User Manual

ManualsBrandsMakeSkyBlue ManualsEnergy Controllers60A MPPT Charge Controller, LCD Display, Auto 12V/24V/36V/48V Solar System

USER MANUAL OF MPPT SOLAR CHARGE CONTROLLER

For Models: S3-30A, S3-40A, S3-50A, S3-60A

Important note

All expressed or written warranties shall be deemed void if controller has been

opened, disassembled, altered or used in any manner inconsistent with written

instructions. All warranties shall also be deemed void if controller is overpowered,

input PV polarity reversed or battery polarity reversed. It’s user’s responsibility to

control input wattage and connect all polarity correctly to avoid damaging controller.

Features

 30A/40A/50A/60A MPPT solar charge controller

 MPPT technology

 Built-in High Performance DSP controller

 Automatic battery voltage detection for 12V/24V/36V/48V

 3-stage charging optimizes battery performance

 The MPPT track speed is 5 times faster than traditional controllers

 The charging voltage accuracy is ± 0.2V

 Output limited current protection, Overcharge protection, Over-temperature protection

 Suitable for battery types such as lead acid, vented gel, and lithium battery, etc

Basic Parameter

Models

S3-30A

S3-40A

S3-50A

S3-60A

Battery voltage automatic recognition

12V system: 9V-15V; 24V system: 18V-29V

36V system: 30V-39V; 48V system: 40V-60V

Overcharging protection voltage

12V Bat: 15V; 24V Bat: 30V;

36V Bat: 45V; 48V Bat: 60V

Limited current protection

31A

42A

51A

61A

Max efficiency

≥98.2%

PV utilization

≥99%

Summary of content (8 pages)

PAGE 1
USER MANUAL OF MPPT SOLAR CHARGE CONTROLLER For Models: S3-30A, S3-40A, S3-50A, S3-60A Important note All expressed or written warranties shall be deemed void if controller has been opened, disassembled, altered or used in any manner inconsistent with written instructions. All warranties shall also be deemed void if controller is overpowered, input PV polarity reversed or battery polarity reversed.
PAGE 2
Protection function Temperature protection 75℃ / 167℉ Fan-on temperature >45℃ / 113℉ Fan-off temperature <40℃ / 104℉ Properties Dimensions 214x115x50mm / 8.4*4.5*1.97in Net weight 1.2KG / 2.
PAGE 3
How choose Two-pole Circuit Breaker and Wires Models S3-30A S3-40A S3-50A S3-60A Pure copper wires 6mm²/9AWG 6mm²/9AWG 2PCS 6mm²/9AWG 2PCS 6mm²/9AWG Circuit Breaker 2PCS 63A 2PCS 63A 2PCS 63A 2PCS 100A Warning  Be aware that only qualified professionals should install these controllers. Please read full manual before installing. Please don’t set any parameters if you are not a professional installer. The controller will work well on defaults for Lead acid.
PAGE 4
Reminder  The battery voltage must be over 12V, then can start up the controller.  Keep controller in an environmental temperature of -22℃~+55℃. Avoid direct sunlight.  Keep good heat dissipation.  Please contact us or authorized distributor if any doubts before installation or any errors after installed. Installation steps 1. Use one two-pole circuit breaker in “OFF” position. Install this circuit breaker between controller and battery. Connect batteries to controller ensuring correct polarity.
PAGE 5
Controller PV+ Two-pole Circuit breaker+ Controller PV- Two-pole Circuit breaker- Solar- Controller BT+ Two-pole Circuit breaker+ Battery+ Controller BT- Two-pole Circuit breaker- Controller OU+ Two-pole Circuit breaker+ Controller OU- Two-pole Circuit breaker- Solar+ BatteryDC Load+ DC Load- How to make controllers in parallel Make sure all wires are same size and length.
PAGE 6
LCD display Working mode 1 PV voltage / Output power 3.0 Night mode, no charging 2 Battery voltage / Charging current 4.0 MPPT mode 3 Working mode/Error code/Temperature 7.0 Absorption mode 4 ACC Power Generation 8.
PAGE 7
3. D02 Continue to press the button UP, LCD shows 14.5 (Voltage can be set from 12V17V). This is highest constant voltage for battery. Press ENTER until numbers flash, then press UP/DOWN to set up voltage that you want, press ENTER to confirm it. 4. D03 Continue to press the button UP, LCD shows 10.0. This is protection value of battery discharge. Press ENTER until numbers flash, then press UP/DOWN to set up voltage that you want, press ENTER to confirm it.
PAGE 8
Batteries charge voltage reference Battery Absorption Voltage ( Constant voltage ) Floating Voltage 12V 24V 48V 12V 24V 48V Vented 14.2V 28.6V 57.2V 13.2V 26.4V 52.80V Sealed 14.4V 28.8V 57.6V 13.8V 27.6V 55.2V Gel 14.4 V 28.8V 57.6V 13.8V 27.6V 55.2V NiCd 14.2V 28.6V 57.2V 14.0V 28.0V 56.0V Lithium If your battery voltage range is 9-15V, then it's 12V system, you can set Or special controller charging voltage from 12V-17V.