Manual

Page 8
Water
Pump
Connecting at Engine
O
F
F
O
F
F
O
F
F
T
E
S
T
S
Y
S
T
E
M
V
A
C
U
U
M
S
Y
S
T
E
M
P
R
E
S
S
U
R
E
F
I
L
L
R
A
D
I
A
T
O
R
&
O
V
E
R
F
L
O
W
E
X
C
H
A
N
G
E
C
O
O
L
A
N
T
E
M
P
T
Y
W
A
S
T
E
T
A
N
K
L
O
W
E
R
R
A
D
I
A
T
O
R
&
O
V
E
R
F
L
O
W
&
O
V
E
R
F
L
O
W
L
O
W
E
R
R
A
D
I
A
T
O
R
E
X
C
H
A
N
G
E
C
O
O
L
A
N
T
O
R
F
I
L
L
R
A
D
I
A
T
O
R
&
O
V
E
R
F
L
O
W
E
M
P
T
Y
W
A
S
T
E
T
A
N
K
Black Hose
Green Hose
Radiator
Hose
Step
Adapters
Overflow
Radiator
Connecting at Radiator
Engine
Block
Green Hose
Black Hose
S
Y
S
T
E
M
V
A
C
U
U
M
E
X
C
H
A
N
G
E
C
O
O
L
A
N
T
O
R
F
I
L
L
R
A
D
I
A
T
O
R
&
O
V
E
R
F
L
O
W
O
F
F
O
F
F
T
E
S
T
S
Y
S
T
E
M
P
R
E
S
S
U
R
E
F
I
L
L
R
A
D
I
A
T
O
R
&
O
V
E
R
F
L
O
W
E
X
C
H
A
N
G
E
C
O
O
L
A
N
T
E
M
P
T
Y
W
A
S
T
E
T
A
N
K
L
O
W
E
R
R
A
D
I
A
T
O
R
&
O
V
E
R
F
L
O
W
E
M
P
T
Y
W
A
S
T
E
T
A
N
K
O
F
F
&
O
V
E
R
F
L
O
W
L
O
W
E
R
R
A
D
I
A
T
O
R
Hose
Engine
Block
Adapter
Heater
Core
Hose
Adapters
Step
Hose
Adapter
Radiator
Water
Pump
Overflow
Radiator
Heater
Core
CONNECTING TO THE COOLANT SYSTEM
The MCX-2F can be connected to the cooling system in either of the configurations
shown below. The choice is dependent on the ease of accessability to the hose
connections.
1. Turn both valves on the front of the MCX-2F to EXCHANGE.
2. Disconnect the radiator hose from either the engine or the radiator.
3. Select an Adapter Hose with the same inner diameter as the radiator hose and
connect at the point the radiator hose was disconnected using a clamp.
4. Install Step Adapters in the Adapter Hose and the radiator hose using clamps.
Make sure the outside diameter of the Step Adapters is the same as the inner
diameter of the radiator hose.
5. Connect the Green and Black hoses from the MCX-2F to the two Step Adapters
as shown in the illustrations. See next page for special hookups.
6. Open the valves on the two Step Adapters.