Cordless Angle Drill 10 mm (3/8") MODEL DA3000D 10 mm (3/8") MODEL DA3000DW With Fast Charger INSTRUCTION MANUAL SPEC IFICAT10NS M o d e l DA3000D Capacities SteelIWood Wood screw 10 mm 13/8"1 4 5 mm x 2 0 mm 13/16" x 3/4"1 Battery Cartridge 7000 Voltage Charging time 7 2 V 1 Hr. No load speed Net weight Overall length 700 Rimin 1 2 kg 12 6 lbsl 290 mm 11 1-3/8"1 M o d e l DC7100 Fast Charger input A.C. only 60 Hr 5 0 H2 OUtPUt 0.
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp 3. 4. 5. 6. 7. 0. 9. IO. 11. 12. 13. 2 or wet locations. Keep work area well lit. Don't expose power tools t o rain.
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o 15. 16. 17. 18. 19. 20. see that keys and adjusting wrenches are removed from tool before turning it on. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. STAY ALERT. Watch what you are doing, use common sense.
IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS - This manual 2. 3. 4. 5. 6. 7. 8. Length of Cord (Feet) 25 AWG Size of Cord 18 50 18 100 18 150 16 9.Do not operate charger with damaged cord or plug - replace them immediately. IO. Do not operate charger if it has received a sharp blow, been dropped, or otherwise damaged in any way; take it t o a qualified serviceman. 1 1 .
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. 3.Do not allow anything t o cover or clog the charger vents. 4. Do not short the battery cartridge. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. 5.
Installing or removing battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. 0 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. I Set plate I *To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place.
Installing and removing bit CAUTION : Be sure that the battery cartridge has been removed from the tool. .To install the drill bit, place it in the chuck as far as it will go. Tighten the chuck collar by hand. Place the chuck key in each of three holes, and tighten clockwise. To remove the drill bit, place the chuck key into the chuck hole and turn counterclockwise. Tighten CAUTION: Always set the Forward-Reverseswitch lever to NEUTRAL when installing, removing or adjusting bits or accessories.
Switch action o s e t the reversing switch lever just in front of the trigger switch to Forward (FWD) or Reverse (REV). Then pull the trigger to turn the tool ON and release it to turn it OFF. To change the direction of bit rotation, release the trigger, let the tool come to a complete stop, and then slide the switch lever to the opposite side. The trigger switch does not work if the switch lever is in the neutral position.
0 Use cutting lubricant on the bit to facilitate! drilling if necessary. Screwdriving Phillips bits Select your screws and nominal diameter with the chart on the right. Item Nominal Diameter (mm) B i t No. Wood Screw 2.1 - 2.7 (3/32" - 1/8") 3.1 - 4.5 (1/8" - 3/16") Slotted bits Select a slotted bit to match the slot on the screw heads. If the bit is too small for the screw slot, the bit and/or screw head may be damaged.
Hole .The hole on the heel of the tool is a convenient way to carry it by a cord, hook or other means.
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.
ACCESS0 R I ES CAUTION : These accessories or attachments are recommended for use w i t h your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner. 0 Bits Square drill b i t 0 [ 784606-0A 0 Fast charger Model DC7100 0 12 V Fast charger Model DC7012 0 Battery cartridge 7000 Part No. 632003-2 0 Chuck key Part No.
0 Steel case Part NO.
Sep-19284 US 10 mm (3/8") CORDLESS ANGLE DRILL Model DA3000D Note: The switch and other part configurations may differ from country to country.
MODEL OA30000 'ikM Aug.-09-'84 & !, DESCRIPTION 1 1 2 3 4 5 6 7 1 1 1 1 1 1 8 1 Orill Chuck 5 1 0 0 Ring 34 Plane Bearing 5 Housing Set IWnh Item 11 ) Holder 6 Gear Plane 0earmg 4 Current Relay 9 10 11 13 14 15 16 24 US DESCRIFTION 1 Switch 1 1 tioUSlng Set w t h Item 4 1 1 9 1 Name Plate Screw M4x22 [With Washer1 Set Plate 1 2 Battery 7000 Rivet 0 - 5 Motor Note: The switch and other part specifications may differ from country to country.
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.
