Jean Louis MENEGON Représentant et Conseiller Région Sud Ouest Tel : 06 76 08 96 83 Email: jlouismenegon@aol.com www.menegon-metrologie.
INTRODUCTION Health & Safety INTRODUCTION Vision Engineering and its products conforms to the requirements of the EC Directives on Waste Electrical and Electronic Equipment (WEEE) and Restriction of Hazardous Substances (RoHS). Jean Louis MENEGON - Votre représentant et Conseiller - tél : 06 76 08 96 83 Email: jlouismenegon@aol.com - web: www.menegon-metrologie.
CONTENTS SYSTEM DIAGRAMS CONTENTS Mantis Compact 1 Mantis Elite 2 OBJECTIVE SPECIFICATIONS Mantis Compact 3 Mantis Elite 3 OPTIONS & ACCESSORIES Parts table 4 MAINTENANCE & SPARE PARTS Mantis Compact Replacing the desiccant Replacing the LED array 5 5 5 Mantis Elite Replacing the desiccant Replacing the LED array Elite turret replacement Elite pivot retrofit 6 6 6 7 9 Mantis universal arm baseplate mounting dimensions 10 Spare parts 11 TROUBLESHOOTING COMPACT & ELITE 12 Checking the univ
SYSTEM DIAGRAMS SYSTEM DIAGRAMS Mantis Compact Jean Louis MENEGON - Votre représentant et Conseiller - tél : 06 76 08 96 83 Email: jlouismenegon@aol.com - web: www.menegon-metrologie.com www.visioneng.
2 Mantis Service Manual EPI Illuminator MEI 001 Mantis Elite Head Assembly MEH-001 Anti Glare Hood 202-D0479 Mantis Elite Bench Stand MES-006 converging lens) MEO-002 x2 MEO-006SL x6 Dust Cover MS-003 - Mantis with Universal Stand MS-004 - Mantis with Bench Stand Objective x15 x10 Lenses Substage MEO-004 x4 LED Array MEO-006 x6 MELED-003 MEO-008 x8 x20 MEO-010 x10 x6 x8 Floating MEO-015 x15 Power x4 Stage MEO-020 x20 X6 SLWD Supply MS-001 MPS-001 (UK) Objective x2 MPS-002 (USA/Japan/Asia) Lenses MPS-
OBJECTIVE SPECIFICATIONS OBJECTIVECompact Mantis SPECIFICATIONS Objective Lenses Part Number Working Distance Field of View Depth of Field X2 MCO-002 167mm / 6.57" 45.0mm / 1.77" 45.0mm X4 MCO-004 96mm / 3.78" 27.5mm / 1.08" 27.5mm X6 MCO-006 73mm / 2.87" 19.2mm / 0.76" 19.2mm Mantis Elite Objective Lenses Part Number Working Distance Field of View Depth of Field X2 MEO-002 160mm / 6.29" 57.0mm / 2.24" 57.0mm X4 MEO-004 96mm / 3.78" 34.0mm / 1.34" 34.
OPTIONS & ACCESSORIES OPTIONStable Parts & ACCESSORIES Part Name 4 Part Number Mantis Floating Stage MS-001 Compact X4, X6 Disposable Lens Protections Caps (4-pack) MCO-010 Elite Disposable Lens Protection Caps for X4, X8, X10 (4-pack) MEO-025 Elite Disposable Lens Protect Caps for X6 (4-pack) MEO-026 Dessicant, 10-pack (Blue good; Pink replace) M006 Picture Jean Louis MENEGON - Votre représentant et Conseiller - tél : 06 76 08 96 83 Mantis Service Manual Email: jlouismenegon@aol.
MAINTENANCE & SPARE PARTS MAINTENANCE Mantis Compact & SPARE PARTS Replacing the desiccant (see the diagram below): u Disconnect the power cord from the back of the head. u Remove the screw securing the desiccant cover and remove the cover u. u Replace the desiccant and reinstall the cover. u Reconnect the power cord at the back of the head. Note: If the desiccant is pink it needs to be replaced. Useable desiccant is blue.
MAINTENANCE & SPARE PARTS Mantis Elite Replacing the desiccant (see the diagram below): u Disconnect the power cord from the back of the head. u Remove the grommet u covering the desiccant and remove the desiccant. u Install fresh desiccant and replace the grommet. u Reconnect the power cord at the back of the head. Note: If the desiccant is pink it needs to be replaced. Useable desiccant is blue.
