Installation Guide
Table Of Contents
- General Information
- Installation
- Component Identification
- Maintenance
- Operation
- Blade Tower Brixing
- CEV Electronic Ice & Carbonation Control
- Flavor Magic Programming
- Flav’R-Pic External Programming
- Flav’R-Pic (FRP-250) Programming
- Flav’R-Pic (FRP-250) Brixing Procedure
- FlexTower Programming Modes
- Control Board Run or Dispense Mode
- The 6 Programming Modes on FlexTower Control Board
- To Access Programming Modes
- To Exit Programming Modes
- Manual Dispense Mode
- Timed Dispense Mode (Flavor Adder Dispensed)
- Water Calibration Mode
- Syrup Calibration Mode
- Touchpad Configuration Mode
- Touchpad LED Light Sequencing Mode (8 Selection Area Touchpad)
- Touchpad LED Light Sequencing Mode (4 Selection Area Touchpad)
- Adjustments
- Agitation Timer
- Troubleshooting
- Component Specifications
- Charts
- Diagrams
- Blade Tower Plumbing
- CEV-30i & CEV-30e Plumbing
- CEV-40i & CEV-40e Plumbing
- CT-6 Plumbing and Wiring
- CT-8 Plumbing and Wiring
- CF-1522 Plumbing
- DI-1522 Post-mix Plumbing
- DI-1522 Pre-mix Plumbing
- DI/DIL-2323 6 Valve Post-mix Plumbing
- DI/DIL-2323 8 Valve Post-mix Plumbing & Variety Valve
- DI/DIL-2323 10 Valve Post-mix Plumbing
- DI/DIL-2323 6 Valve Pre-mix Plumbing
- Flavor Magic Plumbing
- FRP-250 Plumbing Diagram
- FRP-250 & FRP-250SCI Tubing Layout
- FT-8 Plumbing
- FT-12 Plumbing
- FlexTower Water Recirculation Pump Flow
- FlexTower Water Chiller Flow
- MDH-302 12 Valve Plumbing
- MDH-402 16 Valve Plumbing
- MDH-402 20 Valve Plumbing
- S/SV150 6 Valve Diagram
- S/SV175 8 Valve Diagram
- S/SV200/250/SV-250QD 8 Valve Diagram
- S/SV200/250 10 Valve Diagram
- Flex Manifold Diagrams
- CEV Wiring
- CF Drop-In Series Wiring
- Drop-in Wiring
- Flavor Magic Wiring
- Flav’R-Pic (FRP-250) Wiring
- FlexTower Wiring
- MDH-302 & MDH-402 Wiring
- NGF-250 Wiring
- quickdraw Wiring
- S/SV/SVi Wiring
- Selectable Ice Wiring
54 Part Number STH14 9/10
MDH-402 (CI & SCI) INTERNAL
CARBONATION DISPENSING SYSTEM
NOTE:
- Cold carbonator deck must be within 10 ft (3.05 m) of unit to
function properly.
- Cold carbonation deck must be placed on a level surface.
- Cold carbonation deck requires booster system if supply
water pressure is below 40 psi (2.8 bar), or if two units are
installed on the same water line.
- filtration system may be placed before booster pump (per
customer specifications).
- Items have been removed for clarity.
- 16 valve unit is shown.
Cut-in 70 psi (4.8 bar)
Cut-out 100 psi (6.9 bar)
Municipal
Water Supply
Filtration
System
For tank
pressures, refer
to manual for
specifications
Regulator
50-55 psi
(3.4-3.8 bar)
B-I-B Set to
60 psi
(4.1 bar)
Booster
System
Water from
Booster to
Pump Inlet
Carbonated Water
to Mainifold
(Insulated)
Cold Water to
Carbonator Tank
(Insulated)
Cold Carbonation Deck
CO
2
Supply
100 psi (6.9 bar) Min.
CO
2
Regulator
Fixed at
75 psi
(5.2 bar)
Non-carbonated
water to water
inlets on Unit
(Non-insulated)
from carbonator
pump
Cold Water to
Carbonator Tank
(Insulated)
Carbonated
Water to Manifold
(Insulated)
Plain Water to Manifold
(non-insulated)
Plain Water to Manifold
(non-insulated)
Non-carbonated
water to water
inlets on Unit
(Non-insulated)
from carbonator
pump
STH14.book Page 54 Thursday, September 23, 2010 3:35 PM