Operating instructions

ManualsBrandsMarantec ManualsGarage Door OpenerElite 2007

Part#: 70229 Printed in the U.S.A. Version 01/07

21. MAINTENANCE AND ADJUSTMENTS RECORD

To ensure continued safe operation and extended life of your opener system, periodic checking for proper operation is necessary. Occasional

maintenance and readjustment of your system may also be needed.

MONTHY:

 Check reversal system by performing

“SAFETY REVERSAL TEST” described in

this manual.

 Check proper operation of door by

manually moving door open and closed.

If door binds or sticks, or is out of balance

call for garage door service.

 Check and test photo eye safety system

as described in this manual.

ONCE EVERY

YEAR

 Keep door rollers, hinges,

and bearings properly

lubricated by following

recommended door

instructions or contacting

a door service company

in your area.

AS NEEDED:

 Readjust opener travel limits and force settings as necessary

— due to cold weather, normal wear of door, etc.

The convenient adjustment instruction label on the opener

can be used for any periodic adjustments needed.

 Check and readjust belt tension, if necessary, in the unlikely

event that it loses its proper tension during the life of the

opener.

 Always check the reversal system after any adjustment of

travel limits or forces. A door opener that is not checked

could possibly be out of adjustment and be dangerous.

Good maintenance of your garage door is an imperative requirement. Not only will it prolong the life of the door and the opener,

but more importantly, it assures your safety and that of others. Use the form below to record the monthly, yearly, and “as needed”

maintenance.

Maintenance Date Performed By Comments

If you run out of Maintenance Record lines, please make yourself another record sheet.

EN 55011

EN 50081

EN 50082

ETS 300220

No part of this manual may be reproduced without our prior written approval.

We reserve the right to alter details in the interests of progress.

Garage Door Opener System

Installation and Operating Instructions

Deluxe EX-2005

Elite EX-2007

Digital Intelligence for the Garage

Marantec America Corporation

5705 Centerpoint Court, Gurnee, IL 60031 U.S.A.

Phone 1-888-622-2489



Fax 847-478-0348

Summary of content (18 pages)

