WIRELESS ROUTER USER MANUAL MODELS 525459, 525466, 525480 1200AC Model 505480 150N Model 505459 300N Model 505466 MH-525459/525466/525480-UM-0713-01
Thank you for purchasing this Manhattan Wireless Router: Model 525459 (150N 4-Port), Model 525466 (300N 4-Port) or Model 525480 (1200AC 4-Port). ® The latest in wireless networking, these Wireless Routers serve multiple purposes — an access point for your wireless network, a four-port router for hard-wiring Ethernet devices — and bring it all together so that the devices can access a high-speed Internet connection.
TABLE OF CONTENTS section page 1 HARDWARE............................................5 1.1 Front Panel Display...........................5 1.2 Back Panel Display...........................5 2 SYSTEM & NETWORK SETUP..............6 2.1 Connecting the Router......................6 2.2 Obtaining an IP Address...................6 2.2.1 Windows XP Setup.....................7 2.2.2 Windows Vista/7 Setup...............9 2.2.3 Router IP Address Lookup........ 10 2.3 Quick Setup..........
SAFETY GUIDELINES For the protection of equipment users and connected devices, follow these safety guidelines: 1. This router is designed for indoor use only; do not place this router outdoors. 2. Do not place this router in hot or humid environments. 3. Do not yank any connected cables. 4. Firmly secure this device if it’s placed at any significant height. 5. Router accessories such as the antenna and power supply should be considered dangerous when handled by children under the age of 3.
1 HARDWARE 1.1 Front Panel Display 150N / 300N 1200AC LED PWR WLAN Status On On Flashing WAN / On WAN LNK/ACT Flashing LAN (1-4) On LAN LNK/ACT Flashing 2.4G On Flashing 5G On Flashing Description Router is powered on. Wireless network is switched on or WPS mode is on. Wireless LAN activity (transferring or receiving data). WAN port is connected. WAN activity (transferring or receiving data). LAN port is connected. LAN activity (transferring or receiving data). 2.4GHz Wireless WPS function is enabled.
2 SYSTEM & NETWORK SETUP 2.1 Connecting the Router 1. Connect your DSL or cable modem to the WAN port of the router using the provided RJ45 Ethernet cable. NOTE: Standard modems provided by Internet service providers come with at least one LAN/Ethernet port, which connects to the WAN port of the router. Example: 150N 2 1 3 2.
NOTE: If this procedure is successful, skip the following subsections and proceed to 2.3 Using Quick Setup. If the above procedure doesn’t result in your obtaining an IP address, or if you know that your computer has a static IP address setup, follow the steps in the appropriate subsection below. 2.2.1 Windows XP IP Address Setup 1. Click “Start,” then go to the control panel.
2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically,” then click “OK.
2.2.2 Windows Vista/7 IP Address Setup 1. Click “Start,” then go to the control panel. Click “View Network Status and Tasks,” then click “Manage Network Connections.” Right-click “Local Area Network,” then select “Properties.” With the Local Area Connection Properties window displayed, select “Internet Protocol Version 4 (TCP / IPv4),” and click “Properties.
2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically,” then click “OK.” 2.2.3 Router IP Address Lookup 1. After the IP address is set up, click “Start” at the bottom-left of the desktop, then click “Run.
2. With the Run window displayed, enter “cmd” in the “Open:” text field, then click “OK.
3. Enter “ipconfig,” then press . The IP address displays, followed by the default gateway. In the example below, the IP address of the router is 192.168.2.1. NOTE: If the IP address of the gateway is not displayed, or if the address begins with 169, recheck the network connection between your computer and the router, and re-check each step of the network setup procedure. 4.
2.3 Quick Setup The Quick Setup procedure lets you configure all the settings required for quick Internet access. . The initial Quick Setup screen presents time settings. Set Time Zone — Use the drop-down menu to select your time zone. Time Server Address — Enter the IP address/hostname of the time server. This isn’t normally required, but if the default time server (NTP) should go offline, you can obtain a new NTP server from the list at http://www.ntp.org.
Click “Next” to continue to the next screen of the Quick Setup procedure, where you select the broadband (Internet connection) type you use. On all screens, click “Apply” (if such button appears at the bottom) to submit any option or configuration changes. Click “Back” to return to the previous screen. Click “Cancel” to undo any changes you’ve made on that screen. Click “Next” or “OK” to proceed to the next screen.
