Installation Guide
Table Of Contents
- General Information
- Installation
- Component Identification
- Maintenance
- Operation
- Blade Tower Brixing
- CEV Electronic Ice & Carbonation Control
- Flavor Magic Programming
- Flav’R-Pic External Programming
- Flav’R-Pic (FRP-250) Programming
- Flav’R-Pic (FRP-250) Brixing Procedure
- FlexTower Programming Modes
- Control Board Run or Dispense Mode
- The 6 Programming Modes on FlexTower Control Board
- To Access Programming Modes
- To Exit Programming Modes
- Manual Dispense Mode
- Timed Dispense Mode (Flavor Adder Dispensed)
- Water Calibration Mode
- Syrup Calibration Mode
- Touchpad Configuration Mode
- Touchpad LED Light Sequencing Mode (8 Selection Area Touchpad)
- Touchpad LED Light Sequencing Mode (4 Selection Area Touchpad)
- Adjustments
- Agitation Timer
- Troubleshooting
- Component Specifications
- Charts
- Diagrams
- Blade Tower Plumbing
- CEV-30i & CEV-30e Plumbing
- CEV-40i & CEV-40e Plumbing
- CT-6 Plumbing and Wiring
- CT-8 Plumbing and Wiring
- CF-1522 Plumbing
- DI-1522 Post-mix Plumbing
- DI-1522 Pre-mix Plumbing
- DI/DIL-2323 6 Valve Post-mix Plumbing
- DI/DIL-2323 8 Valve Post-mix Plumbing & Variety Valve
- DI/DIL-2323 10 Valve Post-mix Plumbing
- DI/DIL-2323 6 Valve Pre-mix Plumbing
- Flavor Magic Plumbing
- FRP-250 Plumbing Diagram
- FRP-250 & FRP-250SCI Tubing Layout
- FT-8 Plumbing
- FT-12 Plumbing
- FlexTower Water Recirculation Pump Flow
- FlexTower Water Chiller Flow
- MDH-302 12 Valve Plumbing
- MDH-402 16 Valve Plumbing
- MDH-402 20 Valve Plumbing
- S/SV150 6 Valve Diagram
- S/SV175 8 Valve Diagram
- S/SV200/250/SV-250QD 8 Valve Diagram
- S/SV200/250 10 Valve Diagram
- Flex Manifold Diagrams
- CEV Wiring
- CF Drop-In Series Wiring
- Drop-in Wiring
- Flavor Magic Wiring
- Flav’R-Pic (FRP-250) Wiring
- FlexTower Wiring
- MDH-302 & MDH-402 Wiring
- NGF-250 Wiring
- quickdraw Wiring
- S/SV/SVi Wiring
- Selectable Ice Wiring
104 Part Number STH14 9/10
PROGRAM MODE 3
Light Sequences
Mode 3 displayed above, allows you to set the light
sequence for the touch pad LEDs. Follow the steps
below to place the board into this mode and set
sequences.
1. Choose a control board. If setting the light
sequence for the touch pad area on the left use
the left control board, or if you are setting them for
the right, use the right control board.
2. Press the program button and hold for 3 seconds
or until the LED displays 1. Press the program
button again until 3 is displayed on the control
board LED display.
3. With the left control board in mode 3 you can now
choose one of the seven touch pad LED lighting
sequences by pressing one of the following touch
pad areas:
S1 = Flash outside to center
S2 = Flash center to outside
S3 = Flash all
S4 = Continuously on all
S5 = Chaser left to right
S6 = Chaser right to left
S7 = Off all
S8 = Flash outside to center, Flavor Shot Off
NOTE: It is recommended that both boards be set to
the same lighting sequence. If not, the boards will not
be able to sync and lighting behavior may become
erratic.
4. With the right control board in mode 3 you can
now choose one of the seven touch pad LED
lighting sequences by pressing one of the
following touch pad areas:
S16 = Flash outside to center
S15 = Flash center to outside
S14 = Flash all
S13 = Continuously on all
STH14.book Page 104 Thursday, September 23, 2010 3:35 PM