AJ-64 RACK CONVEYOR DISHMACHINES S E R V I C E MODELS COVERED IN THIS MANUAL: AJ-64CE (ELECTRICALLY-HEATED) AJ-64CS (STEAM-HEATED) M A N U A L March 7, 2003 P/N 7610-002-30-93 (Revision A) www.jacksonmsc.
TABLE OF CONTENTS SECTION I. DESCRIPTION PAGE GENERAL SECTION Specifications 1 INSTALLATION & OPERATION SECTION Installation Instructions Operating Instructions 2 3 III. TROUBLESHOOTING SECTION 4 IV. DIMENSIONS 6 V.
SPECIFICATIONS of the AJ-64CE/AJ-64CS RACKS PER HOUR: AJ-64CE: AJ-64CS: ELECTRICAL REQUIREMENTS: 287 287 AJ-64CE (ALL ARE 60 HZ FREQUENCY): VOLTS PHASE APPROX. AMPS 208 230 SINGLE SINGLE 140 AMPS 128 AMPS 208 230 460 THREE THREE THREE 82 AMPS 76 AMPS 38 AMPS DISHES OR GLASSES PER HOUR: AJ-64CE: AJ-64CS: 7200 7200 WASH TANK CAPACITY (GALLONS): AJ-64CE: AJ-64CS: 15.4 15.
INSTALLATION INSTRUCTIONS Jackson MSC Inc. provides technical support for all of the dishmachines detailed in this manual. We strongly recommend that you refer to this manual before making a call to our technical support staff. Please have this manual with you when you call so that our staff can refer you, if necessary, to the proper page. Technical support is avaliable from 8:00 a.m. to 5:00 p.m. (EST), Monday through Friday. Technical support is not available on holidays.
INSTALLATION INSTRUCTIONS (CONTINUED)/OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS CHEMICAL FEEDER EQUIPMENT: Detergent may be introduced into the unit through the removal of the bulkhead plug in the rear of the tub and replacing it with the third party detergent injection fitting. Remove the bulkhead plug in the side of the tub to install the detergent concentration probe. PREPARATION: Before proceeding with the start-up of the unit, verify the following: 1. Close door(s) on dishmachine.
TROUBLESHOOTING SECTION Problem: Nothing on dishmachine operates. The power switch is ON and the power indicator light is OFF. 1. Machine is not wired correctly to incoming power source. Have an electrician verify wiring. 2. Machine circuit breaker is tripped. Reset the circuit breaker. If it trips again, contact an electrician to verify the machine amp draw. 3. Service breaker is tripped. Reset the service breaker. If it trips again, contact an electrician to verify the machine amp draw.
TROUBLESHOOTING SECTION (CONTINUED) Problem: Spotting of silverware, glasses and dishes. 1. Incorrect final rinse temperature. Verify that the rinse water temperature matches that which is listed on the machine data plate. 2. Clogged wash and/or rinse nozzles and arms. Remove the arms and verify that they and their nozzles are from debris. 3. Excessively hard water. Install a water softener to reduce hardness. 4. Loss of water pressure due to clogged/obstructed wash pump.
DIMENSION PAGES LEGENDS/TABLE DIMENSIONS The following pages contained dimensioned drawings to be used as references when installing your machine. The drawings also have several key points indicated , which can be referenced using the table below: LETTER DESCRIPTION A Electrical Connection - See Data Plate for Amperage Requirements B Water Inlet - 3/4” I.P.S. 180°F Water Required C Drain Connection - 1-1/2” I.P.S.
TOP VIEW AJ-64 DIMENSIONS 7
19 22 18 23 21 17 20 16 15 15 14 13 10 12 11 9 6 8 7 5 4 3 2 1 CONTROL BOX ASSEMBLY 8
CONTROL BOX ASSEMBLY (CONTINUED) ITEM 1 2 3 QTY 1 1 1 1 1 12 3 13 14 15 16 17 18 19 20 21 22 23 1 1 0 1 1 1 0 3 1 1 1 DESCRIPTION Electrical Box Weldment Electrical Box Inner Panel Decal, Copper Conductors Only Decal, Guage, AJ-64 Terminal Block Decal, L1-L2-L3 Ground Lug Decal, Ground Light, Amber (Not used on steam models) Light, Red Not Applicable for AJ-64 Models Not Applicable for AJ-64 Models Circuit Breaker (208-230 volt models) Power Switch Overload, 1-1.
