User Manual
Page 8
Connecting at Engine
L
O
W
E
R
R
A
D
I
A
T
O
R
&
O
V
E
R
F
L
O
W
O
F
F
E
M
P
T
Y
W
A
S
T
E
T
A
N
K
&
O
V
E
R
F
L
O
W
L
O
W
E
R
R
A
D
I
A
T
O
R
E
M
P
T
Y
W
A
S
T
E
T
A
N
K
E
X
C
H
A
N
G
E
C
O
O
L
A
N
T
&
O
V
E
R
F
L
O
W
F
I
L
L
R
A
D
I
A
T
O
R
S
Y
S
T
E
M
P
R
E
S
S
U
R
E
T
E
S
T
O
F
F
O
F
F
F
I
L
L
R
A
D
I
A
T
O
R
&
O
V
E
R
F
L
O
W
E
X
C
H
A
N
G
E
C
O
O
L
A
N
T
O
R
S
Y
S
T
E
M
V
A
C
U
U
M
Hose
Radiator
Green Hose
Black Hose
E
M
P
T
Y
W
A
S
T
E
T
A
N
K
F
I
L
L
R
A
D
I
A
T
O
R
&
O
V
E
R
F
L
O
W
E
X
C
H
A
N
G
E
C
O
O
L
A
N
T
O
R
L
O
W
E
R
R
A
D
I
A
T
O
R
&
O
V
E
R
F
L
O
W
&
O
V
E
R
F
L
O
W
L
O
W
E
R
R
A
D
I
A
T
O
R
E
M
P
T
Y
W
A
S
T
E
T
A
N
K
E
X
C
H
A
N
G
E
C
O
O
L
A
N
T
&
O
V
E
R
F
L
O
W
F
I
L
L
R
A
D
I
A
T
O
R
S
Y
S
T
E
M
P
R
E
S
S
U
R
E
S
Y
S
T
E
M
V
A
C
U
U
M
T
E
S
T
O
F
F
O
F
F
O
F
F
Adapter
Block
Engine
Hose
Radiator
Overflow
Adapters
Step
Pump
Water
Green Hose
Connecting at Radiator
Radiator
Overflow
Hose
Radiator
Adapter
Hose
Step
Adapters
Black Hose
Core
Heater
Pump
Water
Block
Engine
Core
Heater
CONNECTING TO THE COOLANT SYSTEM
The MCX-2F can be connected to the cooling system in either of the configurations
shown below. The choice is dependent on the ease of accessability to the hose
connections.
1. Turn both valves on the front of the MCX-2F to EXCHANGE.
2. Disconnect the radiator hose from either the engine or the radiator.
3. Select an Adapter Hose with the same inner diameter as the radiator hose and
connect at the point the radiator hose was disconnected using a clamp.
4. Install Step Adapters in the Adapter Hose and the radiator hose using clamps.
Make sure the outside diameter of the Step Adapters is the same as the inner
diameter of the radiator hose.
5. Connect the Green and Black hoses from the MCX-2F to the two Step
Adapters as shown in the illustrations. See next page for special hookups.
6. Open the valves on the two Step Adapters.