Installation Guide
Table Of Contents
- General Information
- Installation
- Component Identification
- Maintenance
- Operation
- Blade Tower Brixing
- CEV Electronic Ice & Carbonation Control
- Flavor Magic Programming
- Flav’R-Pic External Programming
- Flav’R-Pic (FRP-250) Programming
- Flav’R-Pic (FRP-250) Brixing Procedure
- FlexTower Programming Modes
- Control Board Run or Dispense Mode
- The 6 Programming Modes on FlexTower Control Board
- To Access Programming Modes
- To Exit Programming Modes
- Manual Dispense Mode
- Timed Dispense Mode (Flavor Adder Dispensed)
- Water Calibration Mode
- Syrup Calibration Mode
- Touchpad Configuration Mode
- Touchpad LED Light Sequencing Mode (8 Selection Area Touchpad)
- Touchpad LED Light Sequencing Mode (4 Selection Area Touchpad)
- Adjustments
- Agitation Timer
- Troubleshooting
- Component Specifications
- Charts
- Diagrams
- Blade Tower Plumbing
- CEV-30i & CEV-30e Plumbing
- CEV-40i & CEV-40e Plumbing
- CT-6 Plumbing and Wiring
- CT-8 Plumbing and Wiring
- CF-1522 Plumbing
- DI-1522 Post-mix Plumbing
- DI-1522 Pre-mix Plumbing
- DI/DIL-2323 6 Valve Post-mix Plumbing
- DI/DIL-2323 8 Valve Post-mix Plumbing & Variety Valve
- DI/DIL-2323 10 Valve Post-mix Plumbing
- DI/DIL-2323 6 Valve Pre-mix Plumbing
- Flavor Magic Plumbing
- FRP-250 Plumbing Diagram
- FRP-250 & FRP-250SCI Tubing Layout
- FT-8 Plumbing
- FT-12 Plumbing
- FlexTower Water Recirculation Pump Flow
- FlexTower Water Chiller Flow
- MDH-302 12 Valve Plumbing
- MDH-402 16 Valve Plumbing
- MDH-402 20 Valve Plumbing
- S/SV150 6 Valve Diagram
- S/SV175 8 Valve Diagram
- S/SV200/250/SV-250QD 8 Valve Diagram
- S/SV200/250 10 Valve Diagram
- Flex Manifold Diagrams
- CEV Wiring
- CF Drop-In Series Wiring
- Drop-in Wiring
- Flavor Magic Wiring
- Flav’R-Pic (FRP-250) Wiring
- FlexTower Wiring
- MDH-302 & MDH-402 Wiring
- NGF-250 Wiring
- quickdraw Wiring
- S/SV/SVi Wiring
- Selectable Ice Wiring
118 Part Number STH14 9/10
Touchpad Configuration Mode
Once in program mode (5), the control board LED
displays (5). Press the first and last touchpad selection
areas on both touchpads. The touchpad LED lights
sequence through all the touchpad selection areas
indicating the touchpad has been configured. After
configuring both touchpads, either enter another
program mode or exit the programming modes, which
will save programming mode changes.
Touchpad LED Light Sequencing Mode
(8 Selection Area Touchpad)
Once in program mode (6), the control board LED
displays (6). Press the first touchpad selection areas
on either touchpad for clockwise LED light
sequencing. The touchpad LED lights sequence
clockwise through all the touchpad selection areas
indicating the touchpad has been configured for
clockwise LED light sequencing. Or press the second
touchpad selection areas on either touchpad for
counterclockwise LED light sequencing. The touchpad
LED lights sequence counterclockwise through all the
touchpad selection areas indicating the touchpad has
been configured for counterclockwise LED light
sequencing. Or press the third touchpad selection
area on either touchpad to turn off LED light
sequencing. The third touchpad area LED lights
illuminate for 3 seconds then turn off indicating the
8 Selection Area 4 Selection Area
STH14.book Page 118 Thursday, September 23, 2010 3:35 PM