Installation Manuel

ManualsBrandsMajestic ManualsFireplace/Gas Stove AccessoriesPVI-SLP-B Power Vent Inline System (Wire Harness Required to Complete)

Hearth & Home Technologies • Power Vent Inline (PVI-SLP) Instructions • 2196-900 Rev. AC • 12/15

Table 2.1

WARNING! Risk of Fire!

• PVI-SLP cannot be installed directly on appliance. The PVI-SLP and combustible materials surrounding vent pipe may

overheat.

• A minimum length run of initial vent pipe is required between the appliance and the inlet of the PVI-SLP. The initial

minimum vent run requirement varies depending on the speciﬁ c appliance and its venting conﬁ guration.

• Some models require DVP Series pipe for the initial minimum vent section directly off the appliance.

MODEL MINIMUM VENTING BETWEEN APPLIANCE AND PVI-SLP

6000C, 6000CL, 6000CLX,

8000C, 8000CL, 8000CLX 6000BEC

PVI installed horizontal orientation: One 90 degree elbow and

a total of two feet of straight horizontal or straight vertical SLP

pipe. See Figure 2.2 and Figure 2.5.

PVI installed vertical orientation: Two 90 degree elbows and

a total of two feet straight horizontal or straight vertical SLP pipe.

See Figure 2.3, 2.4, 2.6.

6000CMOD, 8000CMOD

CD4236, CD4842

CNXT4236, CNXT4842

CRAVE4836, CRAVE4836ST, CRAVE6048, CRAVE6048ST

CRAVE7260, CRAVE7260ST, CRAVE8472, CRAVE8472ST

DV3732SBI

GDST3831, GDST4336, GDFL4136, GDCR4136,

GDCL4136

MEZZO36, MEZZO36ST, MEZZO48, MEZZO48ST

MEZZO60, MEZZO60ST, MEZZO72, MEZZO72ST

NDV3630, NDV3933, NDV4236, NDV4842

NEVO3630, NEVO4236

ST-36TR. ST-36TR, ST-36TRB, PIERI-36TR, PIER-36TRB,

LCOR-36TRB, RCOR-36TRB

RED40, RED40ST

REVO-S21, REVO-H31

SLR32, RAVE3012I

SLR-B, SLR-C,

RAVE 4013I, RAVE4013I-C

SL-350TRS, SL-550TRS, SL-750STRS

SL-550TR, SL-750TR, SL-950TR

SL-550METRO, SL-550-BE-M

ST-550T, ST-550TM

MODEL MINIMUM VENTING BETWEEN APPLIANCE AND PVI-SLP

ESC-42ST

PVI installed horizontal orientation: Minimum two feet straight

vertical DVP pipe directly off appliance followed by 90 degree

elbow and two feet DVP pipe. PVI-SLP adapter must be located

directly between initial DVP pipe and PVI-SLP. See Figure 2.2

and Figure 2.5.

PVI installed vertical orientation: Minimum two feet straight

vertical DVP pipe directly off appliance, followed by two 90

degree elbows and a total of two feet straight horizontal or

straight vertical DVP pipe. PVI-SLP adapter must be located

directly between initial DVP pipe and PVI-SLP. See Figure 2.3,

Figure 2.4, Figure 2.6.

ESCAPE-36DV, ESCAPE42DV

HEIR36, HEIR42, HEIR50

LUX36, LUX42

TRUE-36, TRUE-42, TRUE-50

CERONA-36, CERONA-42

PRIMO48, PRIMO48ST, PRIMO60, PRIMO60ST,

PRIMO72, PRIMO72ST

PVI installed vertical or horizontal orientation: Minimum three

feet of DVP or SLP pipe is required before connecting the PVI-

SLP system. The 3 foot minimum does not include the factory-

installed six inch DVP pipe.

B. Vent/Pipe Regulations (continued)