PABX Telephone Switching System User Manual v1.02 PABX TELEPHONE SWITCHING SYSTEM USER MANUAL Model 416-832 Extendible PABX System ©2012 Makati Corporate Office Services Inc. is located at 28th Floor, Cityland Pasong Tamo Tower, 2210 Chino Roces Avenue, Makati CIty, Philippines 1200. Trunkline +63 2 893-8909.
PABX Telephone Switching System User Manual v1.02 PRECAUTIONS PLEASE KEEP ALL CHILDREN AWAY FROM THIS EQUIPMENT! ONLY CONNECT TO STANDARD 220V/110 VAC 60 HZ – USE AVR TO ENSURE STABLE POWER. POWER THAT HAS STANDARD 3 PRONG GROUNDED POWER OUTLET. NEVER RETROFIT OR FORCE THE PLUG INTO A POWER OUTLET. AVOID ALL LIQUID SPILLS ONTO THE UNIT - IF WATER OR ANY LIQUID SPILLS INTO UNIT, DISCONNECT FROM POWER IMMEDIATELY.
PABX Telephone Switching System User Manual v1.02 ADVANCED FUNCTION LIST The PBX's are compatible with almost all standard single and multi line touch tone phones. (multi line phones use multi extensions). A single line phone has access to all CO lines incoming and outgoing calls essentially turning a single line phone into a 4 line phone. Transfering and holding of calls are performed using the flash button.,or *.
PABX Telephone Switching System User Manual v1.02 B. SYSTEM TRANSFER MODE SETTING 1.The system has two mode of transfering the CO.line call.By flash or by pressing *,in the default setting,the system is on the mode of patting hook switch for transfering.You can change the mode by programming: Enter the programming state on Ext.600, 52 ABC 1# 52 ABC 0# To transfer the call by pressing *. To transfer the call by patting hook switch or R button. When ABC is ***,it means all extensions. 2.
PABX Telephone Switching System User Manual v1.02 has entered into PBX System programming state. Then you can do the following programming. To exit the system programming state, please dial 999999# or hang up the handset for over 10 seconds. SECTION ONE: CO Line Function Programming Explanation: 1. In the programming, reference is made to daytime service and night service. This must be switched from one state to the other by the operator.
PABX Telephone Switching System User Manual v1.02 Code:62 m 0# Explanation: The m CO line is on operator assistant in night service state. Example: Set the second CO line for Operator assistant in daytime service state, while auto attendant in night service state. Code: 61 02 0# hear dialing tone, Code: 62 02 1# hear dialing tone, then hang up handset. Item 3. To set extension ringing state when CO line calls in Code:1 m abc 1# Explanation: Operator assistant on daytime service state and Ext.
PABX Telephone Switching System User Manual v1.02 Explanation: FORBID Ext. abc dialing out using the m CO line. Code:3 m abc 0# Explanation: Permit Ext. abc dialing out using the m CO line. Item 6. To set extension dialing out mode Code:51 abc 1# Explanation: Ext.abc dials out directly. Code:51 abc 0# Explanation: Ext.abc dials out by dialing 9 first (default). Item 7. Transfering the extension Code:52 abc 1 # Explanation:Ext.abc transfering by pressing “ * ” Code:52 abc 0 # Explanation:Ext.
PABX Telephone Switching System User Manual v1.02 Item 11. To FORBID extension dialing out with restrict number call (see Item 21) Code:44 abc 1# Explanation: FORBID Ext.abc dialing out with restricted number call. Code:44 abc 0# Explanation:Permit Ext.abc dialing out with restricted number call. Item 12.To permit extension dialing out with specific number call (see Item 22) Code:45 abc 1# Explanation: FORBID Ext.abc dialing out with the specific number call. Code:45 abc 0# Explanation:Permit Ext.
