Owner`s manual

25
11. WIRELESS KEYLESS ENTRY SYSTEM (cont’d)
REPLACING THE BATTERIES (Fig. 46)

Turn counterclockwise the key on the bottom of the spacer
and remove the Keyless Entry System from the spacer.

Release the backplate of the Keyless Entry System.

Remove old batteries.

Replace with 2 new 3V batteries, CR 2032. Match polarity
designation. Test operability. (Keyless Entry System is
designed to remember all previously programmed codes and
PINs while battery is being replaced).

Replace the backplate.
For protection of keypad, keep cover closed when not in use.
Fig. 46
Backplate
2 Batteries 3V, CR 2032
12. OPERATION OF YOUR OPERATOR
Fig. 47
Lock/Vacation Button
Light On/Off Button
Illuminated Door Pushbutton
B. Wall Control Panel
Your operator can be activated via any of the following, depending
on which accessories your operator system has:

Remote Control Transmitter

Wall Control Panel

Keyless Entry (optional accessory)
REMOTE CONTROL TRANSMITTER:

To open or close garage door, press and hold button
(Transmitter has an indicator light that will illuminate).
See Fig. 47A. When garage door begins to move, release button.

To stop garage door during travel, press and hold button until
door stops, then release button.

To resume garage door travel after stopping, press button again.
Door begins to move in the opposite direction.
WALL CONTROL PANEL:

The Door Pushbutton will light when Wall Control properly
connected (if it does not light up, review section 8-11. “Install
Wall Control” on page 15 or refer to “Having a Problem” on
page 33).
To open or close garage door, press and hold Illuminated Door
Pushbutton. See Fig. 48. When garage door begins to move,
release button.
To stop garage door during travel, press and hold button until
door stops, then release button.
To resume garage door travel after stopping it, press button
again. Door begins to move in the opposite direction.

The Light On / Off button can be used to turn lights on or off.
When using the light On / Off button, the automatic timer is
ignored, and the lights will remain on until the button is pressed
again, or until the operator is activated and the automatic
timer begins again.

The Lock/Vacation button can be used to lock out all remote
control transmitters. The door can still be activated by wall
control panel or keyless entry system.
Press and hold Lock/Vacation button for 2-3 seconds. Release
button. Illuminated Door Pushbutton will flash continuously
while lock mode is active. To unlock operator, press and hold
Lock/Vacation button for 2-3 seconds.
Indicator Light
Buttons
A. Transmitter
8
8-4. INSTALL HEADER BRACKET
If the header bracket is not rigidly fastened to a sound
structural support on the header wall or ceiling, the
safety reverse system may not work and could cause
serious injury or death. DO NOT move or adjust springs
or garage door hardware, as these parts are under
extreme tension and could cause injury or death.
Fig. 10
Pin Hole
Fig. 11
Insert 1/4-20 x 2-1/2”
Carriage Bolts
from outside of door
Lock Washer
1/4-20 Nut
Wood Sectional
Doors
Door Bracket
Header
Lag Screw for Header installation
if necessary (not provided)
Header Bracket
5/16 x 1-3/4"
Lag Screw
Pilot Holes
Fig. 12
Fig. 13
Pilot Hole
Ceiling
Header Bracket
Lag Screw
8-3. INSTALL DOOR BRACKET TO DOOR
Wood Sectional Doors (Fig. 11)

Position door bracket (Fig. 10) along vertical center line of
door with pin hole facing top of the door and top edge of
the bracket 4” to 5” below top edge of the door, or roughly
at the same height as top rollers on the door.

Mark locations of securement holes through door bracket.

Drill two 1/4" holes through door for securement of door
bracket.

Insert carriage bolts (1/4” x 2-1/2”) from the outside through
door and bracket, then secure with lock washers and nuts
from the inside.

Tighten nuts firmly.

Remove and save clevis pin from header bracket assembly.

Mark pilot holes location on header through header bracket
holes where lag screws will be inserted.
See Fig.12 for which header bracket holes to use.

Drill 3/16" pilot holes into header.

Install bracket with lag screws (5/16 x 1-3/4”) provided.

Tighten lag screws firmly.
NOTE: Follow the same procedure if header (shown in
Fig. 8) runs vertically instead of horizontally and is the only
option for mounting header bracket to header wall. In case
of minimal clearance above the garage door, the header
bracket may be mounted to the ceiling. Follow the same
steps above to ensure a sound surface for mounting.
Important Note: If the vacation lock
mode is engaged.
By pressing and holding the light button
or the door activation button for one
second or longer will disengaged the
vacation lock mode.
NOTE: The Light On / Off button must be pressed twice,
in order to turn the operator light(s) off after a
door cycle (activation).