Installation Guide
Table Of Contents
- General Information
- Installation
- Component Identification
- Maintenance
- Operation
- Blade Tower Brixing
- CEV Electronic Ice & Carbonation Control
- Flavor Magic Programming
- Flav’R-Pic External Programming
- Flav’R-Pic (FRP-250) Programming
- Flav’R-Pic (FRP-250) Brixing Procedure
- FlexTower Programming Modes
- Control Board Run or Dispense Mode
- The 6 Programming Modes on FlexTower Control Board
- To Access Programming Modes
- To Exit Programming Modes
- Manual Dispense Mode
- Timed Dispense Mode (Flavor Adder Dispensed)
- Water Calibration Mode
- Syrup Calibration Mode
- Touchpad Configuration Mode
- Touchpad LED Light Sequencing Mode (8 Selection Area Touchpad)
- Touchpad LED Light Sequencing Mode (4 Selection Area Touchpad)
- Adjustments
- Agitation Timer
- Troubleshooting
- Component Specifications
- Charts
- Diagrams
- Blade Tower Plumbing
- CEV-30i & CEV-30e Plumbing
- CEV-40i & CEV-40e Plumbing
- CT-6 Plumbing and Wiring
- CT-8 Plumbing and Wiring
- CF-1522 Plumbing
- DI-1522 Post-mix Plumbing
- DI-1522 Pre-mix Plumbing
- DI/DIL-2323 6 Valve Post-mix Plumbing
- DI/DIL-2323 8 Valve Post-mix Plumbing & Variety Valve
- DI/DIL-2323 10 Valve Post-mix Plumbing
- DI/DIL-2323 6 Valve Pre-mix Plumbing
- Flavor Magic Plumbing
- FRP-250 Plumbing Diagram
- FRP-250 & FRP-250SCI Tubing Layout
- FT-8 Plumbing
- FT-12 Plumbing
- FlexTower Water Recirculation Pump Flow
- FlexTower Water Chiller Flow
- MDH-302 12 Valve Plumbing
- MDH-402 16 Valve Plumbing
- MDH-402 20 Valve Plumbing
- S/SV150 6 Valve Diagram
- S/SV175 8 Valve Diagram
- S/SV200/250/SV-250QD 8 Valve Diagram
- S/SV200/250 10 Valve Diagram
- Flex Manifold Diagrams
- CEV Wiring
- CF Drop-In Series Wiring
- Drop-in Wiring
- Flavor Magic Wiring
- Flav’R-Pic (FRP-250) Wiring
- FlexTower Wiring
- MDH-302 & MDH-402 Wiring
- NGF-250 Wiring
- quickdraw Wiring
- S/SV/SVi Wiring
- Selectable Ice Wiring
Part Number STH14 9/10 171
FRP-250 & FRP-250SCI Tubing Layout
S1= 6”
S2= 6”
S3= 6”
S4= 13”
C1= 10”
S13= 25”
S14= 6”
S15= 6”
S16= 6”
C4= 10”
S5= 13”
S6= 6”
S7= 6”
S8= 13”
C2= 1.5”
NC2= 10”
N3= 10”
S9= 25”
S10= 6”
S11= 6”
S12= 25”
C3= 1.5”
NC3= 10”
N4= 10”
F1= 13”
F2= 13”
F3= 13”
F4= 13”
F5= 18”
F6= 18”
F7= 18”
F8= 18”
S4
S1 S2
NC3C3
N4
NC2C2
N3
S3
C1
S9
S12 S10
S11
C1
F1
F1 F4
F3
CAP
F5
F6 F8
F7
CAP
020001779
NOZZLE 4
TOP VIEW
FRONT
NOZZLE 1
TOP VIEW
FRONT
NOZZLE 5
TOP VIEW
FRONT
NOZZLE 2
TOP VIEW
FRONT
NOZZLE 3
TOP VIEW
FRONT
NOZZLE 6
TOP VIEW
FRONT
020001779
S15
S13 S16
S14
C4
020001779
S7
S6 S5
S8
N3
020001779
020001779 020001779
STH14.book Page 171 Thursday, September 23, 2010 3:35 PM