Installation Guide
Table Of Contents
- General Information
- Installation
- Component Identification
- Maintenance
- Operation
- Blade Tower Brixing
- CEV Electronic Ice & Carbonation Control
- Flavor Magic Programming
- Flav’R-Pic External Programming
- Flav’R-Pic (FRP-250) Programming
- Flav’R-Pic (FRP-250) Brixing Procedure
- FlexTower Programming Modes
- Control Board Run or Dispense Mode
- The 6 Programming Modes on FlexTower Control Board
- To Access Programming Modes
- To Exit Programming Modes
- Manual Dispense Mode
- Timed Dispense Mode (Flavor Adder Dispensed)
- Water Calibration Mode
- Syrup Calibration Mode
- Touchpad Configuration Mode
- Touchpad LED Light Sequencing Mode (8 Selection Area Touchpad)
- Touchpad LED Light Sequencing Mode (4 Selection Area Touchpad)
- Adjustments
- Agitation Timer
- Troubleshooting
- Component Specifications
- Charts
- Diagrams
- Blade Tower Plumbing
- CEV-30i & CEV-30e Plumbing
- CEV-40i & CEV-40e Plumbing
- CT-6 Plumbing and Wiring
- CT-8 Plumbing and Wiring
- CF-1522 Plumbing
- DI-1522 Post-mix Plumbing
- DI-1522 Pre-mix Plumbing
- DI/DIL-2323 6 Valve Post-mix Plumbing
- DI/DIL-2323 8 Valve Post-mix Plumbing & Variety Valve
- DI/DIL-2323 10 Valve Post-mix Plumbing
- DI/DIL-2323 6 Valve Pre-mix Plumbing
- Flavor Magic Plumbing
- FRP-250 Plumbing Diagram
- FRP-250 & FRP-250SCI Tubing Layout
- FT-8 Plumbing
- FT-12 Plumbing
- FlexTower Water Recirculation Pump Flow
- FlexTower Water Chiller Flow
- MDH-302 12 Valve Plumbing
- MDH-402 16 Valve Plumbing
- MDH-402 20 Valve Plumbing
- S/SV150 6 Valve Diagram
- S/SV175 8 Valve Diagram
- S/SV200/250/SV-250QD 8 Valve Diagram
- S/SV200/250 10 Valve Diagram
- Flex Manifold Diagrams
- CEV Wiring
- CF Drop-In Series Wiring
- Drop-in Wiring
- Flavor Magic Wiring
- Flav’R-Pic (FRP-250) Wiring
- FlexTower Wiring
- MDH-302 & MDH-402 Wiring
- NGF-250 Wiring
- quickdraw Wiring
- S/SV/SVi Wiring
- Selectable Ice Wiring
164 Part Number STH14 9/10
DI-1522 Post-mix Plumbing
DI-1522 Pre-mix Plumbing
SERVEND RECOMMENDED PLUMBING: DI-1522 IC
Detail A
Detail A
S1
S2
S3
S4
S5
S6
Plain Water
Carb Water
FLEX
MANIFOLD
PW
From Pump
PW
Manifold: Change to Carbonated or
Non-carbonated water
1. Rotate plunger 180° using a 5/32" allen wrench.
2. Pull plunger up to get non-carbonated water.
3. Push plunger down to get carb. water.
4. Turn plunger back 180° to lock.
NOTE 1:
A. Plain water to the carbonator
B. Carb water to coldplate post-chill
NOTE 2:
For 5(4) vale unit:
– Inlet syrup number 6(6.5) isn’t used
– Valve number 6(6.5) isn’t used
Ambient Carbonation
Jumper tube between pre-chill
coldplate and post-chill in coldplate
For Assistance Call
812-246-7000
2-1-1-2 Right to Left
SERVEND RECOMMENDED PLUMBING: DI-1522 PREMIX
Line 6
Line 5
Line 4
Line 3
Line 2
Line 1
Valve Locations
For Assistance Call
812-246-7000
3/4" NPT
Drainpan
Drain
3/4" NPT
Coldplate
Drain
Bottom View
For 5 valve unit:
Line 6 is not used
For 4 valve unit:
Lines 1 & 6 are not used
Inlet Line Locations
Line 3
Line 2
Line 1
Line 6
Line 5
Line 4
STH14.book Page 164 Thursday, September 23, 2010 3:35 PM