Wide Conversion Lens System LN-11S1A
IMPORTANT SAFETY INSTRUCTIONS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1. Read these instructions.
ENGLISH ESPAÑOL WARRANTY For warranty information, contact your local Marantz distributor. GARANTIA Para obtener información acerca de la garantia póngase en contacto con su distribuidor Marantz. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz.
CE MARKING English The LN-11S1A is in conformity with the EMC directive and low-voltage directive. Français Le LN-11S1A est conforme à la directive EMC et à la directive sur les basses tensions. Español El LN-11S1A está de acuerdo con las normas EMC y las relacionadas con baja tensión. Deutsch Das Modell LN-11S1A entspricht den EMC-Richtlinien und den Richtlinien für Niederspannungsgeräte. Italiano Il LN-11S1A è conforme alle direttive CEE ed a quelle per i bassi voltaggi.
NAMES OF PARTS......................................................................................................................................2 BASIC OPERATION....................................................................................................................................3 TURNING THE POWER ON............................................................................................................................................................3 TURNING THE POWER OFF..............
NAMES AND BEFORE USE FUNCTIONS BEFORE USE NAMES OF PARTS CHECKING THE UNIT AND SUPPLIED ACCESSORIES Before use, check that the main unit and supplied accessories given below are assembled. • Anamorphic lens x 1 Focus adjustment screw (Page. 11) Lens center mark • AC power cord (for U.S.A.) x 1 NAME OF PARTS Height/tilt adjustment screw (Page. 10) POWER ON indicator (Page. 3) Trigger signal input indicator (Page.
Standard 1 Picture Adjust Auto Power Off Disable Fine Menu 1 Trigger 2 Full Off Fine Menu 2 Trigger 2 Normal Off Input Signal Trigger 2 Zoom Off RGB/HD Adjust Trigger 2 V-stretch On HDMI Trigger 2 Through Off Display Remote Control OSD/Blanking Reset Lamp Life Config. Reset All NAME OF PARTS USING VP-11 OR VP-15 SERIES TRIG. 2 OUTPUT JACK Display the projector’s setup menu and set Trigger 2 V-stretch to On and turn all other settings Off.
BEFORE USE BASIC OPERATION CONCERNING CONNECTORS AND CABLES NAME OF PARTS REMOTE CONTROL CODE The operating range for a remote controller and this unit is shown in the figure below. Not only is it possible to control this unit using the remote controller (AUX1 and AUX2) of a VP-11 series or VP-15 series projector, but it is also possible to control this unit using a programmable remote controller (such as an RC9001 or RC2001). Commands used to control this unit are given in the table on the right.
This unit can be controlled using a programmable remote controller (such as an RC9001 or RC2001). For commands used to control this unit, refer to the table at right. For details on programmable remote controllers, contact your Marantz dealer or Marantz Consumer Marketing. RC5 Command 56 00 62 00 56 00 62 Moves the anamorphic lens to the operating position. Moves the anamorphic lens to the 01 operating position. Moves the anamorphic lens to the 20 non-operating position.
BEFORE USE SETUP SETUP PROCEDURE 3. EXT10 ASSEMBLY Install the LN-11S1A according to the procedure outlined in the flowchart below. NAME OF PARTS Start Mounting on the floor? Y Note: N BASIC OPERATION EXT10 needed? After reading the “Installation” Section of the VP-11/VP-15 User Guide and it has been determined the EXT10 Extension Pole will be needed to meet the requirements of location and ventilation for the Projector, assemble the EXT10 by performing the steps below.
1. Assemble the MOUNT20 by performing the steps below, refer to Figure 8: MOUNT20 and LN-11S1A Mounting plates 1. Insert Base Plate connectors q into the lateral positioning slots e from the underside of Plate 1. The lateral positioning slots will give you 2-1/4 inches of lateral adjustment for projector alignment. Refer to Figure 9. Plate #1 Secure the lens slider to the base plate using the supplied machine screws (M3 x 8) in 6 locations.
BEFORE USE SETUP 3. NAME OF PARTS Install the combined Plates #1 and #2 (or Plate 1 with the EXT10) securely to the Building Structure following all of the Local Building/Construction Codes. Use suitable hardware in adequate quantity and size depending on the installation requirements. 4. Attach the Horizontal Tilting Plate #3 to the previously combined plates (already installed on ceiling) using the 1/4-20 inch screws provided. Refer to Figures ?? and ??.
Mount the assembled LN-11S1A and MOUNT20 to the projector. Refer to Figure 16. Mountina slits Note: Plate #4 supplied with the MOUNT20 is located in a separate shipping carton from the projector or LN-11S1A. BASIC OPERATION ADVANCED OPERATION Figure 18 Projector side Notes: 20˚ tilt REMOTE CONTROLLER SETUP OPERATION • When the projector is combined with the ceiling mounting kit, the total weight is approximately 59 pounds (26.7kg). For safety, assembly should be performed by two or more people.
BEFORE USE SETUP MOUNTING THE LN-11S1A (ON THE FLOOR) MOUNTING THE LN-11S1A LENS NAME OF PARTS Mount the lens to the projector, whose operations have already been confirmed, according to the procedure given below. Mount the assembled LN-11S1A to the projector. Refer to Figure 20. 1. BASIC OPERATION Figure 20 1.
Aim the remote controller included with the VP11 or VP15 series projector at the remote control receiver of the lens slider and press the AUX1 button to move the anamorphic lens to the operating position. Check that the center of the LN-11S1A anamorphic lens in the horizontal direction is aligned with the center of the projector’s lens in the horizontal direction. If the centers are not aligned, adjust by turning the screws shown in the figure to the right in the direction of the arrow. Refer to Figure 27.
OTHERS Before requesting repairs, check the following items. 1. NAME OF PARTS 2. PROJECTION DISTANCE CHART FOR VP-11 AND VP-15 PROJECTORS Are the connections among each of the devices the same as given under “BASIC OPERATION” (Page. 3). Are operations being performed correctly according to information given in “BASIC OPERATION” (Page. 3) BASIC OPERATION If the unit is not functioning properly, check the items given in the table below.
3.5 mm diameter monaural mini-jack Input resistance, approx 20k Ohms ....... 1 system Trigger output 3.5 mm diameter monaural mini-jack Direct connection to trigger input .......... 1 system (Max. 350 mA) 5 V DC input (special AC/DC adapter) Maximum External Dimensions Width: 14-5/16 inches (363 mm) Depth: 12-13/16 inches (325.5 mm) Height: 6-1/4 inches (159 mm) Weight 6 pounds (2.
www.marantz.com You can find your nearest authorized distributor or dealer on our website. is a registered trademark.
