Installation Guide
Table Of Contents
- General Information
- Installation
- Component Identification
- Maintenance
- Operation
- Blade Tower Brixing
- CEV Electronic Ice & Carbonation Control
- Flavor Magic Programming
- Flav’R-Pic External Programming
- Flav’R-Pic (FRP-250) Programming
- Flav’R-Pic (FRP-250) Brixing Procedure
- FlexTower Programming Modes
- Control Board Run or Dispense Mode
- The 6 Programming Modes on FlexTower Control Board
- To Access Programming Modes
- To Exit Programming Modes
- Manual Dispense Mode
- Timed Dispense Mode (Flavor Adder Dispensed)
- Water Calibration Mode
- Syrup Calibration Mode
- Touchpad Configuration Mode
- Touchpad LED Light Sequencing Mode (8 Selection Area Touchpad)
- Touchpad LED Light Sequencing Mode (4 Selection Area Touchpad)
- Adjustments
- Agitation Timer
- Troubleshooting
- Component Specifications
- Charts
- Diagrams
- Blade Tower Plumbing
- CEV-30i & CEV-30e Plumbing
- CEV-40i & CEV-40e Plumbing
- CT-6 Plumbing and Wiring
- CT-8 Plumbing and Wiring
- CF-1522 Plumbing
- DI-1522 Post-mix Plumbing
- DI-1522 Pre-mix Plumbing
- DI/DIL-2323 6 Valve Post-mix Plumbing
- DI/DIL-2323 8 Valve Post-mix Plumbing & Variety Valve
- DI/DIL-2323 10 Valve Post-mix Plumbing
- DI/DIL-2323 6 Valve Pre-mix Plumbing
- Flavor Magic Plumbing
- FRP-250 Plumbing Diagram
- FRP-250 & FRP-250SCI Tubing Layout
- FT-8 Plumbing
- FT-12 Plumbing
- FlexTower Water Recirculation Pump Flow
- FlexTower Water Chiller Flow
- MDH-302 12 Valve Plumbing
- MDH-402 16 Valve Plumbing
- MDH-402 20 Valve Plumbing
- S/SV150 6 Valve Diagram
- S/SV175 8 Valve Diagram
- S/SV200/250/SV-250QD 8 Valve Diagram
- S/SV200/250 10 Valve Diagram
- Flex Manifold Diagrams
- CEV Wiring
- CF Drop-In Series Wiring
- Drop-in Wiring
- Flavor Magic Wiring
- Flav’R-Pic (FRP-250) Wiring
- FlexTower Wiring
- MDH-302 & MDH-402 Wiring
- NGF-250 Wiring
- quickdraw Wiring
- S/SV/SVi Wiring
- Selectable Ice Wiring
110 Part Number STH14 9/10
4. The correct volume should be 5 oz. (147.86 cc)
during the fixed dispense in Mode 2. If adjustment
is needed to attain this volume, make adjustments
to the left side of valve 8 (C1) adjustment screw
as needed until flow rate is satisfactory.
NOTE: The touch pad mount can be tilted forward in
order to give you better access to the valves.
5. For syrup brixing place the brix cup with the syrup
side of the cup under the nozzle area and press
any brand touch pad area associated with that
nozzle dispense point. For example S1 (Syrup 1),
S2, S3, and S4 touch pad areas will be used to
brix N1 (Nozzle 1).
6. Syrup will dispense for a fixed duration and
should be even with the 5 oz. (147.86 cc) water
mark on the cup, or 1 oz (29.57cc) just below the
30cc mark on the syrup side of the brix cup.
7. Check each syrup position and adjust syrup on
the corresponding valve as necessary. A
plumbing label is located on the foam front of the
unit showing the position of each valve and syrup
port. See the plumbing diagram.
8. When finished, move on to another nozzle or, if
your brixing is complete, return the control board
to the dispense mode by pressing the program
button and holding for 3 seconds or until the LED
displays 0. Replace the splash panel and
merchandiser.
STH14.book Page 110 Thursday, September 23, 2010 3:35 PM