1 2 4 6 5 7 3 6 12 17 8 9 2 5 5 13, 14 4 6 13 18 17 7 8 6 9 20 22 10 14, 15, 16 10 21 22 11 8 9 6 7 6 5 4 12 5 9 19 INCOMING PLUMBING ASSEMBLY 10
INCOMING PLUMBING ASSEMBLY (CONTINUED)/WPRK PLUMBING OPTION ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 QTY 1 2 3 3 5 6 3 3 4 2 1 2 2 2 1 1 2 1 1 1 1 2 DESCRIPTION Injector, Rinse Weldment Fill Line, Injector Plug, 1/8” NPT, Brass Vacuum Breaker, 3/4” NPT, Brass Elbow, 3/4” NPT, Street, Brass Nipple, 3/4” NPT, Close, Brass Valve, Solenoid, 3/4” NPT, 110 Volt Union, 3/4” NPT, Brass Adapter, 3/4” Male Tee, Copper, 3/4” CU x CU x CU Tube, Copper, 3/4” x 3” Long Nipple, 3/4” NPT, Brass, 6” L
EXTERNAL ELECTRIC BOOSTER OPTION INCOMING PLUMBING 2 5 Plumbing with Water Hammer Arrestor 1 6 7 11 3 ITEM 1 2 3 4 5 6 7 8 9 10 11 QTY -------------------------------------------------------- 4 3 2 DESCRIPTION Y-Strainer, 3/4” NPT, Brass Adapter, 3/4” Male Tube, Copper, 3/4” x 3-7/16” Long Tee, Copper, 3/4” x 3/4” x 1/2” Arrestor, 1/2” NPT, Water Hammer Adapter, 1/2” NPT x Male Regulator, Pressure, 3/4” NPT, Brass Nipple, 3/4” NPT x 2” Long, Brass Elbow, Brass, 90 Degree, 3/4” Nipple, 3/4”, Bras
EXTERNAL ELECTRIC BOOSTER OPTION OUTLET PLUMBING 6 9 8 7 6 4 5 2 3 ITEM 1 2 3 4 5 6 7 8 9 1 QTY 1 1 1 1 1 2 1 1 1 DESCRIPTION Elbow, Brass, 90 Degree, 3/4” Nipple, 3/4” NPT x 2” Long, Brass Union, 3/4” NPT, Brass Adapter, 3/4”, Male Tube, Copper, 3/4” x 24” Long Elbow, 3/4” Copper to Copper (Female) Tube, Copper, 3/4” x 49-1/2” Long Elbow, 3/4”, 90 Degree Street, Copper to Copper Tube, Copper, 3/4” x 5-7/8” Long 13 Mfg. No.
3/4” SOLENOID VALVE & 3/4” NPT VACUUM BREAKER REPAIR PARTS KITS Screw Data Plate Cap Screw Coil & Housing Data Plate Valve Bonnet Spring position is moved for clarity. Goes below the plunger. Spring 4810-200-04-18 Cap Plunger 4810-200-04-18 O-Ring 4810-100-10-18 Cap Retainer Diaphragm Retainer O-Ring Diaphragm 4810-100-10-18 Plunger COMPONENTS OF REPAIR KIT 4820-001-60-57 Screen Retainer Body Mesh Screen Valve Body Complete 110 Volt Solenoid Valve Assembly Mfg. No.
