Technical Specifications

Form No. M6039 Printed in U.S.A. 4/07
© 2007 Mansfield Plumbing Products, LLC
® Pro-fit is a registered trademark
of Mansfield Plumbing Products, LLC.
Optional Removable Apron
Pump locations are shown for clarity. STD-standard pump location.
ALT1-alternate pump location.
Note: If a factory installed nailing flange is added to a unit,
add 1/8" to each side flanged.
Note: Measurements may vary 1/4" (6.4 mm +_)
Dimensions 59-3/4" x 59-3/4" x 21-1/4"
Material Acrylic, fiberglass reinforced
Construction Self-contained, pre-plumbed whirlpool bath,
mounted on a pre-leveled thermoformed base
Pump Motor 1-1/4 HP, 1 phase, 120 volt, 60 HZ, factory installed
Electrical Requirements 120 volt, 20 AMP, GFCI
Inline Heater 1.5 KW, 12.5 AMP, 110 volt
Number of Jets Six
Air Volume Control Two
Water Capacity 85 gal. max., 60 gal. min.
(323 liters/228 liters)
Floor Loading 47 lbs./sq. ft. (229 kg/m
2
)
Shipping Weight 167 lbs. (76 kg)
Warranty Limited One Year
Drain
Air Switch
Air Control
Jets
Suction
ALT1
STD
32"
(813 mm)
59-3/4"
(1518 mm)
57-1/2"
(1461 mm)
22-1/4"
(565 mm)
52-1/2"
(1333 mm)
84"
(2134 mm)
21-1/4"
(540 mm)
19-3/4"
(502 mm)
59-3/4"
(1518 mm)
18"
(457 mm)
22-1/4"
(565 mm)
21-1/4"
(540 mm)
19-3/4"
(502 mm)
52-1/2"
(1333 mm)
84"
(2134 mm)
Recessed Toe Space
Centerline
Overflow
22-1/4"
(565 mm)
59-3/4"
(1518 mm)
32"
(813 mm)
Slope
1/4”/Foot
(6 mm)/Foot
22-1/4"
(565 mm)
SPECIFICATIONS
TECHNICAL INFORMATION
6060
Corner Whirlpool or Bath
UPGRADES
These dimensions are nominal and are subject to change without notice.
When tested for compliance to the requirement of ANSI A112.19.7M and A112.19.8M for “Whirlpool
Bath Appliances” and ANSI Z124 for “Plastic Bathtub Units” the tested units are found to comply and
are acceptable for listing under the Terralab Engineers, Inc. follow-up service. Listed Number 15197.
Certified for permanent electrical supply connection only.
Factory Installed In-line Heater
• A reliable, heating control upgrade maintains
water temperature at desired level and
operates when flow of water is detected in
the system.
Nailing Flange Kit
• Code approved kit featuring flange
material, sticky tape and instructions.
• Makes watertight installation easy
and secure.
Trim Upgrade
• This option allows an upgrade to Chrome or Everbrass (PVD)
trim including jets, intake, control and air controls.
Lift & Turn Drain Kit
Chrome and Everbrass (PVD)
• The lift and turn drain kit provides simple and easy
draining of the bathtub.
Factory Installed Nailing Flange
• Code approved nailing flange option makes
watertight installation easy and secure.
Removable Apron - Corner Model
• This upgrade provides quick and easy access
through removable apron to whirlpool pump
and interior parts. Available on selected models,
check specific model upgrade listing.
PROFIT Specs 4/9/07 1:22 PM Page 2