Power Head “E” System Owners Manual and Safety Instructions © 2006 Mantis, Div. of Schiller-Pfeiffer Inc. All Rights Reserved.
Table of Contents Important Information Specifications . . . . . . . . . . . . . . . . . . . . . . .4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 Special Safety Information . . . . . . . . . . . . . . . .1 Assembly Instructions . . . . . . . . . . . . . . .4 Parts Explosion . . . . . . . . . . . . . . . . . . . . .5 Safety and Warnings Safety Decals . . . . . . . . . . . . . . . . . . . . . . . . . .2 General Safety Rules . . . . . . . . . . . . . . . . . . . .2 Parts List . .
SAFETY SYMBOLS IDENTIFICATION What the symbols mean: 1. Read the instructions. 1 2 3 4 2. Do not expose to rain. 3. Remove plug from main (electric power source) immediately if cable is damaged or cut. 4. Double insulated. Service Information Contact If you have questions about any topic in this Manual, or for the name of your local dealer, call 1-800-366-6268 toll free, Monday - Friday, 8:00 a.m. to 5:30 p.m., Eastern Time, or ask for Customer Service.
12. Disconnect tools. When not in use, before servicing and when changing accessories such as blades, bits and cutters. 13. Remove adjusting keys and wrenches. Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on. 14. Avoid unintentional starting. Do not carry a plugged in tool with a finger on the switch trigger. Ensure switch is off when plugging in. 15. Use outdoor extension leads.
33. Maintain a firm footing and good balance, do not overreach while trimming. Before you start to trim, check the work area for obstacles that might cause you to lose your footing, balance or control of the machine. While operating the machine always be sure of a safe and secure operating position especially when using steps or a ladder. Always be sure of your footing on slopes. WARNING – 35. Securing the extension cord. Bend the extension cord about 15 inches from the plug end.
c) Drive in the four screws supplied, starting with the bottom two screws. Do not tighten screws. d) Adjust handle location to your preference, and then tighten all screws. D. Brush Replacement Brush of the motor is replaceable. Brush has to be replaced after approximately 150 hours of use. The life of the brush depends on the use of the unit and may last much longer. Do not replace it yourself. Contact Mantis Customer Service for brush replacement.
Power Head Parts List KEY # DESCRIPTION PART # QTY 1 MOTOR ASSEMBLY 331252 1 2 MOTOR BRUSH 331253 3 BRUSH HOLDER 4 DESCRIPTION PART # QTY 29 CASING (LEFT) 331276 1 2 30 SCREW ST4,2X16 331564 8 331254 2 31 INLAY (LEFT) 331277 1 HOLDER 331255 2 32 WIRE JOINTER 331278 1 5 SCREW ST2,9X10 331556 4 33 POWER CORD 331279 1 6 SHUTTER 331256 2 34 EXTENSION CORD CLIP 331280 1 7 REV CONTROLLER 331257 1 35 SCREW M5X35 331565 4 8 SCREW ST3,5X13 331557 2 3
2 YEAR LIMITED SERVICE & WARRANTY POLICY FOR ELECTRIC POWER HEAD “E” SYSTEM MANTIS extends this limited warranty against defects in material and workmanship for a period of two years from the date of purchase, to the first retail purchaser and each subsequent owner during the warranty period. This warranty covers all portions of the Mantis Electric Power Head “E” System.
