OPERATION MANUAL MCX-2S Multiple Coolant Exchanger SYS TEM PRE SSU RE SYS TEM VAC UU M LOW & OVER RAD ER FLO IATOR W EM PTY LOW & OVER RAD ERF IAT LOW OR WA STE TES OF F FIL EXCHA L RAD T NG IAT E CO OR OLA & OVE NT RFL OR OW TAN K EXC HA NG E CO OLA FIL & OVL RA ER DIATOR FLO W OF F NT EM PTY WA STE TAN K OFF RTI Technologies, Inc. 4075 East Market St. York, PA 17402 USA 800-468-2321 www.rtitech.
TABLE OF CONTENTS Component Description . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Operation of Valves . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Relieving Radiator Pressure . . . . . . . . . . . . . . . . . . . . 5 Lowering Coolant Level . . . . . . . . . . . . . . . . . . . . . . . 6 Connecting to the Coolant System . . . . . . . . .
COMPONENT DESCRIPTION Unpack all components and verify quantities per this illustration. Contact RTI if any items are missing or damaged.
SAFETY PRECAUTIONS WARNING: FAILURE TO FOLLOW THESE PRECAUTIONS CAN RESULT IN SERIOUS INJURY OR DEATH. C Read and understand the Operation Manual completely before operating this unit. C Always wear proper eye and skin protection when operating and maintaining this equipment. C Take precautions to keep clothing, hair, hands, hoses, etc. away from all moving parts on the vehicle. C Automotive cooling systems can be under pressure and extremely hot. Use extreme caution when removing caps and hoses.
SET UP The MCX-2S was carefully packaged by RTI to arrive without damage. Report any evidence of damage immediately by calling RTI Technical Support at 800-468-2321. Conventional Green Gold Mon. - Fri. 8AM - 5PM (Eastern Time) Sat. - Sun. 8AM - 12PM (Eastern Time) Following are the steps required to prepare the MCX-2S for operation: 1. Remove all packing materials. Press sides of buckle to release black web strap on rear of unit. Remove the tanks and the accessory cartons from their shipping position.
RELIEVING RADIATOR PRESSURE WARNING: Coolant in the vehicle cooling system may be extremely hot and under great pressure. Wear safety glasses and use protective clothing and gloves. Use extreme caution when removing radiator cap and hoses.
LOWERING COOLANT LEVEL Green Hose Black Hose SYST EM PRE SSU RE SYS TEM VAC UUM LOW ER & OVE RAD RFLO IATO W R EMP TY LOW & ER RAD OVE RFLO IATO W R WAS TE OFF TEST FILLEXC HAN RAD GE IATO COO R& LANT OVE RFLOOR TAN K W EXC HAN GE FILL & OVERAD IATO RFLO R W COO LAN OFF T EMP TY Radiator Hose W ASTE TAN K OFF Engine Block Wand Heater Core Water Pump Radiator Overflow SY ST EM PR ES SU RE SYS TE M VAC UU M LO W & O ER R VE AD RFL IATO OW R LO EM PTY W & O ER R VER AD FL IATO
CONNECTING TO THE COOLANT SYSTEM The MCX-2S can be connected to the cooling system in either of the configurations shown below. The choice is dependent on the ease of accessability to the hose connections. 1. Disconnect the radiator hose from either the engine or the radiator. 2. Select an Adapter Hose with the same inner diameter as the radiator hose and connect at the point the radiator hose was disconnected using a clamp. 3.
SPECIAL HOOKUPS Special Hookup 1) It may be necessary to reverse the hoses during the coolant replacement procedure on the following pages for systems with a reverse-connected thermostat. See note after Step 7 for the symptoms of this situation. Special Hookup 2) Some cooling systems do not have a cap on the radiator. Instead, there is a single cap on the overflow tank as shown in the illustration below.
COOLANT REPLACEMENT Once the MCX-2S is connected as described on the preceding pages it is ready to replace the old coolant with new coolant.
COOLANT REPLACEMENT QUARTS 8 Quarts 30 28 26 24 22 20 18 16 14 12 10 8 6 4 2 LITERS 28 26 24 22 20 18 16 14 12 10 8 6 4 2 4. Set one of the Level Magnets at the fluid level in the New Coolant Tank (24 in above drawing). Determine the amount of coolant to be exchanged (8 Quarts for example) and position the other Level Magnet that many quarts below the other magnet (16 in above drawing). 5. Turn control valve to EXCHANGE COOLANT. 6.
TEST COOLANT SYSTEM FOR LEAKS The MCX-2S can be used to check the coolant system for leaks. The coolant system is pressurized and the System Pressure Gauge on the MCX-2S is monitored for a drop in pressure which would indicate a system leak.
COMPLETING THE JOB All used coolant in the vehicle cooling system has now been replaced with new coolant. The following steps will complete the job.
COMPLETING THE JOB Green Hose Black Hose SYS TEM PRE SSU RE SYS TEM VAC UUM LOW & ER RAD OVE RFL IAT OW OR EM PTY LOW & OVER RAD ERF IAT LOW OR WA STE OFF TES T FIL EXC L RADHAN GE IAT OR COO & LAN OVE T RFL OR OW TAN K EXC HAN GE & FIL L RA OVE DIA RFL TOR OW CO OLA OFF NT EM PTY WA STE Radiator Hose TAN K OFF Engine Block Wand Heater Core Water Pump Radiator Overflow SY ST EM PR ES SU RE SY ST EM VA CU UM LO W & O ER R VE AD RF IAT LO OR W EM PT Y LO W & O ER R VE AD RF IAT
CHANGING COOLANT TYPE The MCX-2S has a means for easily using different types of coolants. A special feature is the clearing process which purges coolant from the hoses and pumps prior to changing the new coolant tank. The MCX-2S must be connected to a battery during this procedure.
CHANGING COOLANT TYPE Green Hose Black Hose SYS TEM PRE SSU RE SY STE M VAC UUM SY ST EM LOW & OVER RA ERF DIA LOW TOR EM PTY LOW & OVER RAD ER FLO IATOR W WA STE TAN OFF TES T FIL EXC L RADHAN GE IAT OR CO OL & OV ANT ERF OR LOW K PR ES SU RE EXC HA NG E CO OLA FIL NT L RA & OVE DIA RFL TOR OW OFF EM PTY SY ST EM WA STE TAN K OF F VA CU UM Green Hose LO W & O ER R VE AD RF IAT L O OR W LO Wand EM PT Y W & O ER R VE AD RF IAT LO OR W WA ST ET OF F FIL EXC L R HA AD NG IAT E
EMPTYING THE WASTE TANK The Waste Tank can be emptied two different ways. A. The Waste Tank can be removed from the MCX-2S and transported to the area where it is to be emptied. A quick connect coupler is installed on the black hose to make this disconnection quick and clean. B. The MCX-2S can be used to pump the waste coolant directly from the Waste Tank into another waste collection tank. A 12 volt battery will be required to power the MCX-2S.
REPLACEMENT PARTS - POWS Numbers Visit our web-site at www.rtitech.
WASTE PUMP IMPELLER REPLACEMENT The waste pump impeller may require periodic replacement. The concentration of impurities in recovered old coolant affects the life of the pump impeller. Changing the impeller is quick and easy as follows: 1. Remove Hose Holder on rear of unit to access the end of the Waste Pump. 2. Remove 3 screws. 3. Remove cover plate, gasket and worn impeller. 4. Coat new impeller with Vaseline® petroleum jelly. 5. Align flats and press impeller onto shaft. 6.
FLOW & WIRING DIAGRAM Page 19