MAC address — Enter the MAC address of your computer here if your service provider only permits a computer with a certain MAC address to access the Internet. If you’re using a computer used to connect to the Internet via cable modem, you can simply click “Clone Mac address” to fill in the MAC address field with the MAC address of your computer. 2.3.2 Setup Procedure for Fixed IP xDSL (Static IP) IP address — Enter the IP address assigned by your ISP.
2.3.3 Setup Procedure for PPPoE xDSL User Name — Enter the username assigned by your ISP. Password — Enter the password assigned by your ISP. Service Name — Provide a name for this Internet service. (optional) MTU — Enter the MTU value of your network connection. NOTE: Use the default value unless your ISP specifies otherwise. Connection Type — Select one of the three connection types in the drop-down menu: • “Continuous” keeps the Internet connection alive and does not disconnect. .
correctly entered; otherwise, the Internet connection will fail even if the PPTP settings are correct. Contact your ISP if you don’t know how you should fill in these fields. The PPTP Settings panel presents these options: User Name — Enter the username assigned by your ISP. Password — Enter the password provided by your ISP. PPTP Gateway — Enter the IP address of PPTP gateway assigned by your ISP. Connection ID — Enter the connection ID. (optional) MTU — Enter the MTU value of your network connection.
2.3.5 Setup Procedure for L2TP xDSL L2TP is another popular connection method for xDSL and other Internet connection types, and all required setting items are the same as the PPTP connection (see section 2.3.4 above). 2.3.6 Setup Procedure for Telstra BigPond This procedure is only for the Telstra BigPond network service in Australia. User Name — Enter the username assigned by Telstra. Password — Enter the password assigned by Telstra.
NOTE TO DSL USERS While PPPoE is the most common way to connect to DSL Internet service, it still may be necessary to enable “Cable Modem” in the Broadband settings. Below are examples for using Cable Modem instead of xDSL PPPoE, even if your Internet service is a DSL service. • Your ISP has given you a so-called “modem-router” instead of a simple modem. • Your ISP has not given you a username and password for PPPoE login (implying that it is not required).
management settings. Start your Web browser and log on to the router’s Web management interface by opening http://manhattanrouter, then click the “General Setup” button on the left. 2.4.1 Time Zone and Time Auto-Synchronization Click the “System” menu on the left of the Web management interface, then click “Time Zone.” You’ll be prompted to select a time zone from the “Set time zone” drop-down menu and enter the IP address or host name of the time server.
If the passwords entered in the “New Password” and “Confirmed Password” fields aren’t the same, you’ll see the message at right. Re-enter the new password. If you see the error message at right, it means the content in the “Current Password” field is wrong. Click “OK” to go back to the previous menu, and try entering the current password again. If the current and new passwords are correctly entered, click “Apply” and you’ll be prompted to log in again.
NOTE: To manage this router from another computer on the Internet, you need to input the IP address and port number of this router. If your Internet service provider assigns you a static IP address, it will not be a problem; but if the IP address your service provider assigns will vary every time you establish an Internet connection, this will be a problem. Either ask your ISP to give you a static IP address, or use a dynamic DNS service like DDNS. (See section 2.5.8 DDNS Client below for details.
2.5.1 Setup Procedure for Dynamic IP Host Name — Enter the host name of your computer. (This is optional and is only required if your service provider asks you to do so.) MAC Address — Enter the MAC address of your computer if your service provider only permits a computer with a certain MAC address to access the Internet. If you’re using the computer to connect to the Internet via cable modem, you can simply click “Clone MAC” to fill the “MAC Address” field with the MAC address of your computer. 2.5.
2.5.3 Setup Procedure for PPPoE User Name — Enter the user name assigned by your Internet service provider. Password — Enter the password assigned by your Internet service provider. Service Name — Enter a name for this Internet service. (optional) MTU — Enter the MTU value of your network connection. NOTE: Use the default value unless your ISP specifies otherwise.
entered; otherwise, the Internet connection will fail even if the PPTP settings are correct. Contact your ISP if you don’t know how you should fill in these fields. The PPTP Settings panel presents these options: User Name — Enter the username assigned by your ISP. Password — Enter the password provided by your ISP. PPTP Gateway — Enter the IP address of PPTP gateway assigned by your ISP. Connection ID — Enter the connection ID. (optional) MTU — Enter the MTU value of your network connection.
2.5.6 Setup Procedure for Telstra BigPond This procedure is only for the Telstra BigPond network service in Australia. User Name — Enter the username assigned by Telstra. Password — Enter the password assigned by Telstra. Assign login server manually — Select to choose the login server by yourself. Server IP Address — Enter the IP address of the login server. 2.5.
preferred DNS server or use a static IP address, or if your service provider didn’t assign the IP address of the DNS server for any reason, you can input the IP address of the DNS server here. Primary DNS — Enter the IP address of the DNS server provided by your ISP. Secondary DNS — Enter the IP address of the secondary DNS server provided by your ISP.
