Installation Guide
Table Of Contents
- General Information
- Installation
- Component Identification
- Maintenance
- Operation
- Blade Tower Brixing
- CEV Electronic Ice & Carbonation Control
- Flavor Magic Programming
- Flav’R-Pic External Programming
- Flav’R-Pic (FRP-250) Programming
- Flav’R-Pic (FRP-250) Brixing Procedure
- FlexTower Programming Modes
- Control Board Run or Dispense Mode
- The 6 Programming Modes on FlexTower Control Board
- To Access Programming Modes
- To Exit Programming Modes
- Manual Dispense Mode
- Timed Dispense Mode (Flavor Adder Dispensed)
- Water Calibration Mode
- Syrup Calibration Mode
- Touchpad Configuration Mode
- Touchpad LED Light Sequencing Mode (8 Selection Area Touchpad)
- Touchpad LED Light Sequencing Mode (4 Selection Area Touchpad)
- Adjustments
- Agitation Timer
- Troubleshooting
- Component Specifications
- Charts
- Diagrams
- Blade Tower Plumbing
- CEV-30i & CEV-30e Plumbing
- CEV-40i & CEV-40e Plumbing
- CT-6 Plumbing and Wiring
- CT-8 Plumbing and Wiring
- CF-1522 Plumbing
- DI-1522 Post-mix Plumbing
- DI-1522 Pre-mix Plumbing
- DI/DIL-2323 6 Valve Post-mix Plumbing
- DI/DIL-2323 8 Valve Post-mix Plumbing & Variety Valve
- DI/DIL-2323 10 Valve Post-mix Plumbing
- DI/DIL-2323 6 Valve Pre-mix Plumbing
- Flavor Magic Plumbing
- FRP-250 Plumbing Diagram
- FRP-250 & FRP-250SCI Tubing Layout
- FT-8 Plumbing
- FT-12 Plumbing
- FlexTower Water Recirculation Pump Flow
- FlexTower Water Chiller Flow
- MDH-302 12 Valve Plumbing
- MDH-402 16 Valve Plumbing
- MDH-402 20 Valve Plumbing
- S/SV150 6 Valve Diagram
- S/SV175 8 Valve Diagram
- S/SV200/250/SV-250QD 8 Valve Diagram
- S/SV200/250 10 Valve Diagram
- Flex Manifold Diagrams
- CEV Wiring
- CF Drop-In Series Wiring
- Drop-in Wiring
- Flavor Magic Wiring
- Flav’R-Pic (FRP-250) Wiring
- FlexTower Wiring
- MDH-302 & MDH-402 Wiring
- NGF-250 Wiring
- quickdraw Wiring
- S/SV/SVi Wiring
- Selectable Ice Wiring
126 Part Number STH14 9/10
Ice dispenses
continuously
Misaligned
microswitch
Adjust microswitch.
Agitation timer set
incorrectly
Test agitation timer.
Thumping noise or
irregular sound at
a particular area of
the dispenser
Shaved ice clusters
in the bin
Remove clusters, discover why
ice is shaving, and then repair.
Dispensing
crushed ice or
reduced
dispensing speed
Water spillage from
ice machine into
dispenser bin
Adjust ice machine.
Agitation timer
(FRP-250)
Test agitation timer.
Bridge of ice sheet is
too thick
Adjust ice machine.
Paddle wheel area
broken or cracked
Replace paddle wheel area.
Ice clusters in bin Break up or remove clusters.
Door not fully open Adjust door.
Door will not close Ice jammed in chute Adjust bridge in ice machine or,
when manually filling, break up
clusters.
Door and/or door
lock has come out of
place
Replace door and lock into
proper position.
Mounting brackets
for rocking chute
have spread too
far apart
Stretched during
removal for cleaning
or maintenance
Bend parts into shape.
Problem Possible Cause To Correct
STH14.book Page 126 Thursday, September 23, 2010 3:35 PM