Electric Fireplace Model HE32EF Installation Instructions & Homeowner's Manual WARNING! IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED EXACTLY, AN ELECTRICAL SHOCK OR FIRE MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. FOR YOUR SAFETY C US DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPOURS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. The Vermont Castings Majestic Products Company ™ 410 Admiral Blvd. • Mississauga, Ontario • Canada L5T 2N6 www.
TABLE OF CONTENTS Please read the Installation & Operating Instructions before using this appliance. Thank you and congratulations on your purchase of a Vermont Castings Majestic Products Company fireplace. IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible electric shock, fire hazard and/or injury and will void the warranty. Installation Instructions ............................................................
INSTALLATION INSTRUCTIONS GENERAL 1 . Read all instructions before using this appliance. 15. To prevent a possible fire, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a bed, where openings may become blocked. 2. This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. If provided, use handles when moving this appliance.
FIREPLACE DIMENSIONS B F D A E G H C MINIMUM FIREPLACE OPENING T U S Q R R - Fireplace opening width Q - Fireplace opening height S - Firebox width at depth(T) T - Firebox depth at back height (U) U - Height at depth HE32EF T R I M F I R E P L A C E M I N I M U M O P E N I N G A1 265/8" B1 A2 B2 A3 B3 A4 B4 A5 B5 C D E F G H Q R S T U 3/8" 38 29" 4115/16" 33" 44" 28" 407/8" 301/2" 46" 283/4" 183/4" 111/2" 13" 22" 20" 21" 28" 19" 113/4" 201/4" 676 mm 975 737 1065 838 1118 712 1041 775 1171
MANTELS FRAMING & FINISHING When the fireplace is being installed into a woodburning fireplace the minimum the mantel can be above the fireplace is governed by local building codes applicable to woodburning fireplaces. Consult local authorities having jurisdiction for these clearances. Before deciding on the frame dimensions and finishing materials it is important to consider the finished dimensions of the chosen fireplace trim kit (see options section of this manual).
INSTALLATION OF LOGS ELECTRICAL CONNECTION 1. Turn off power to the unit. A 15 AMP, 120 Volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow when the heater is in operation. The unit comes standard with a 6 ft. (1828mm) long three wire cord, exiting the right side of the fireplace.
SERVICE INSTRUCTIONS Disconnect power before attempting any maintenance or cleaning to reduce the risk of fire, electrical shock or personal injury. GLASS INFORMATION 1. Under no circumstances should this product be operated with missing or broken glass. 2. Do not strike or slam the glass. 3. Do not use abrasive cleaners to clean the glass. 4. This product uses tempered glass. Replacement of the glass with gasket as supplied by the manufacturer should be done by a qualified service person.
MAINTENANCE OF MOTORS CLEANING BRASS TRIM The motors used on the fan and the drum assembly are prelubricated for extended bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the fan/heater is recommended. Clean the brass trim using a soft cloth, slightly dampened with lemon oil and buff with a clean soft cloth. Do NOT use brass polish or household cleaners as these products will damage the brass trim. Lemon oil can be obtained at supermarkets or hardware stores.
OPERATING INSTRUCTIONS The control compartment is located behind the lower louvre panel. To access the controls, simply flip down the lower louvre panel. To locate the position of each control described below, refer to Fig. 7. 2. HEATER CONTROL The Heater Control acts to turn the heater on and off as well as setting the comfort level in the room. Turning the knob clockwise from the off position will place the heater into operation.
REPLACEMENT PARTS - ELECTRIC FIREPLACE 18 8 15 7 4/5 9 6 13 14 20 2 21 23 216mm [8 1/2"] (DISTANCE BETWEEN TWO SOCKETS) 216mm [8 1/2"] (DISTANCE BETWEEN TWO SOCKETS} 305mm [12"] #1 COMPLETE LOG SET 19 22 3 17 HE32EF #2 COMPLETE LOG SET - 10 -
REPLACEMENT PARTS LIST - ELECTRIC FIREPLACE DESCRIPTION 1. 1a. 1b. 1c. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. 23.
