Installation Guide
Table Of Contents
- General Information
- Installation
- Component Identification
- Maintenance
- Operation
- Blade Tower Brixing
- CEV Electronic Ice & Carbonation Control
- Flavor Magic Programming
- Flav’R-Pic External Programming
- Flav’R-Pic (FRP-250) Programming
- Flav’R-Pic (FRP-250) Brixing Procedure
- FlexTower Programming Modes
- Control Board Run or Dispense Mode
- The 6 Programming Modes on FlexTower Control Board
- To Access Programming Modes
- To Exit Programming Modes
- Manual Dispense Mode
- Timed Dispense Mode (Flavor Adder Dispensed)
- Water Calibration Mode
- Syrup Calibration Mode
- Touchpad Configuration Mode
- Touchpad LED Light Sequencing Mode (8 Selection Area Touchpad)
- Touchpad LED Light Sequencing Mode (4 Selection Area Touchpad)
- Adjustments
- Agitation Timer
- Troubleshooting
- Component Specifications
- Charts
- Diagrams
- Blade Tower Plumbing
- CEV-30i & CEV-30e Plumbing
- CEV-40i & CEV-40e Plumbing
- CT-6 Plumbing and Wiring
- CT-8 Plumbing and Wiring
- CF-1522 Plumbing
- DI-1522 Post-mix Plumbing
- DI-1522 Pre-mix Plumbing
- DI/DIL-2323 6 Valve Post-mix Plumbing
- DI/DIL-2323 8 Valve Post-mix Plumbing & Variety Valve
- DI/DIL-2323 10 Valve Post-mix Plumbing
- DI/DIL-2323 6 Valve Pre-mix Plumbing
- Flavor Magic Plumbing
- FRP-250 Plumbing Diagram
- FRP-250 & FRP-250SCI Tubing Layout
- FT-8 Plumbing
- FT-12 Plumbing
- FlexTower Water Recirculation Pump Flow
- FlexTower Water Chiller Flow
- MDH-302 12 Valve Plumbing
- MDH-402 16 Valve Plumbing
- MDH-402 20 Valve Plumbing
- S/SV150 6 Valve Diagram
- S/SV175 8 Valve Diagram
- S/SV200/250/SV-250QD 8 Valve Diagram
- S/SV200/250 10 Valve Diagram
- Flex Manifold Diagrams
- CEV Wiring
- CF Drop-In Series Wiring
- Drop-in Wiring
- Flavor Magic Wiring
- Flav’R-Pic (FRP-250) Wiring
- FlexTower Wiring
- MDH-302 & MDH-402 Wiring
- NGF-250 Wiring
- quickdraw Wiring
- S/SV/SVi Wiring
- Selectable Ice Wiring
Part Number STH14 9/10 101
N3 & N4 Carbonated or Non-Carbonated Drinks
FRP-250 with Flavor Shots
FRP-250 with out Flavor Shots
1. Choose a control board. If programing N3 (Nozzle 3)
use the left control board, if programming N4 use the
right control board. Beverage dispense points are
designated by a black nozzle.
2. Press the program button and hold for 3 seconds or
until the LED displays 1.
3. To set a carbonated drink for N3 (Nozzle 3) touch one
of the following touch pads; S5, S6, S7, or S8 until the
LEDs around the touch pad are constant.
4. To set a non-carbonated drink for N3 (Nozzle 3) touch
one of the following touch pads; S5, S6, S7, or S8 until
the LEDs around the touch pad are blinking.
- Constant LEDs = Carbonated
- Blinking LEDs = Non-Carbonated
5. Follow the same instructions for N4 (Nozzle 4) using
the right control board and touch pads S9, S10, S11, or
S12.
6. When you are finished, press the program button to go
to a different mode or save your settings and return the
control board to the dispense mode by pressing the
program button and holding for 3 seconds or until the
LED displays 0.
S1
S3
S2
S4
S5
S7
S6
S8
F1
F2
F4
F3
N1
N3
N2
S12
S10
S11 S9
S16 S14
S15 S13
F5
F6 F8
F7
N4 N6
N5
Right Flavor
Shots
Left Flavor
Shots
Left Carb/
Non-Carb
Right
Carb/Non-
Carb
S1
S3
S2
S4
S5
S7
S6
S8
F1
F2
F4
F3
N1
N3
S12
S10
S11
S9
S16 S14
S15
S13
F5
F6
F8
F7
N4
N6
Right
Hidden
Touchpad
Button
Left
Hidden
Touchpad
Button
Left Carb/
Non-Carb
Right
Carb/Non-
Carb
STH14.book Page 101 Thursday, September 23, 2010 3:35 PM