Technical Specifications
Form No. M6021 Printed in U.S.A. 4/07
© 2007 Mansfield Plumbing Products, LLC
® Pro-fit is a registered trademark
of Mansfield Plumbing Products, LLC.
Optional Removable Apron
Note: If a factory installed nailing flange is added to a unit,
add 1/8" to each side flanged.
Note: Measurements may vary 1/4" (6.4 mm +_)
Dimensions 35-1/2" x 71-1/2" x 20"
Material Acrylic, fiberglass reinforced
Construction Self-contained, pre-plumbed whirlpool bath
Pump Motor 1-1/4 HP, 1 phase, 120 volt, 60 HZ, 5.9 AMP,
Electrical Requirements 120 volt, 20 AMP, GFCI
Number of Jets Six
Air Volume Control Tw o
Water Capacity 52 gal. max., 27 gal. min.
(198 liters/103 liters)
Floor Loading 47 lbs./sq. ft. (229 kg/m
2
)
Shipping Weight 154 lbs. (70 kg)
Warranty Limited One Year
STD
ALT 2
Drain
Air Switch
A
ir C
o
ntrol
Jets
Suction
ALT1
18
1
/4
"
Centerline
Overflow
35-1/2"
(902 mm)
12"
(305 mm)
71-1/2"
(1816 mm)
62"
(1575 mm)
48"
(1219 mm)
20"
(508 mm)
27"
(686 mm)
20"
(508 mm)
20"
(508 mm)
35-1/2"
(902 mm)
15-1/2"
(394 mm)
18-1/2"
(470 mm)
71-1/2"
(1816 mm)
16-1/4"
(413 mm)
Slope
1/4”
/Foot
(6 mm)/Foo
t
SPECIFICATIONS
TECHNICAL INFORMATION
3672 ALTO
Rectangular Whirlpool or Bath
UPGRADES
These dimensions are nominal and are subject to change without notice.
When tested for compliance to the requirement of ANSI A112.19.7M and A112.19.8M for “Whirlpool
Bath Appliances” and ANSI Z124 for “Plastic Bathtub Units” the tested units are found to comply and
are acceptable for listing under the Terralab Engineers, Inc. follow-up service. Listed Number 15197.
Certified for permanent electrical supply connection only.
Factory Installed Nailing Flange
• Code approved, nailing flange option makes
watertight installation easy and secure.
Removable Apron - 6 ft. Model
• This upgrade provides quick and easy access
through removable apron to whirlpool pump
and interior parts. Available on selected models,
check specific model upgrade listing.
Factory Installed In-line Heater
• A reliable, heating control upgrade maintains
water temperature at desired level and
operates when flow of water is detected in
the system. Features a standard plug for
easy electrical connection (GFCI: 120V, 20 amp dedicated circuit
required to power this heater).
Trim Upgrade
• This option allows an upgrade to Chrome or Everbrass (PVD) trim
including jets, intake, control and air control(s).
Lift & Turn Drain Kit
Chrome and Everbrass (PVD)
• The lift and turn drain kit provides simple and easy
draining of the bathtub.
Nailing Flange Kit
• Code approved kit featuring flange
material, sticky tape and instructions.
• Makes watertight installation easy
and secure.
Pump locations are shown for clarity. STD-standard pump location.
ALT1 and ALT2-alternate pump locations are optional.
PROFIT Specs 4/9/07 1:22 PM Page 8