STEAM INLET PLUMBING ASSEMBLY 10 9 7 8 11 12 15 16 15 6 TOP VIEW 2 1 3 14 FRONT VIEW 4 5 11 11 11 15 12 13 9 9
STEAM INLET PLUMBING ASSEMBLY (CONTINUED) ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 QTY 1 1 1 1 1 1 2 6 4 1 4 5 1 1 2 2 DESCRIPTION Valve, 1” Gate Nipple, 1” NPT, Close, Black Iron Y-Strainer, 1” NPT, Black Iron Reducer, 1” NPT to 3/4” NPT Nipple, 3/4” NPT x 6” Long, Black Iron Tee, 3/4” x 3/4” x 3/4”, Black Iron Nipple, 3/4” NPT x 4” Long, Black Iron Elbow, Street, 3/4” NPT, 90 Degree, Black Iron Elbow, 3/4” NPT, 90 Degree, Black Iron Nipple, 3/4” NPT x 7” Long, Black Iron Union, 3/4” NPT, Black Iron N
STEAM OUTLET PLUMBING ASSEMBLY (BOTTOM) 6 7 3 4 5 1 2 ITEM 1 2 3 4 5 6 7 QTY 1 2 1 1 1 1 1 2 DESCRIPTION Nipple, 3/4” NPT x 18” Long, Black Iron Elbow, 90 Degree, Street, 3/4” NPT, Black Iron Elbow, 90 Degree, 3/4” NPT, Black Iron Reducer, 3/4” NPT to 1/2” NPT Union, 3/4” NPT, Black Iron Nipple, Close, 3/4” NPT Steam Trap, 3/4” NPT 17 Mfg. No.
STEAM OUTLET PLUMBING ASSEMBLY (TOP) 1 2 ITEM 1 2 3 4 5 6 7 QTY 1 1 1 1 1 1 1 3 7 4 5 DESCRIPTION Steam Trap Nipple, Close, 3/4”, Black Iron Union, 3/4” NPT, Black Iron Elbow, Street, 90 Degree, Black Iron Nipple, 3/4” NPT x 22” Long, Black Iron Elbow, 90 Degree, 3/4” FNPT, Black Iron Reducer, 3/4” NPT x 1/2” NPT 18 6 Mfg. No.
DRAIN PLUMBING ASSEMBLY 1 7 5 4 3 9 2 8 8 2 10 NOTE 1 7 6 6 ITEM 1 2 3 4 5 6 7 8 9 10 3 4 QTY 2 3 4 4 2 2 2 2 1 1 2 3 4 DESCRIPTION Ball Valve Handle Assembly Tee, Brass, 1-1/2” x 1-1/2” x 1-1/2” Adapter, 1-1/2” Tube, Copper, 1-1/2” OD x 2” Long Connector, No-Hub, 1-1/2” Elbow, 1-1/2”, Street, Brass, 90 Degree Valve, Ball, 1-1/2” NPT Nipple, 1-1/2” NPT, Brass, Close Rinse Nipple Weldment Fitting, Barbed, 1-1/2” NPT x 1-1/2” 5 4 3 1 Mfg. No.
DRAIN HANDLE WELDMENT ASSEMBLY/FRAME WELDMENT 1 2 4 3 ITEM 1 2 3 4 QTY 1 1 1 1 DESCRIPTION Ball Valve Handle Weldment Locknut, 1/4”-20 with Nylon Insert Spacer Screw, 1/4”-20 x 2” Long Hex Head Mfg. No. 5700-021-70-42 5310-374-01-00 5700-000-01-53 5306-011-84-72 FRAME WELDMENT 1 2 Item 1: Model AJ-64CE/AJ-64CS Left to Right P/N 5700-002-73-00 Right to Left P/N 5700-0002-73-00 Item 2: Bullet Feet (4 per model) - order using part number 5340-011-71-74.
HEATER BOX/THERMOSTATS AJ-64 Heater Box Cover 5700-031-81-61 AJ-64 Heater Box Weldment 5700-002-41-18 Terminal Board 5940-021-70-70 Thermostat, High Limit, 104 Degrees C 5930-121-71-36 Thermostat, Wash Regulating, 78 Degrees C 5930-121-67-72 Decal, High Limit Thermostat 9905-011-84-31 Thermostat Bracket 5700-011-73-72 Decal, Wash Regulating Thermostat 9905-011-84-31 21
MOTORS/MOTOR SUPPORT BRACKET ASSEMBLY The chart below details the part numbers for the various models covered in this manual. Refer to the machine data plate for voltage and phase information.
