Installation Guide
Table Of Contents
- General Information
- Installation
- Component Identification
- Maintenance
- Operation
- Blade Tower Brixing
- CEV Electronic Ice & Carbonation Control
- Flavor Magic Programming
- Flav’R-Pic External Programming
- Flav’R-Pic (FRP-250) Programming
- Flav’R-Pic (FRP-250) Brixing Procedure
- FlexTower Programming Modes
- Control Board Run or Dispense Mode
- The 6 Programming Modes on FlexTower Control Board
- To Access Programming Modes
- To Exit Programming Modes
- Manual Dispense Mode
- Timed Dispense Mode (Flavor Adder Dispensed)
- Water Calibration Mode
- Syrup Calibration Mode
- Touchpad Configuration Mode
- Touchpad LED Light Sequencing Mode (8 Selection Area Touchpad)
- Touchpad LED Light Sequencing Mode (4 Selection Area Touchpad)
- Adjustments
- Agitation Timer
- Troubleshooting
- Component Specifications
- Charts
- Diagrams
- Blade Tower Plumbing
- CEV-30i & CEV-30e Plumbing
- CEV-40i & CEV-40e Plumbing
- CT-6 Plumbing and Wiring
- CT-8 Plumbing and Wiring
- CF-1522 Plumbing
- DI-1522 Post-mix Plumbing
- DI-1522 Pre-mix Plumbing
- DI/DIL-2323 6 Valve Post-mix Plumbing
- DI/DIL-2323 8 Valve Post-mix Plumbing & Variety Valve
- DI/DIL-2323 10 Valve Post-mix Plumbing
- DI/DIL-2323 6 Valve Pre-mix Plumbing
- Flavor Magic Plumbing
- FRP-250 Plumbing Diagram
- FRP-250 & FRP-250SCI Tubing Layout
- FT-8 Plumbing
- FT-12 Plumbing
- FlexTower Water Recirculation Pump Flow
- FlexTower Water Chiller Flow
- MDH-302 12 Valve Plumbing
- MDH-402 16 Valve Plumbing
- MDH-402 20 Valve Plumbing
- S/SV150 6 Valve Diagram
- S/SV175 8 Valve Diagram
- S/SV200/250/SV-250QD 8 Valve Diagram
- S/SV200/250 10 Valve Diagram
- Flex Manifold Diagrams
- CEV Wiring
- CF Drop-In Series Wiring
- Drop-in Wiring
- Flavor Magic Wiring
- Flav’R-Pic (FRP-250) Wiring
- FlexTower Wiring
- MDH-302 & MDH-402 Wiring
- NGF-250 Wiring
- quickdraw Wiring
- S/SV/SVi Wiring
- Selectable Ice Wiring
150 Part Number STH14 9/10
Flav’R-Pic (FRP-250) Logic Matrix
System power on
(24V from transformer)
Energize
Touchpad (active)
Touchpad LEDs (sync w/other touchpad)
Program Mode?
Prog button
pressed > 3s?
LCD display
= 1
Brand or Flavor?
Carb/Non-carb Mode (Brand only)
Cont. LED - carbonated
Flash LED (0.5s on/off) - plain
Tap touchpad to switch
Dispense Time Mode (Flavor only)
Cont. LED - 1s dispense
Flash LED (0.5s on/off) - 1s dispense
Tap touchpad to switch
Prog button
pressed > 3s or
300s elapsed?
LCD Display
= 2
Brix Mode
Fixed 1.6s dispense
Brand = syrup and
Flavor=
F1 = C1, F2 = C2,
F3 = NC2
F5 = C4, F6 = C3,
F7 - NC3
Tap touchpad to activate
Prog button
pressed > 3s or
300s elapsed?
LCD Display
= 3
LED Sequence Mode
Touch brand button location shown below to change
1. LED flash outside to center (0.5s on/off) Default (S1 andS16)
2. LED flash center to outside (0.5s on/off) (S2 and S15)
3. LED flash all (0.5s on/off) (S3 and S14)
4. LED continuous (S4 and S13)
5. LED chaser left to right (S4 and S11)
6. LED chaser right to left (S6 and S12)
7. LED off all (S7 and S10)
Prog button
pressed > 3s or
300s elapsed?
LCD Display
= 0
Normal Dispense Mode
Brand - ON MODE - Water on then Syrup on 60 ms later.
OFF MODE - Syrup off then Water off 60 ms later.
Flavor shot - 1s or 2 s (release and press - no delay between dispenses)
n
n
y
n
y
n
y
Brand
Flavor
y
STH14.book Page 150 Thursday, September 23, 2010 3:35 PM