PABX Telephone Switching System User Manual v1.02 Item 16. To set call duration of extension Code:54 abc 1# Explanation:The call duration of Ext.abc should be no longer than 3 minutes. Code:54 abc 0# Explanation:NO restriction for the call duration of Ext.abc. Code:55 abc 1# Explanation:The call duration of Ext.abc should be no longer than 5 minutes. Code:55 abc 0# Explanation:NO restriction for the call duration of Ext.abc. Code:56 abc 1# Explanation:The call duration of Ext.
PABX Telephone Switching System User Manual v1.02 Item 21.To set system restrict number Code:71 n ABCDE# Explanation:n is the group number for the restrict numbers. There are 10 groups for restrict numbers, n is from 0-9 that matches your planning. ABCDE is five digits for restricting numbers. When less than five digits, please use * to make every group of restricted numbers five digits. For example, the first group of restricted numbers is 168. The eighth group of restrict numbers is 17909.
PABX Telephone Switching System User Manual v1.02 then dial 995*5*# Explanation: RESET -- Restore the system to default settings. Item 26. To restore the system to default setting by hardware Explanation: FOR TECHNICIANS ONLY— When the software reset does not work: To restore the system to default settings if the software setting above does not work, please disconnect the power cord and remove the top case. Restore Power being careful not to touch exposed parts and press K1 micro switch on the PCB board.
PABX Telephone Switching System User Manual v1.02 Operating Instructions: Explanation: When the extension is in the mode of getting CO line directly “you are hearing outside dial tone”, please dial * before the code. When the extension is in the mode of getting the CO line by dialing 9 first (default - you are hearing higher pitched intercom dial tone), dial the code directly without the *. Item 1.
PABX Telephone Switching System User Manual v1.02 directly. Explanation: If the caller dials 0 or a wrong extension number, Ext.600 will ring. If the dialed extension is busy and it is not set for busy transfer, the system will hint the extension is busy, or automatically transfer to Ext.600. If Ext.600 is busy, you need to set busy transfer to another extension as a second console. Item 6. Transferring the CO line call Operation: 1. Extension is talking with CO line caller. 2.
PABX Telephone Switching System User Manual v1.02 Item 9.Call parking – Hold The CO Call Operation: Extension is talking with CO line. Press R button or * and then dial #98 then hang up. The CO line is parked (on hold) and the CO caller is hearing music. To get back the parked CO line, pick up the handset, hear intercom dialing tone and dial *+#94. Explanation: After the CO line is parked, the CO line caller will hear music. It won’t effect other operations on the extension .
PABX Telephone Switching System User Manual v1.02 Item 13. To transfer the call to your new extension automatically Operation: 1. Pick up the handset and hear dialing tone, dial *#3 and the new extension number which you want to transfer. 2.To cancel this function, you just need to go back to your extension and pick up the handset and then hang up. Explanation: Some times you need to leave your extension and move to another office, and you don’t need to tell the operator you have left your extension.
PABX Telephone Switching System User Manual v1.02 Operation: 1.Pick up the handset and hear dial tone, 2.Dial * + #97 then it is the extension number. Item 17.Many CO.lines Conference When you want to make many CO.lines and extensions for conference,please dial all CO.lines first,then hold them,and after all CO.lines were holded,then dial * # 93 ,you can make conference. When one CO.line want to secede the conference,pick up other extension dial * # and (01-08) correspond CO.line code.
PABX Telephone Switching System User Manual v1.02 INDEX OF PBX SYSTEM PROGRAMMING Explanation： ： 1. All the settings should be enter the system programming state ,#99 ABCD # (ABCD means system programming password, the default password is 0000 ) on Ext.600 or Ext.607. 2. m stands for CO line code(01-08,**),when m =**, it stands for all CO.lines;abc stands for extension number, three digits. When abc=***, it stands for all extensions.
PABX Telephone Switching System User Manual v1.02 with fast-dialing number To set call extension duration of To permit extension dialing out with IP-number Clear extension password Flexible coding Change system password To set system restrict number To set system specific number To set system fast-dialing number To set system IP-number To set system long time recording Item RESET-To restore the system default setting by software To set extension number digits To set system connect OGM time To set CO.
