Use and Care Manual

4 ENGLISH
Oblong punching
Punch Die Workpiece Capacity
Flat bar Max: 80 mm (3-5/32″) x t8
(Center punching)
Angle
Min: 40 mm (1-37/64″) x 40 mm (1-37/64″) x t3
Max: 80 mm (3-5/32″) x 80 mm (3-5/32″) x t8
Channel
Min: 75 mm (61/64″) x 40 mm (1-37/64″)
Max: 100 mm (3-15/16″) x 50 mm (1-31/32″)
(Flange punching)
Unit: mm
Punch Die Tensile Channel Tensile
Mild Steel (65,000 psi) Stainless Steel (89,000
psi)
6.5 x 10
(1/4″ x 3/8″)
6.5 x 10B
(1/4″ x 3/8″-B) t2 - t6 - t3 - t4
6.5 x 13
(1/4″ x 1/2″)
6.5 x 13B
(1/4″ x 1/2″-B) t2 - t6 - t3 - t4
8.5 x 13
(11/32″ x 1/2″)
8.5 x 13B
(11/32″ x 1/2″-B) t2 - t6 - t3 - t4
8.5 x 17
(11/32″ x 43/64″)
8.5 x 17B
(11/32″ x 43/64″-B) t2 - t6 - t3 - t4
9 x 13.5
(23/64″ x 17/32″)
9 x 13.5B
(23/64″ x 17/32″-B) t2 - t6 - t3 - t4
9 x 18
(23/64″ x 23/32″)
9 x 18B
(23/64″ x 23/32″-B) t2 - t6 - t3 - t4
10 x 15
(3/8″ x 19/32″)
10 x 15B
(3/8″ x 19/32″-B) t2 - t8 t7.5 t3 - t6
10 x 20
(3/8″ x 25/32″)
10 x 20B
(3/8″ x 25/32″-B) t2 - t8 t7.5 t3 - t6
11 x 16.5
(7/16″ x 21/32″)
11 x 16.5B
(7/16″ x 21/32″-B) t2 - t8 t7.5 t3 - t6
12 x 18
(15/32″ x 23/32″)
12 x 18B
(15/32″ x 23/32″-B) t2 - t8 t7.5 t3 - t6
13 x 19.5
(1/2″ x 49/64″)
13 x 19.5B
(1/2″ x 49/64″-B) t2 - t8 t7.5 t3 - t6
14 x 21
(9/16″ x 53/64″)
14 x 21B
(9/16″ x 53/64″-B) t2 - t8 t7.5 t3 - t6
Symbols
The followings show the symbols used for the equip-
ment. Be sure that you understand their meaning before
use.
Read instruction manual.
Flying debris and loud noise hazards. Wear
ear and eye protection.
Hazardous voltage. Disconnect all power
before working on this equipment. Failure
to observe this instruction may result in
death or personal injury.
Moving blade. Keep hands clear while
machine is operating. Turn power off
before servicing.