2.6 LAN Configuration This section explains the IP address settings of the local network. Normally, there is no need to make any changes here: The default values work fine for most applications, and you could just go directly to section 2.7 WLAN Configuration. There are two ways to assign IP addresses to computers: static IP address (set the IP address for every computer manually) and dynamic IP address (the IP address of computers will be assigned by the router automatically).
Subnet Mask — Enter the subnet mask for this network. 802.1d Spanning Tree — Select “Enable” or “Disable” from the drop-down menu. DHCP Server — Select “Enable” or “Disable” from the drop-down menu. RECOMMENDED VALUES IP Address: 192.168.2.1 802.1d Spanning Tree: Disabled Subnet Mask: 255.255.255.0 DHCP Server: Enabled 2.6.2 DHCP Server These settings are only available when “DHCP Server” in the LAN IP section is enabled, but will also affect wireless clients.
2.6.3 Static DHCP Leases Table This function allows you to assign a static IP address to a specific computer forever, so you don’t need to set the IP address for a computer to enjoy the benefit of using a DHCP server. A maximum of 16 static IP addresses can be assigned here.
the wireless function of this router to connect to the Internet and share resources with other computers on your network. It’s strongly recommended that you use the built-in security functions to protect your network from intruders. Click the “Wireless” menu on the left of the Web management interface to open the wireless settings page. Remeber to click “Apply” to save your settings. 2.7.1 Basic Wireless Settings Band — Select one of the options from the drop-down .menu: • “2.
• “2.4 GHz (B+G+N)” allows 802.11b, 802.11g and 802.11n wireless network clients to connect to this router (maximum transfer rate of 11 Mbps for 802.11b clients; maximum of 54 Mbps for 802.11g clients; maximum of 300 Mbps for 802.11n clients. NOTE: For optimal compatibility with wireless clients, select “2.4 GHz (B+G+N).” ESSID — Enter the name for your wireless network.
N Data Rate — Same as above, but only for 802.11n clients. Channel Width — Set the channel width of the wireless radio. NOTE: If you aren’t sure what this should be set to, leave it as the default setting (“Auto 20/40 MHz”). Preamble Type — Set the preamble type. NOTE: If you aren’t sure what this should be set to, leave it as the default setting (“Short Preamble”). Broadcast ESSID — Decide if the wireless router will broadcast its own ESSID.
card information or bank records. Click the “Security Settings” menu on the left of the Web management interface to select one of the four encryption methods from the drop-down menu (see image below). 2.7.3.1 Disable Wireless Security When you select this mode, data encryption is disabled and every wireless device in proximity will be able to connect your wireless router if no other security measure is enabled (like using MAC address access control disabling ESSID broadcast).
Default Tx Key — You can set up to four sets of WEP keys, and you can designate one as the default here. NOTE: If you don’t know which one you should use, select “Key 1.” Encryption Key 1-4 — Enter WEP key characters here. The number of characters must be the same as the number displayed n the “Key Format” field. You can use any alphanumerical characters (0-9, a-z and A-Z) if you select “ASCII” for the key format. If you select “Hex” as key the format, you can use 0-9, a-f and A-F.
2.7.3.3 Wi-Fi Protected Access (WPA) Pre-Shared Key WPA Unicast Cipher Suite — Once you select one of the three ciper options — “WPA (TKIP),” “WPA2 (AES)” or “WPA2 Mixed” — make sure your wireless clients support it. Pre-shared Key Format — Select the type of pre-shared key from the drop-down menu: “Passphrase” (8 or more alphanumerical characters, up to 63) or “Hex” (64 characters of 0-9 and a-f). Pre-shared Key — Enter the WPA passphrase.
“WPA (TKIP),” “WPA2 (AES)” or “WPA2 Mixed” — make sure your wireless clients support it. RADIUS Server IP address — Enter the IP address of the RADIUS server. RADIUS Server Port — Enter the port number of the RADIUS server. RADIUS Server Password — Enter the password of the RADIUS server. 2.7.4 Wireless Access Control This function helps to prevent unauthorized users from connecting to your router: Only those wireless devices that have the MAC address you assign here can gain access.