MAINTENANCE & SPARE PARTS Elite turret replacement Required Tools: #1 Phillips screwdriver u Remove any objective lenses that may be installed in the turret. u Uninstall the Mantis Head from the stand. u Rest the viewing head upside down (objective turret facing up). Be sure to secure the head so that it does not roll off of the work bench (a small, empty cardboard box works well). u Ensure the objective lens securing screws u are fully screwed in (but not too tightly).
MAINTENANCE & SPARE PARTS u Remove all three screws on the inside of the turret. Note: u Remove the old turret and replace with the new turret. u Replace all three screws. Note: 8 the front screw has a washer. do not over tighten. u Reinstall the head to the stand. u Reinstall the objective lenses. u Verify that the new turret rotates smoothly. Jean Louis MENEGON - Votre représentant et Conseiller tél : 06 76 08 96 83 MantisEmail: Service Manual jlouismenegon@aol.com - web: www.
MAINTENANCE & SPARE PARTS Elite pivot retrofit Note: Read all the following instructions before commencing work. u Isolate the Mantis from mains power. u Unscrew the left-hand side handle u and discard. u v u Release the rubber gaiter v from the groove in the head unit and peel back to expose the head mounting screws. u Using a flat-bladed screwdriver, remove the lower head mounting screw w completely.
MAINTENANCE & SPARE PARTS u Remove the lower head mounting bolt and then, ensuring the upper bolt is tight, back it off 2 complete revolutions. u Hang the head and tighten both head mounting bolts. u Seat the rubber gaiter bacl into the groove in the head. u Thread on the large handle | and screw it in. u Plug the mains adapter into the mains supply and connect the head power cable into the head. u The Mantis is now ready for use. | Mantis universal arm baseplate mounting dimensions 75mm dia.
MAINTENANCE & SPARE PARTS Spare parts 202-A0073 Mantis Arm Clamp Assembly (with G-clamp) 202-B0248 Mantis Bench Stand stage glass 202-B0316 Mantis Elite Anti-Glare Shield. 202-D0479 Elite viewing mask to shield ambient light from the viewing lens.
TROUBLESHOOTING COMPACT & ELITE TROUBLESHOOTING Problem LEDs not lit. Possible Solution * Verify power supply is plugged into the stand and into the power outlet (utility power). * Verify On/Off switch on stand is turned On. * Verify that the power cord in the back of the head is plugged in. * Verify that the power supply is functioning correctly. (Use a multimeter to measure the output voltage or try using a spare power supply.
TROUBLESHOOTING Checking the universal stand on/off switch connections u Shown to the right, is the On/Off switch installed in the Universal Stand. u Using a small flat blade screwdriver, gently pry the switch out. u Once the switch is loose, pull it out using your fingers. u Verify that both wires are properly connected (the switch shown has one wire disconnected). u With both wires connected, reinstall the switch by gently pressing it back into place.
SERVICE Address SERVICE If after using the information provided in this manual, the Mantis product you are working with needs additional repair, please contact: Vision Engineering Monument House Monument Way West Woking Surrey GU21 5EN Tel: Fax: +44 (0) 1483 248300 +44 (0) 1483 248301 Email: generalinfo@visioneng.com Serial number locations Location of Mantis Head serial number label. Location of Mantis Universal Stand serial number label. Location of Mantis Bench Stand serial number label.
WARRANTY WARRANTY This product is warranted to be free from defects in material and workmanship for a period of one year from the date of invoice to the original purchaser. If during the warranty period the product is found to be defective, it will be repaired or replaced at facilities of Vision Engineering or elsewhere, all at the option of Vision Engineering.
For more information... LIT 4176 R1.0/02/08 Vision Engineering has a network of offices and technical distributors around the world. For more information, please contact your Vision Engineering branch, local authorised distributor, or visit our website. Vision Engineering Ltd. (Manufacturing) Send Road, Send, Woking, Surrey, GU23 7ER, England Tel: +44 (0) 1483 248300 Fax: +44 (0) 1483 223297 Email: generalinfo@visioneng.com Vision Engineering Inc.