STEAM COIL ASSEMBLY Complete Steam Coil Assembly 5700-041-88-31 Stand C, Steam Coil Support 5700-002-74-84 Steam Coil Weldment 5700-031-88-30 Stand D, Steam Coil Support 5700-002-74-85 Stand B, Steam Coil Support 5700-002-74-83 Stand A, Steam Coil Support 5700-002-74-82 Gasket, Steam Coil 4 per assembly 5700-001-17-86 Washer, Steam Coil 2 per assembly 5700-001-17-87 Adapter, Steam Coil Nut 2 per assembly 5700-011-17-85 23
WASH PUMP ASSEMBLY 15 10 8 1 4 7 12 14 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 QTY 1 1 1 4 1 1 4 1 1 1 1 1 1 1 2 13 11 9 6 5 DESCRIPTION See Page Entitled “Pump Support Bracket Assembly” Hose Clamp, 4-1/8” - 7”, HSS104 See Page Entitled “Motors” Nut, Hex, 3/8”-16, S/S Pump Plate Pump Seal Bolt, 3/8”-16 x 2” Long Hex Head Key, 3/16” x 1” Long Impeller Impeller Washer Bolt, 1/4”-20 x 3/4” Long Pump Manifold Hose See Page Entitled “Assorted Gaskets” See Page Entitled “Pump Weldments” Hose Clamp
PUMP WELDMENTS Wash Pump Weldment 5700-031-81-47 Power Rinse Pump Weldment 5700-041-68-88 The gasket used to seal the weldment to the tub can be found on the page entitled “Assorted Gaskets”.
ASSORTED GASKETS Motor Mounting Gasket 5330-011-71-62 Heater Gasket 5330-200-02-70 Rinse Assembly Vellumoid Gasket 5330-111-42-81 Rinse Drain Plate Gasket 5330-011-72-27 Pawl Bar Gutter Gasket 5330-011-68-55 26
HEATERS/HOOD WELDMENTS/TUB WELDMENTS/WASH MANIFOLD Order your wash heaters using the table below: Model Volts Phase KW Part Number AJ-64CE AJ-64CE AJ-64CE AJ-64CE AJ-64CE AJ-64CE AJ-64CE AJ-64CE AJ-64CE 208 208 230 230 208 208 230 230 460 1 1 1 1 3 3 3 3 3 10 15 10 15 10 15 10 15 10 4540-121-76-91 4540-121-68-45 4540-121-76-92 4540-121-68-46 4540-121-91-76 4540-121-68-45 4540-121-76-92 4540-121-68-46 4540-121-76-93 Vent Cowl Cover Weldment 5700-011-74-67 Top Gasket 5330-031-83-47 Side Gasket 5330-
UPPER WASH ARM ASSEMBLY 1 2 3 4 5 6 SERVICE NOTE: When replacing the 10-32 screws in the End Caps, it is recommended that a thread locking fluid be used to ensure that the screws do not back out during normal operation. ITEM 1 2 3 4 5 6 QTY 3 3 3 3 1 1 1 DESCRIPTION Screw, 10-32 x 3/8” Long Lanyard Locknut, 10-24 with Nylon Insert End Cap Upper Wash Arm Manifold Weldment Cap, Wash Tube Entire Assembly 28 Mfg. No.
LOWER WASH ARM ASSEMBLY 4 1 2 3 5 6 SERVICE NOTE: When replacing the 10-32 screws in the End Caps, it is recommended that a thread locking fluid be used to ensure that the screws do not back out during normal operation. ITEM 1 2 3 4 5 6 QTY 6 6 6 6 1 1 DESCRIPTION Screw, 10-32 x 3/8” Long Lanyard Locknut, 10-24 with Nylon Insert End Cap Lower Wash Arm Manifold Weldment Manifold Quick-Release Key Entire Assembly 29 Mfg. No.
UPPER POWER RINSE ARM ASSEMBLY SERVICE NOTE: When replacing the 10-32 screws in the End Caps, it is recommended that a thread locking fluid be used to ensure that the screws do not back out during normal operation. 4 5 3 2 ITEM 1 2 3 4 5 6 1 QTY 1 3 3 3 3 1 6 DESCRIPTION Upper Wash Manifold End Cap Lanyard Screw, 10-32 x 3/8” Long Locknut, 10-24 with Nylon Insert Cap, Wash Tube Entire Assembly 30 Mfg. No.
LOWER POWER RINSE ARM ASSEMBLY 2 5 ITEM 1 2 3 4 5 6 1 QTY 1 6 6 6 6 1 SERVICE NOTE: When replacing the 10-32 screws in the End Caps, it is recommended that a thread locking fluid be used to ensure that the screws do not back out during normal operation. 4 DESCRIPTION Lower Wash Arm Manifold End Cap Locknut, 10-24 with Nylon Insert Lanyard Screw, 10-32 x 3/8” Long Manifold Quick Release Key Entire Assembly 31 3 6 Mfg. No.
