verify the horizontal center of the LN9101M Lens coincides with the horizontal center of the projector Lens. If the LN9101M Lens doesn’t line up, loosen the screws on the LN9101M Sled and slide the Top Adjustment Plate slightly to the left or right relative to Plate 4 to center the Lens. Tighten the screws. Refer to figures 4A, 4B, 4C and 5 on page 6.
For U. S. A. ® Limited Warranty Marantz America, Inc. (“Marantz”) warrants the following Marantz Products for the periods indicated: 1. The following Marantz Audio/Video components, have a 3 year warranty for both Parts & Labor, from the original purchase date: Amplifiers, Pre Amplifiers, Pre Amplifier-Processor- Tuners, Integrated Amplifiers, Tuners, Receivers, DVD Players, CD-Recorders, CD Players, Audio Cassette Decks, Learning Remote Control Devices, Universal Dock & DLP Front Projectors. 2.
www. marantz.com You can find your nearest authorized distributor or dealer on our website. U. S. A. Marantz America, Inc. 100 Corporate Drive, Mahwah, NJ 07430, U. S. A. ® Printed in U. S. A. Part No. 04104000 is a registered trademark.