FAN HEATER INSTALLATION INSTALLATION WARNING: UNPLUG OR TURN THE POWER TO THE APPLIANCE OFF PRIOR TO BEGINNING THE INSTALLATION. IT IS NOT ACCEPTABLE TO USE THE “ON/OFF” SWITCH TO MEET THIS REQUIREMENT. 1. 2. 3. 4. 5. Turn the power to the appliance off, or unplug it from the power supply. Let fireplace cool if it has been operating. Remove access panel radiance by lifting up and pulling out or open lower louvre assembly. Remove two door retention screws along lower sides edge of door frame.
TRIM OPTIONS FOR HE32EF 1) RHESS, RHESL, RHESSD, RHESLD & RHESXL TRIMS FRAME ASSEMBLY RHESS, RHESL, RHESSD, RHESLD and RHESXL 1. Lay Trim Top Facing and Trim Side Facings, face down on to an even surface such as a table or floor. Be sure not to scratch the painted surfaces. 2. Install the nuts and bolts (Fig. 8). Trim Top Deflector Trim Frame Top Section Side View 10/24 SCREWS RHESSD and RHESLD (Fig. 11) FRAME TOP LEFT FRAME Fig. 10 1. Install trim channels (left and right sides).
FRAME MOUNTING GENERAL INFORMATION The Decorative Front Frame should be installed last after all other work, has been completed and thoroughly checked and tested for operation and proper installation requirements. 1. Fit Decorative Frame to the fireplace and fasten (Fig. 12) SCREWS AS SHOWN FROM FRONT Fig. 12 Plastic on the trim must be removed before mounting onto the fireplace. Glass must be tightly pressed against the front of the frame in order to prevent screws from damaging glass edges.
TRIM REPLACEMENT PARTS LIST ALL repair parts will be available from your local dealer.
2) RHEBSL & RHEBXL TRIMS RHEBXL TRIM ASSEMBLY To install the kit you do not have to remove any piece of brass, you just add the external pieces. RHEBSL 1. Install trim channels (left and right sides). Use two screws to assemble each piece. 2. Slide on the trim top channel and fasten it from the back side. 3. Install the trim top deflector and use two screws to fasten it. (Fig. 13) 4. Remove ALL plastic protective covering from brass trim. Remove the frame trim from the unit if it is already installed.
3) RHEFA and RHEFP TRIMS TRIM ASSEMBLY 3. Install bottom decorative plate by simply sliding it under the unit floor. No fastening is required for this installation (See Fig. 16). Be sure to remove protective cover. 4. Install the bottom louvre assembly by fastening the hinges with four screws to the pre-punched holes in the cabinet. 5. Re-install the front glass. 6. Install the top louvre by using the hooks to hang it in place. 1. Remove the front glass (see "Glass Frame Removal" section). 2.
4) HEBTKP, HESBTKP, HECBTK, HECBTKMB & HEBTA TRIMS HECBTK HECBKMB HESBTKP HEBTKP - Cast bay window and grills in classic black trim kit Cast bay window and grills in midnight black porcelain enamel trim kit Steel bay window with polished brass and cast grills in classic black trim kit Steel bay window and bay louvres with polished brass trim kit Install the bay window after all other installation work has been completed, thoroughly checked, and tested for operation, leaks and proper installation requirem
HEBTKP Trim Assembly 1) 2) 3) 4) 5) 6) Install the hanging brackets, as per Fig. 20 Install bracket on each side of the cabinet as per Fig. 24. Install the two ceramic pieces inside the bay window, as per Fig. 19. Install the bay window by hanging it onto the lower tabs of the hanging brackets, as per Fig. 21. Install top louvre by engaging the obround holes with the upper tabs of the hanging brackets, as per Fig. 22. Install brass trim to the steel frame as per Fig. 23. Fig.
TRIM REPLACEMENT PARTS LIST ALL repair parts will be available from your local dealer.
5) CAST TRIM OPTIONS CAST SURROUND AND FLAT FACE HECBL HECBLUE HECCG HECGR Cast Surround Black Cast Surround Blue Cast Surround Charcoal Grey Cast Surround Green CSSP CSLP Polished Brass Small Trim for Cast Surround Polished Brass Large Trim for Cast Surround (to be used with CSSP) ACCESSORIES OPTIONS DESCRIPTION • • • • • Remote Control Optional Heater Cabinet / Mantel Ceramic Refractory Kit Bay Window - 21 -
