MODEL RTA-TS220L ASSEMBLY INSTRUCTIONS Thank you for purchasing one of our products. Please read carefully the assembly instructions before the installation. Do not discard this manual or any of the packaging material until the unit has been completely assembled.
P.2 RTA-TS220L P.
P.3 RTA-TS220L MAIN PARTS LAYOUT (FOR REFERENCE): SCREWS LIST: P.
P.4 RTA-TS220L P.4 BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS. ☛ Do a quick inventory to make sure the product contains all the parts and hardware. ☛ Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the CONTACT card included with the product. ☛ The replacement parts service is limited to the continental United States. If you reside in Hawaii, Puerto Rico, U.S.
P.5 RTA-TS220L P.5 ASSEMBLY STEPS Insert the studs (6) to the bottom of the leg structures (1) and (2), and to the corner of each base structure (3), (4) and (5) as shown. With the short frame structure (7) oriented as shown, attach the structures as indicated: 1st: Leg (1) to frame (7). 2nd: Base (3) to leg (1). 3rd: Leg (2) to base (3) and frame (7) as shown.
RTA-TS220L P.6 P.6 With the long frame structure (8) oriented as shown, attach the structures as indicated: 1st: Leg (1) to frame (8) on the right, and leg (2) to frame (8) on the left; 2nd: Base (4) to leg (1) on the right, and base (5) to leg (2) on the left. 3rd: Leg (2) to base (4) and frame (8) on the right, and leg (1) to base (5) and frame (8) on the left. PAY CLOSE ATTENTION TO THE ORIENTATION OF THE PARTS.
P.7 RTA-TS220L P.7 Using screws (A), secure the legs (1) and (2) to the bases (4) and (5), and to the frame (8) as shown. (This view shows the back side of the frame upside-down on the floor) Using screws (B), washers (F) and nut caps (E), assemble the frame (7) to frame (8) as shown. PAY CLOSE ATTENTION TO THE ORDER AND ORIENTATION OF THE HARDWARE.
P.8 RTA-TS220L P.8 With the tabletops (9) and (10) upside-down and oriented as shown, attach to them the brackets (11) using screws (A) as shown. (This view shows the tabletops upside-down on the floor) With the help of another person, place the frame from step 6 upside-down over the tabletops (9) and (10) making the holes coincide, then assemble the frame using screws (C) as shown. TO AVOID MISALIGNMENTS, FIRST SCREW LOOSELY AND TIGHTEN AFTER ALL THE SCREWS ARE IN PLACE.
RTA-TS220L P.9 P.9 Carefully and with the help of another person, turn the unit upright, then select the option of your preference: 🅐, 🅑 or 🅒, and attach the stand panels to the tabletops by inserting and tightening the screw knobs (12) into the supports from underneath as shown. VERY IMPORTANT: BEFORE ATTACHING, MAKE SURE THE SUPPORTS HAVE THE PROTECTORS INSERTED AS INDICATED IN STEP 9.
P.10 RTA-TS220L P.10 ☛ You have different options for the assembly of the accessory items on either side of the unit; install them according to your needs. Using screws (D), assemble on either side and from underneath the tabletops (9) and (10), the earphones hanger (15), the small cup holder (16), and the large cup holder (17). DONE! Before you start using, please read all the warnings in the next page.
P.11 P.11 RTA-TS220L AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING CARE AND MAINTENANCE WARNINGS: WEIGHT LIMITS 130 Lbs. (60 Kg) 11 Lbs. (5 Kg) 130 Lbs. (60 Kg) 3.25 Lbs. (1.5 Kg) 3.25 Lbs. (1.5 Kg) 3.25 Lbs. (1.5 Kg) •Do not exceed the indicated weight limits. •Do not expose the surfaces to direct sunlight or to extreme environmental conditions. •Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and water, then dry with a clean towel.
