Installation Guide
Table Of Contents
- General Information
- Installation
- Component Identification
- Maintenance
- Operation
- Blade Tower Brixing
- CEV Electronic Ice & Carbonation Control
- Flavor Magic Programming
- Flav’R-Pic External Programming
- Flav’R-Pic (FRP-250) Programming
- Flav’R-Pic (FRP-250) Brixing Procedure
- FlexTower Programming Modes
- Control Board Run or Dispense Mode
- The 6 Programming Modes on FlexTower Control Board
- To Access Programming Modes
- To Exit Programming Modes
- Manual Dispense Mode
- Timed Dispense Mode (Flavor Adder Dispensed)
- Water Calibration Mode
- Syrup Calibration Mode
- Touchpad Configuration Mode
- Touchpad LED Light Sequencing Mode (8 Selection Area Touchpad)
- Touchpad LED Light Sequencing Mode (4 Selection Area Touchpad)
- Adjustments
- Agitation Timer
- Troubleshooting
- Component Specifications
- Charts
- Diagrams
- Blade Tower Plumbing
- CEV-30i & CEV-30e Plumbing
- CEV-40i & CEV-40e Plumbing
- CT-6 Plumbing and Wiring
- CT-8 Plumbing and Wiring
- CF-1522 Plumbing
- DI-1522 Post-mix Plumbing
- DI-1522 Pre-mix Plumbing
- DI/DIL-2323 6 Valve Post-mix Plumbing
- DI/DIL-2323 8 Valve Post-mix Plumbing & Variety Valve
- DI/DIL-2323 10 Valve Post-mix Plumbing
- DI/DIL-2323 6 Valve Pre-mix Plumbing
- Flavor Magic Plumbing
- FRP-250 Plumbing Diagram
- FRP-250 & FRP-250SCI Tubing Layout
- FT-8 Plumbing
- FT-12 Plumbing
- FlexTower Water Recirculation Pump Flow
- FlexTower Water Chiller Flow
- MDH-302 12 Valve Plumbing
- MDH-402 16 Valve Plumbing
- MDH-402 20 Valve Plumbing
- S/SV150 6 Valve Diagram
- S/SV175 8 Valve Diagram
- S/SV200/250/SV-250QD 8 Valve Diagram
- S/SV200/250 10 Valve Diagram
- Flex Manifold Diagrams
- CEV Wiring
- CF Drop-In Series Wiring
- Drop-in Wiring
- Flavor Magic Wiring
- Flav’R-Pic (FRP-250) Wiring
- FlexTower Wiring
- MDH-302 & MDH-402 Wiring
- NGF-250 Wiring
- quickdraw Wiring
- S/SV/SVi Wiring
- Selectable Ice Wiring
96 Part Number STH14 9/10
8. A flavor tab for the 4th flavor will have to be added
to the touch pad. To do this, obtain one (1) P/N
5030780 20 flavor decal pad. Remove the P/N
5031579 decal overlay and add the 4th flavor tab
as well as replace any flavor tabs which came off
when removing the decal overlay. Note position of
4th flavor on the touch pad in the picture and
placed tab where indicated. Obtain a new P/N
5031579 decal overlay and place over the tabs.
If the customer decides to go back to 3 flavors, it will
not be necessary to change the board back to 3
flavors. However, it can be done by following steps 1
through 6 above. The number “3” will appear on the
display. Then disconnect the number “4” syrup from
the system, remove the 5031579 decal overlay,
remove the flavor tab “4” and replace the 5031579
decal overlay. It would be a good idea to have an
additional P/N 5030780 in case flavor tabs are
damaged in the process.
STEADY OR FLASHING TOUCH PAD LED
The blue LED on the touch pad can be set to one of
two display modes:
1. Steady illumination. This is the default mode and
the LED will remain on steady until dispense is
activated. The light will flash only when product is
being dispensed. In this mode, the control board
display will read “Off”.
2. Flash mode. The LED will turn on for 1/2 second
and off for 1/2 second.
Enter the Flash mode by pressing the program button
until a flashing “- - - -” is displayed. Pressing flavor
button 1 (far left button) will switch from “Off” (default)
to “On”. The LED will now flash. To change back to the
default simply press flavor button 1 again and the
display should read “Off”. Press program button to exit
to the next program function.
STH14.book Page 96 Thursday, September 23, 2010 3:35 PM