User Guide

71 1/98
TAILLIGHT DOES NOT WORKTAILLIGHT DOES NOT WORK
TAILLIGHT DOES NOT WORKTAILLIGHT DOES NOT WORK
TAILLIGHT DOES NOT WORK
1) Check for continuity of the bulb and bulb holder (tester set to O H M ).
In case of
discontinuitydiscontinuity
discontinuitydiscontinuity
discontinuity replace the bulb and/or the bulb holder.
In case of
continuitycontinuity
continuitycontinuity
continuity :
2) Check voltage at the bulb holder with a tester set to 20V AC by connecting:
the (
++
++
+ ) terminal of the tester to the
pinkpink
pinkpink
pink cable, and
the (
--
--
-) terminal of the tester to the
blackblack
blackblack
black cable.
3) Start up the engine and run at (7.000 rpm).
4) Check voltage between the
pink pink
pink pink
pink and
black black
black black
black cables (12V).
If reading is other than the above:If reading is other than the above:
If reading is other than the above:If reading is other than the above:
If reading is other than the above:
5) Check for continuity of the
pinkpink
pinkpink
pink cable between the main switch and the rear bulb holder as well as earth continuity
of the
blackblack
blackblack
black cable.
LE FEU ARRIERE NE FONCTIONNE PASLE FEU ARRIERE NE FONCTIONNE PAS
LE FEU ARRIERE NE FONCTIONNE PASLE FEU ARRIERE NE FONCTIONNE PAS
LE FEU ARRIERE NE FONCTIONNE PAS
1) Vérifier la continuité de l’ampoule et de la douille (testeur en position OHM)
Discontinuité:Discontinuité:
Discontinuité:Discontinuité:
Discontinuité:
Remplacer l’ampoule et/ou la douille
Continuité:Continuité:
Continuité:Continuité:
Continuité:
2) Vérifier la tension sur la douille
(testeur en c.a. 20V)
borne du testeur (
++
++
+ ) > au câble
roserose
roserose
rose
borne du testeur (
--
--
-) > au câble
noirnoir
noirnoir
noir
3) Mettre le moteur en route (7.000 tours/mn)
4) Contrôler la tension (12V) entre les câbles
roserose
roserose
rose et
noirnoir
noirnoir
noir .
Valeur hors spécifications:Valeur hors spécifications:
Valeur hors spécifications:Valeur hors spécifications:
Valeur hors spécifications:
5) Vérifier la continuité du câble
roserose
roserose
rose entre l’interrupteur général et la douille arrière.
Vérifier aussi la continuité de masse du câble
noirnoir
noirnoir
noir .
LA LUZ TRASERA NO FUNCIONALA LUZ TRASERA NO FUNCIONA
LA LUZ TRASERA NO FUNCIONALA LUZ TRASERA NO FUNCIONA
LA LUZ TRASERA NO FUNCIONA
1) Verificar la continuidad de la bombilla y del casquillo (Tester en OHM)
Discontinuidad:Discontinuidad:
Discontinuidad:Discontinuidad:
Discontinuidad:
Sustituir la bombilla y/o el casquillo.
Continuidad:Continuidad:
Continuidad:Continuidad:
Continuidad:
2) Controlar la tensión en el casquillo
(tester c.a. 20V):
borne del tester (
++
++
+ ) > al cable
rosarosa
rosarosa
rosa
borne del tester (
--
--
-) > al cable
negronegro
negronegro
negro
3) Poner en marcha el motor (7.000 rev./min.)
4) Verificar la tensión (12V) entre los cables
rosa rosa
rosa rosa
rosa y
negronegro
negronegro
negro.
Valor fuera de las especificaciones:Valor fuera de las especificaciones:
Valor fuera de las especificaciones:Valor fuera de las especificaciones:
Valor fuera de las especificaciones:
5) Verificar la continuidad del cable
rosarosa
rosarosa
rosa entre el interruptor general y el casquillo trasero.
Verificar también la continuidad de tierra del cable
negronegro
negronegro
negro.