Owner manual

ManualsBrandsMalone ManualsHardwareMPG113MD

Table Of Contents

MALONE

SS ComboSS Combo

SEAWING KAYAK CARRIER with

STINGER LOAD ASSIST

Extension Frame Mounting Plate V-Block 70mm Bolts

Stinger Load Assist Components

Installation & Loading Instructions - Please Read Before Beginning

. Insert the two 1” bolts into the two holes

located on the bottom side of the Extension

Frame. Tighten with a phillips screwdriver.

See image 2.

Step 1: Stinger Pre-Assembly

. Place the V-Block into the channel located directly

behind the Malone logo on the Extension Frame.

See image 1.

12’ Safety Lines

MD Series Only

Jawz Universal Adapters Mounting Bolts

60mm

50mm

SeaWing Kayak Carriers 12’ Load Straps

T-Knobs

Rubber Plugs

SeaWing Kayak Carrier Components

T-knobs

1” Bolts1 3/4” Bolts

Summary of content (10 pages)

PAGE 1
MALONE R SS Combo TM SEAWING KAYAK CARRIER with STINGER LOAD ASSIST TM TM T-knobs 1 3/4” Bolts Extension Frame Mounting Plate V-Block 1” Bolts 70mm Bolts Stinger Load Assist Components TM 50mm Rubber Plugs 60mm SeaWing Kayak Carriers TM 12’ Load Straps Jawz Universal Adapters Mounting Bolts T-Knobs 12’ Safety Lines MD Series Only SeaWing Kayak Carrier Components TM Installation & Loading Instructions - Please Read Before Beginning 1 Step 1: Stinger Pre-Assembly .
PAGE 2
MALONE R Installation & Loading Instructions - MPG113MD SS Combo TM 3 . Place the Extension Frame on top of the Mounting Plate with the raised block side facing up. The two holes located on the end of the Plate should align with the two channels in the Frame. See image 3. Align channels to holes 4 . Insert the 1 3/4” Carriage Bolts down and through the Extension Frame channels and into the holes in the Mounting Plate. See image 4. 5 . Loosely thread the two T-knobs onto the Bolts.
PAGE 3
MALONE R Installation & Loading Instructions - MPG113MD SS Combo TM 7 . Insert a single 70mm Mounting Bolt down through the SeaWing and Mounting Plate. See image 7. . Insert Bolt through one hole of the Jawz mounting adapter and loosely apply the T-knob. See image 8. 8 Note: Additional bolt lengths available. 9 . Place the Stinger with SeaWing assembly onto the rear cross bar of the vehicle with the V-Block closest to the rear of the vehicle.
PAGE 4
MALONE R Installation & Loading Instructions - MPG113MD SS Combo TM 11 . Using the second SeaWing carrier, insert a Mounting Bolt into one of the top side hex holes. See image 11. 12 . Insert Mounting Bolt through one hole of a Jawz Mounting Adapter and loosely apply a T-knob. See image 12. 13 . Place the carrier onto the front cross bar. Swing the Jawz under the cross bar as shown. See image 13. 14 .
PAGE 5
MALONE R Installation & Loading Instructions - MPG113MD SS Combo TM 15 . Confirm the carriers are in alignment. Firmly tighten the T-knobs until both carriers are securely fixed to the cross bars. See image 15. 16 . Insert the four Rubber Plugs into the four top side hex holes in the two carriers. See image 16. 17 Step 3: Loading the Kayak . Route the free end of a 12’ Load Strap down through the top of the outer most strap slot and back up through the inside slot of the carrier.
PAGE 6
MALONE R Installation & Loading Instructions - MPG113MD SS Combo TM . Loosen the two T-knobs holding the Extension Frame. Pull the Frame out to the rear edge of the vehicle and slightly re-tighten the T-knobs. See image 19. 19 Note: The Extension Frame will bend down under the weight of the kayak. The Frame should be placed so that the rubber pad makes contact with the vehicle’s rear edge. This will provide support and protection while the kayak is loaded. 20 .
PAGE 7
MALONE R Installation & Loading Instructions - MPG113MD SS Combo TM 23 . Position kayak so that the cockpit is evenly centered between the front and rear carriers. The bottom of the kayak should be slightly elevated above each of the carriers and held by the sides of the carriers. See image 23. 24 . Place the strap loops over the kayak so that each loop is positioned directly over a carrier. See image 24. 25 .
PAGE 8
MALONE R Installation & Loading Instructions - MPG113MD SS Combo TM 26 . Thread the free strap ends up and through the buckles. Pull down to tighten. Dress any extra strap down and around the cross bars. See image 26. . For MD series only: Install the bow & stern safety lines per the attached instructions. IMPORTANT NOTES: Safety tie-downs are required for all transport. If your kit did not include safety tie-downs, we strongly recommend the use of the Malone MPG316 Sentry Ratchet Tie-Down System.
PAGE 9
MALONE R MPG370 BOW & STERN LINE KIT Attach hook to rope (steps A-D) A Thread free end of cord through hook. B C Create a “left over right” knot & tighten. D Create a “right over left” knot & tighten. Pull to test for knot strength. Attach and dress rope to vehicle and boat (steps E-O) E Attach S-hook to vehicle tow ring or other sturdy body part. F Keeping the rope tight and S-hook in place, thread the free end up and through a strong point on the kayak I Pass the loop through the opening.
PAGE 10
MALONE R Limited Lifetime Warranty The Malone Auto Racks (Malone) Limited Lifetime Warranty covers certain Malone-brand products that have been specifically identified for inclusion in the program and is effective for as long as the original retail purchaser owns the product. This warranty is terminated when the original retail purchaser sells or otherwise transfers the product to any other person or entity.