PAGE 1
Garage Door Opener System 21. MAINTENANCE AND ADJUSTMENTS RECORD To ensure continued safe operation and extended life of your opener system, periodic checking for proper operation is necessary. Occasional maintenance and readjustment of your system may also be needed. MONTHY:  Check reversal system by performing “SAFETY REVERSAL TEST” described in this manual.  Check proper operation of door by manually moving door open and closed.
PAGE 2
19. ERROR MESSAGES OWNER’S MANUAL CONTENTS 1. INTRODUCTION 2 2. ADVANCED FEATURES 2 3. IMPORTANT SAFETY INFORMATION 3 4. TOOLS 4 5. GARAGE 4 6. OPENER PACKAGE CONTENTS 6 7. INSTALLATION STEPS 8. OPENER PROGRAMMING 9. TRANSMITTERS 26 10. OPERATION OF YOUR OPENER 27 11. TEST SAFETY REVERSAL 27 12. TENSION ADJUSTMENT 13. 14. When LED is blinking the error message can be retrieved by pressing The total sum of numbers in blinking LEDs indicate so-called error number.
PAGE 3
18. TROUBLESHOOTING 3. IMPORTANT SAFETY INSTRUCTIONS Fault Cause Solution Indicator 8 does not glow. No power. Check mains supply. Thermal protection in transformer activated. Allow transformer to cool down. Defective control unit. Disconnect the electrical power. Remove lamp cover and housing. Unscrew control unit, pull slightly forward and withdraw the connecting plug. Remove control unit and have it checked. Indicator 6 flashes. Error 10 or 28 Automatic cut out set too sensitively.
PAGE 4
. TOOLS 17. EXTERNAL CONNECTIONS The instructions will refer to the tools shown below for proper installation, adjustment, and maintenance of the garage door opener. Additional tools may be required depending on your particular installation. Fig. 1 1 8 7 6 2 5 Wh 4 Str Str Pencil Drill and Drill Bits Tape Measure Wh Adjustable Wrench pur Stepladder Wire Cutters Ratchet and Sockets (1/2", 7/16") 5. GARAGE A garage door is a heavy moving object and can cause serious injury or death.
PAGE 5
. GARAGE (cont’d) 16. ACCESSORIES The following accessories are designed to provide added convenience, satisfaction and value to your door opener system. Accessories are available from your dealer. Check the type of door construction you have. The information contained in the figures below will be referred to later in the manual for proper installation on the different door types. Fig. 4 Sectional Door with Curved Track Fig.
PAGE 6
. OPENER PACKAGE CONTENTS 15. POWER HEAD ASSEMBLY (cont’d) The following items are included with your Garage Door Opener. All hardware components are located in the GDO carton. The accessories are packaged with their respective hardware in separate packs for ease of identification and use. Fig. 44 � � Items shown not actual size. Fig. 6 POWER HEADS �� EX-2005 (One-Light Opener) �� EX-2007 (Two-Light Opener) � �� Fig.
PAGE 7
. INSTALLATION STEPS 15. POWER HEAD ASSEMBLY Fig. 43 Identify a sound structural support on header wall above garage door for header bracket mounting. See Fig. 10. If appropriate header does not exist, replace or install a new support using a 50x100mm or 50x150mm (2x4 or 2x6) board. Fasten it securely using lag screws (not provided) to structural supports of garage. 6 4 1a 2a 1a 2a 3 7-1. MEASURE AND MARK DOOR AREA 1 2 See Fig.
PAGE 8
7-2. INSTALL HEADER BRACKET (cont’d) 14. RAIL ASSEMBLY Fig. 11 Ceiling  Mark pilot holes location on header through header bracket holes where lag screws will be inserted. IMPORTANT: See Fig. 10 for which header bracket holes to use.  Drill 3/16" pilot holes into header, and install bracket with lag screws (5/16 x 1-5/8”) provided.  Tighten lag screws firmly. NOTE: Follow the same procedure if header (shown in Fig.
PAGE 9
12. TENSION ADJUSTMENT Your preassembled rail comes with the tension adjusted to factory specifications. There should be no need for further adjustment. However, if exposed or subjected to unusually harsh operating conditions, the tension may need to be readjusted during the life of the opener. Fig. 38 Proper Tension Adjustment Rail End Stop (Header End) Tension Nut Washer Rail Fig. 39 Tab Location  Position 2 "C" brackets over rail and onto chassis.
PAGE 10
. OPERATION OF YOUR OPENER Fig. 17 Fig. 37 A. Transmitter Indicator Light Your opener can be activated via any of the following, depending on which accessories your opener system has:  Remote Control Transmitter  Wall Control Panel  Keyless Entry (optional accessory) C. Doorbell-Type Pushbutton Pushbutton B. Wall Control Panel REMOTE CONTROL TRANSMITTER: Fig. 17A Header Bracket Rail End-Stop 1/4 x 3-1/4" Clevis Pin Cotter Ring Opener Box 7-5.
PAGE 11
9. TRANSMITTERS TRANSMITTERS (Fig. 31): A family of state-of-the-art transmitters, each transmitter is custom encoded with installed battery. Offered in two styles to suit your personal preference.  Mini (2-or 4-channel)  Micro (3-channel) with keyring attachment. TRANSMITTER MOUNTING: The transmitters can be conveniently mounted inside your car using the visor clip or on the wall using the mounting plate. 7-7. MOUNT OPENER TO CEILING Fig.
PAGE 12
7-8. CONNECT ARM TO DOOR AND TROLLEY (cont’d) Level 4 Menu 3 Fig. 24 A. SECTIONAL DOORS:  Position curved door arm into door bracket channel so that short end of arm will be attached to door bracket. See Fig. 24. Curved door arm should be attached roughly at the same height as the top rollers of the door. SET EXTERNAL SIGNAL LIGHTS ( 5/16"-18x3/4" Hex Bolt Straight Door Arm 1. LED 2. Use  Position straight arm and curved arm to form an angle with the door (Fig.
PAGE 13
LEVEL 4 . SECURITY / SAFETY CONTROLS 7-10. INSTALL WALL CONTROL PANEL Set light(s) “on” time Set timed security cut out Set external signal lights Set opener lighting Set external relay alarm function Press for 10 seconds until LED Still hold the P button and press the 2. LED 3 3. Use  Mark hole location on wall. flasheds rapidly and all others are illuminated. button until LED blinks and all others are illuminated. Screw caps  Drill 1/16” pilot holes into wall.
PAGE 14
7-11. INSTALL LIGHT BULBS AND LENSES To prevent possible OVERHEATING of the end panel or light socket: • Use ONLY standard incandescent light bulb(s). • DO NOT use a bulb with a rating higher than 60 Watts (W). A stronger or larger bulb may result in fire or damage to the opener. To prevent possible radio frequency (RF) signal interference: • Do not use compact compact lighting (CFL). Fig. 30  Install a maximum 60 W incandescent bulb (not provided) into lamp socket(s).  Install lamp lens(es).
PAGE 15
8. OPENER PROGRAMMING LEVEL 3. AUTOMATIC CLOSING Attention: The opener has four (4) programming levels. For normal operation of the opener you only program the “open”, “closed” positions and the remote control in the Basic settings. Changes in the extended programming level may only be carried out by specialist. Attention: When using this feature a photo eye safety system must be connected and programmed in accordance with Level 2 Menu 1. Menu Overview: 1. 2. 3. 4. 8-1.
PAGE 16
Level 2 Menu 3 8-2. CONTROL PANEL SET MAXIMUM CLOSING FORCE The control panel is located under the control panel cover. Open the control panel by slightly pulling on the cover cutout, then allowing the cover to drop open. The hinges enable the cover to remain in place while you set the adjustments.
PAGE 17
LEVEL 2. ADVANCED SETTINGS 8-3. IMPORTANT INFORMATION Menu Overview 1. 2. 3. 4. 5. Attention: Before you start opener programming, make sure trolley is connected to chain or belt and door arm is attached to door.
PAGE 18
Menu 3 Advice: All menus can be reset by a RESET function to the original values set by factory. Reset is activated by pressing , and together for more than 30 seconds. 8-4. BASIC SETTINGS Menu Overview: PROGRAM THE TRANSMITTER CODE 1. LED blinks and all others are illuminated. 2. Press transmitter button until LED 3. Press to store multi-bit transmitter code and to finish basic programming. LEDs will automatically turn off starting at LED and ending at LED blinks rapidly. .