“aa-bb-cc-dd-ee-ff” or “aa:bb:cc:dd:ee:ff,” just enter “aabbccddeeff” (without the quote marks). Comment — This is optional and can be left blank, but it’s recommended that you enter something (such as “My Desktop,” as shown) that will help you identify an address later. Add — Click to add the MAC address and associated comment to the MAC Address Filtering table. Clear — Click to remove whatever you entered in the “MAC Address” or “Comment” fields. 2.7.
to connect to this wireless router. Click the “Wireless” menu on the left of the Web management interface, then click “WPS.” Enable WPS Settings — Check the box to enable the function; uncheck to disable. Enable WPS Proxy — Check the box to enable the function; uncheck to disable. When enabled, it allows another access point to serve as an “intermediary” device for the connection between wireless network clients and the router.
WPA or WPA2, you should abandon WEP entirely. • You can hide the ESSID of this router by setting the “Broadcast ESSID” option (refer to section 2.7.2.Advanced Wireless Settings) to “Disable.” Once this option is disabled, the router will no longer broadcast the SSID; thus, wireless clients in the area will not be able to see the wireless network in the list of available WLAN networks.
3 ADVANCED FUNCTIONS 3.1 Quality of Service (QoS) Quality of service provides an efficient way for computers on the network to share the Internet bandwidth with a promised quality of Internet service. Without QoS, all computers and devices on the network compete with each other to get Internet bandwidth, and some applications which require guaranteed bandwidth (like video streaming and network telephone) are affected negatively, resulting in an interruption of video/audio transfers.
Current QoS Table — All existing QoS rules are shown here. Add — Click to add new QoS rules (see section 3.1.2 Adding a New QoS Rule). Edit — To modify the content of a specific rule, check the “Select” box of that rule, then click “Edit.” NOTE: Only one rule should be selected at a time. If you didn’t select a rule before clicking “Edit,” you’ll be prompted to add a new rule.
Local IP Address — Specify the local (source) IP address that will be affected by this rule. Enter the starting IP address in the left field, and enter the end address in the right field to define a range of IP addresses; or just enter the IP address in the left field to define a single IP address. Local Port Range — Enter the range of local (source) port numbers that should be affected by this rule.
Click the “NAT” menu on the left of the Web management interface. NAT is enabled by default, and there is normally no need to change this. 3.2.1 Port Forwarding With this function, you can tell the router to forward incoming connections bound to a specific port or port range to an IP address on your local network.
Type — Select the type of connection from the drop-down menu: “TCP,” “UDP” or “Both.” If you’re not sure which to use, select “Both.” Port Range — Enter the starting port number in the left field and enter the ending port number in the right field. To redirect a single port number, just enter the port number in the left field. Comment — Enter text to describe this mapping, using up to 16 alphanumerical characters; e.g., “camera web port.” Add — Add the mapping to the Current Port Forwarding Table.
Private IP — Enter the IP address of the computer on the local network that provides Internet service. Computer Name — With all the computers connected to the router listed in this drop-down menu, you can select a name without checking its IP address. Private Port — Enter the port number of the IP address that provides Internet service. Type — Select the type of connection from the drop-down menu: “TCP,” “UDP” or “Both.” If you’re not sure which to use, select “Both.
Current Trigger-Port Table — All the settings for the specifal applications are listed here. Delete — To remove a Special Application setting from the Current Trigger-Port Table, select the setting and click “Delete.” Delete All — Click to delete all existing specifal application settings. 3.2.4 UPnP This function enables network auto-configuration for peer-to-peer communications.
3.3 Firewall In addition to the NAT feature, this router provides firewall functionality to block malicious intruders from accessing the computers on your local network. Click the “Firewall” menu on the left of the Web management interface. Firewall Module — Check to enable this function; uncheck to disable. 3.3.1 Access Control This function allows or denies computers with a specific MAC address — or a specific IP address, protocol or port — access to the network.
address label of your device reads “aa-bb-cc-dd-ee-ff” or “aa:bb:cc:dd:ee:ff,” just enter “aabbccddeeff” (without the quote marks). Computer Name — With all the computers connected to the router listed in this drop-down menu, you can select a name without checking its IP address. Comment — Enter up to 16 alphanumerical characters to identify the MAC address, such as “Room 2A Computer.” This is optional, and you can leave it blank.
3.3.2 Add PC Clicking “Add PC” on the Access Control screen will display this page. Client PC Description — Enter up to 16 alphanumerical characters to describe this IP address. Client PC IP Address — Enter the starting IP address in the left field and the end IP address in the right field to define a range of IP addresses, or just input the IP address in the left field to define a single IP address. Client PC Service — Select all services you want to allow or deny through this IP address.