FINAL RINSE ASSEMBLY 3 1 2 Upper Rinse Arm Assembly End plugs can be ordered using part number 4730-209-07-37. 5 4 Lower Rinse Arm Assembly * - Indicates an item not shown ITEM 1 2 3 4 5 6* 7* QTY 1 1 4 1 4 2 2 DESCRIPTION Final Rinse Manifold Weldment Upper Rinse Arm with Nozzles Upper Rinse Arm Nozzles Lower Rinse Arm with Nozzles Lower Rinse Arm Nozzles O-Ring (Not Shown) Ring, Retaining, Rinse Head Bushing (Not Shown) 32 Mfg. No.
DRIVE ASSEMBLY 7 9 3 1 8 2 4 5 6 ITEM 1 2 3 4 5 6 7 8 9 QTY 2 1 1 1 1 2 1 2 1 DESCRIPTION Pillow Block Drive Socket Drive Rod Plate Adjuster Crank Assembly Adjuster Skotch Yoke Weldment Coupling and Expansion Leg Weldment Pawl Bar Drive Linkage Casting Shaft Collar Spacer Plate 33 Mfg. No.
DRIVE ASSEMBLY (CONTINUED) 1 5 3 2 6 12 ITEM 1 2 3 4 5 6 QTY 1 1 1 2 2 1 4 DESCRIPTION Drive Plate and Rod Weldment Adjuster Spring Drive Motor Mounting Bracket Shaft Collar Pillow Block Drive Spring 34 Mfg. No.
DRIVE ASSEMBLY (CONTINUED) 4 2 5 8 7 6 1 3 35
DRIVE ASSEMBLY (CONTINUED) ITEM 1 2 3 4 5 6 7 8 QTY 1 1 1 1 1 1 2 1 DESCRIPTION Key Adjusting Handle Weldment Drive Hub Drive Motor Gear Drive Roller Bearing Washer, 1/2”, Flat Set Screw Mfg. No.
WASH DOOR & VENT COWL ASSEMBLY 8* 7 4 2 1 3 5 6 Top Vent Cowl Gasket: 5330-031-83-47 Side Vent Cowl Gasket: 5330-031-83-48 ITEM 1 2 3 4 5 6 7 8* QTY 1 1 2 2 1 2 1 1 DESCRIPTION Wash Door Handle Weldment Front Door Weldment Door Glide Vent Cowl Cover See Page Entitled “Hood Weldments” Vent Cowl Magnet, Door Switch, Modified Magnet, Door Switch, Hood Mounted NOTE: Stainless Steel Switch Box Weldment is no longer available. 37 Mfg. No.
MISCELLANEOUS DOOR ASSEMBLIES Door Guide (Left) Weldment 5700-002-32-51 Door Guide (Right) Weldment 5700-031-76-44 Door/Hood Support Weldment 5700-031-87-08 Door Splash Guard 5700-021-85-31 Door Catch Weldment 5700-031-84-80 Splash Shield Weldment 5700-031-85-16 38
MAGNET SWITCHES/RACK RAIL ACTUATOR SWITCH ASSEMBLIES Limit Switch Bracket 5700-021-71-18 Magnetic Reed Switch 5930-111-68-44 Small Limit Switch Actuator Assembly 5700-021-75-67 Limit Switch Actuator 5700-021-76-97 End Cap 5700-011-60-92 Magnet Bar 5700-111-69-25 Large Limit Switch Actuator Assembly (Left to Right Models) 5700-021-75-68 Limit Switch Actuator 5700-021-74-63 End Cap 5700-011-60-92 Magnet Bar 5700-111-69-25 Large Limit Switch Actuator Assembly (Right to Left Models) 5700-021-76-96 Limit
PAWL BAR ASSEMBLY/RACK RAIL WELDMENTS 2 1 4 3 5 This entire assembly may be ordered using part number 5700-031-81-02. ITEM 1 2 3 4 5 QTY 1 18 36 18 18 DESCRIPTION Pawl Bar Weldment Pawl Bar Dog Casting Pawl Bar Spacer Bolt, 3/8”-16 x 1-3/4” Long Locknuts, 3/8”-16 with Nylon Insert Mfg. No.
