Instructions

ManualsBrandsMAKERFACTORY Manuals3D Printer Spares & AccessoriesNozzle Suitable for (3D printer): Makerfactory UN-400B 3D Pen

b) Open Nozzle Cover

• Carefully press a small flat tool (e.g. flathead screwdriver) against the nozzle cover release

tab (3) or (5).

c) Remove Old Nozzle Assembly

• Use your fingers to carefully pull the old

nozzle assembly out, wiggling carefully

if you encounter resistance.

d) Open Handle Cover

• Grip the 3D pen as shown and apply a gentle “snapping“ motion to “pop” the handle cover (4) off.

e) Insert New Nozzle Assembly

• Slide the tube through the feeder all the way back through the hole underneath the motor.

• Line the pins on the tip with the holes in the body and carefully insert all the way flush.

f) Attach Handle and Nozzle Cover

Attach Handle Cover

• First insert the rear cover pin (A), then snap the cover shut (B).

Re-Attach Nozzle Cover

An extra nozzle cover (2) has been included as a spare.

• Line both nozzle cover (2) release tabs (3) and (5) up with the slots in the casing and gently

lock into place.

Disposal

At the end of its service life, dispose of the product in accordance with applicable

regulatory guidelines. You thus fulll your statutory obligations and contribute to the

protection of the environment.

Technical Data

Nozzle tip ...................................... ø 0.7 mm

Nozzle material ............................. Ceramic

Operating conditions ..................... -5 to +50 °C, 20 – 85 % RH

Storage conditions ........................ -10 to +50 °C, 20 – 85 % RH

Operating Instructions

Nozzle for 3D Printing Pen UN-400B

Item no. 1885103

Intended Use

The product is a replacement part for a broken

or blocked nozzle.

This product is intended for indoor use only.

Do not use it outdoors. Contact with moisture

(e.g. in bathrooms) must be avoided under all

circumstances.

For safety and approval purposes, you must

not rebuild and/or modify this product. Using

the product for purposes other than those

described above may damage the product.

In addition, improper use can cause hazards

such as a short circuit, fire or electric shock.

Read the instructions carefully and store them

in a safe place. Make this product available

to third parties only together with its operating

instructions.

This product complies with statutory national

and European regulations. All company

and product names are trademarks of their

Delivery Content

• Nozzle cover (spare)

• Nozzle assembly

• Operating Instructions

Up-to-Date Operating Instructions

Download the latest operating instructions at

www.conrad.com/downloads or scan the QR

code on this page. Follow the instructions on

the website.

Safety Instructions

Read the operating instructions carefully

and especially observe the safety

information. If you do not follow the safety

instructions and information on proper

handling in this manual, we assume no

liability for any resulting personal injury

or damage to property. Such cases will

invalidate the warranty/guarantee.

a) General

• The product is not a toy. Keep it out of the

reach of children and pets.

• Do not leave packaging material lying

around carelessly. This may become

dangerous playing material for children.

• Protect the product from extreme

temperatures, direct sunlight, strong jolts,

high humidity, moisture, flammable gases,

steam and solvents.

• Do not place the product under any

mechanical stress.

• If it is no longer possible to operate the product

safely, take it out of operation and protect it

from any accidental use. Safe operation can

no longer be guaranteed if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in

poor ambient conditions or

- has been subjected to any serious

transport-related stresses.

• Please handle the product carefully. Jolts,

impacts or a fall even from a low height can

damage the product.

• Also observe the safety and operating

instructions of any other products which are

connected to the product.

• Consult an expert when in doubt about the

operation, safety or connection of the product.

• Maintenance, modifications and repairs

must only be completed by a technician or

an authorised repair centre.

• If you have questions which remain

unanswered by these operating instructions,

contact our technical support service or

other technical personnel.

b) Replacing Nozzle

• Warning! The pen tip is very hot during

operation. Do not touch! Risk of burns!

• Never touch the nozzle or the rubber area

at the pen tip during and immediately after

operation.

• The extruded filament is very hot for a short

time. Do not touch! Risk of burns!

• Disconnect the device from the power

supply, turn the power off, and allow to cool

before attempting to replace the nozzle.

Overview

1 2 3

1 Nozzle

2 Nozzle cover

3 Nozzle cover release tab

4 Handle cover

5 Nozzle cover release tab

6 Feeder opening

Replacing Nozzle Assembly

Allow the device to cool down completely before attempting to replace nozzle.

Switch the power off on the pen and disconnect from the power supply.

a) Jammed Filament

If lament is jammed do not use force to pull it out from the feeder opening (6), this may

damage the motor. Use scissors to cut away any excess at the feeder opening (6) and

pull it through from the inside after removing the handle cover (4).

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method (e.g. photocopying, microlming, or the capture in

electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.

This publication represents the technical status at the time of printing.