Protocol — If the service you need is not listed, you can create a new service yourself. Select “TCP” or “UDP” from the drop-down menu and follow the Port Range instructions below. If you’re not sure .which Protocol to use, select “Both.” Port Range — Enter the port range of the new service. To specify ports 80 to 90, enter “80-90”; to apply this rule to a single port, just enter the port number. Add — Click to save the settings.
“http://www.blocked-site.com” or “http://11.22.33.44”), or a keyword contained in a URL (like “pornography,” “sex,” “banner advertisement,” etc). Add — Click to add the URL/keyword to the URL/Keyword Filtering Table. Reset — Click to remove all entries in the “URL/Keyword” text field. Current URL Blocking Table — All existing URL/keywords in the filtering table. Delete — Select a URL/keyword by checking the “Select” box of the entry, then clicking “Delete.
and the router will filter this kind of traffic out. Advanced Settings — Click to set advanced settings of the DoS prevention method listed above. (See section 3.3.4.1 DoS – Advanced Settings below.) 3.3.4.1 DoS – Advanced Settings Clicking “Advanced Settings” on the first DoS Module screen will display this page. Ping of Death — Set the threshold of when this DoS prevention mechanism will be activated.
Enable DMZ — Check to enable this function; uncheck to disable. Public IP — Select “Dynamic IP” or “Static IP.” If you select “Dynamic IP,” you need to select an Internet connection session from the drop-down menu; if you select “Static IP,” enter the IP address that you want to map to a specific private IP address. Client PC IP Address — Enter the private IP address that the Internet IP address will be mapped to. That is the computer you want to bypass the firewall and NAT.
4 ADDITIONAL FUNCTIONS/FEATURES 4.1 Status This screen and the submenus that can be accessed from here show information about the firmware version of the router, the Internet connection, IP address information, log files and more. Click the “Status” link at the upper-right corner of the Web management interface.
This screen shows IP address information the router has obtained. If you experience problems with your Internet connection, open this page and check the contents. Values for IP address, default gateway and primary DNS should always be filled. If they’re missing, it indicates that there is a connection problem preventing the router from accessing the Internet. 4.1.
4.1.5 Active DHCP Client If you’re using the DHCP server function of this router, you can use this function to check all active DHCP leases issued by this router. 4.1.6 Statistics Statistics of the wireless LAN, wired LAN and WAN interface of the router are shown on this screen. Refresh — Click to display the latest information. NOTE: The information is accumulative and is only reset after the router is restarted. 4.
reload it at a later time. You can save different configurations, each with unique settings, and reload them as needed. Backup Settings — Click “Save...” and you’ll be prompted to download the configuration as a file (the default filename is “default.bin”). Remember to save it as another filename each time you back up for easier retrieval of information..
Browse — Click to locate the firmware file you’ve downloaded. If the file is in Zip (compressed archive) format, you need to uncompress .it prior to the upgrade. Apply — Click to start the firmware upgrade process. Never interrupt the upgrade process by closing the Web browser or by physically disconnecting your computer from the router. If the upgrade process is interrupted by a network problem or a power failure, the router will cease to function.
5 TROUBLESHOOTING This section helps you troubleshoot problems you may be experiencing with the router. Before you contact your dealer for help, you should perform the following troubleshooting steps as they apply to your situation. The router is not responding when I want to access it with the Web browser. • Check the power connection and the connection of the network cable. All cords and cables should be correctly and firmly inserted into the router.
My wireless notebook cannot see or connect to the wireless network. • Check if Broadcast ESSID is off. Remember that you need to input the ESSID on your wireless client manually if the ESSID broadcast is disabled. • Check that you’ve securely attached the antenna(s). • Make sure that you’re not too far away from the router. I can’t log on to the Web management interface: The password is wrong. • Make sure you’re connecting to the correct IP address of the router. • The password is case-sensitive.
6 GLOSSARY Default Gateway (Router): Every non-router IP device needs to configure a default gateway’s IP address. When the device sends out an IP packet, if the destination is not on the same network, the device has to send the packet to its default gateway, which will then send it out toward the destination. DHCP: Dynamic Host Configuration Protocol. This protocol automatically gives every computer on your home network an IP address.
ISP: Internet Service Provider. An ISP is a business that provides connectivity to the Internet for individuals and other businesses or organizations. LAN: Local Area Network. A LAN is a group of computers and devices connected together in a relatively small area (such as a house or an office). Your home network is considered a LAN. MAC Address: MAC stands for Media Access Control.
manhattan-products.com © IC Intracom. All rights reserved. Manhattan is a trademark of IC Intracom, registered in the U.S. and other countries.