RINSE TRAY/PAWL BAR ROLLER BRACKET ASSEMBLY Order the Rinse Tray Strainer Weldment using part number 5700-041-85-09.
MISCELLANEOUS PARTS & WELDMENTS Rinse Drain Weldment 5700-021-68-28 Pawl Bar Roller Bracket Weldment without Studs 5700-031-92-36 Wash Fill Tube Weldment 5700-021-71-21 Rinse Drain Plug 5700-011-68-59 Pawl Bar Gutter Weldment 5700-021-66-86 42
MISCELLANEOUS PARTS & WELDMENTS (CONTINUED) Top Guide Block 5700-011-69-49 Bottom Guide Block 5700-011-69-50 Right Rinse Pan Locator Bracket 5700-021-92-37 Left Rinse Pan Locator Bracket 5700-021-92-38 Upper Wash Manifold Support Bracket 5700-021-73-97 Conduit Bracket 5700-021-70-88 Rinse Arm Support Bracket 5700-011-71-19 Pipe Clamp 5700-000-35-05 43
STRAINERS Intake Suction Scoop Strainer Weldment 5700-021-87-60 Drain Guard Strainer Weldment 5700-002-09-15 Screen Strainer with Handle Weldment 5700-002-09-04 44
FLOAT SWITCH ASSEMBLY Float Support Bracket 5700-021-85-15 Float Switch Cover 5700-021-75-71 Float Switch Nut (1/2”-13 Thread) 5310-011-72-58 Order the 1/2” Flat Washer using part number 5700-011-71-93.
CURTAINS Curtain, 21” Long x 20.5” Wide 8415-131-73-45 Middle Curtain Hook 5700-011-72-65 Secured with Locknut, 1/4”-20 with Nylon Insert 5310-374-01-00 Curtain, 12” Long x 20.
VENT SCOOP OPTION/EXHAUST FAN CONTROL OPTION Vent Cowl Baffle Weldment 5700-002-11-47 Vent Scoop Weldment 5700-002-12-18 Scoop Damper 5700-002-36-55 EXHAUST FAN CONTROL OPTION 2” Din Rail 5700-002-36-09 Terminal Board 5940-011-84-41 Delay Timer 5945-011-65-44 47
TABLE LIMIT SWITCH OPTION Limit Switch & Lever 5930-303-40-01 Switch Mounting Bracket 5700-000-14-55 Wall Mounting Bracket Limit Switch and Lever 12” Typ. Spacing 1.5” Typ. Spacing Limit Switch and Lever Dish Table Wall Side View Dish Table Top View Associated Hardware: Screw, 10-32 x 1-1/2” Long Fillister Head Locknut, 10-32 with Nylon Insert 5305-973-01-00 5310-373-02-00 For a complete replacement kit that comes with all of the hardware, conduit and wiring, use part number 5700-002-06-83.
DRAIN QUENCH SYSTEM (CONVEYOR SERIES) Schematic 2 1 9 3 To Dishmachine Drain To Cold Water Supply 10 8 4 5 7 8 4 7 To Drain 6 From the existing drain, attach the two additional Tees (Item 7) using the 1-1/2” NPT Close Nipples )Item 8). Tighten the Reducers (Items 6 & 9) into the Tees as shown above. Attach the Modified Compression Fitting (Item 10) into the 1-1/2” to 1/4” Reducer (Item 9).
AJ-64CE ELECTRICAL DIAGRAM 208V/230V - 60 HERTZ - SINGLE PHASE 50
AJ-64CE ELECTRICAL DIAGRAM 208V/230V - 60 HERTZ - THREE PHASE 51
AJ-64CE ELECTRICAL DIAGRAM 460V - 60 HERTZ - THREE PHASE 52
AJ-64CS ELECTRICAL DIAGRAM 208V/230V - 60 HERTZ - THREE PHASE 53
AJ-64CS ELECTRICAL DIAGRAM 208V/230V - 60 HERTZ - THREE PHASE 54
AJ-64CS ELECTRICAL DIAGRAM 460V - 60 HERTZ - THREE PHASE 55
