OPERATION MANUAL MCX-2 Multiple Coolant Exchanger SYS TEM PRE SSU RE SYS TEM V ACU UM LOW & ER OVE R ADIA RFL OW TOR LOW EMP TY ER & OVE RAD R FLO I ATO W R W OFF TES T FILLEX CHA R ADI N GE ATO COO R& LAN OVE T RFL OR OW AST E TAN K E XCH AN GE FILL & OVERAD R FLOIATO R W COO OFF LAN T EMP TY W AST E TAN K OFF 4075 East Market Street York, Pennsylvania USA 800-468-2321 www.rtitech.
TABLE OF CONTENTS Component Description . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Set-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Connection to Power . . . . . . . . . . . . . . . . . . . . . . . . . 5 Relieving Radiator Pressure . . . . . . . . . . . . . . . . . . . 6 Lowering Coolant Level . . . . . . . . . . . . . . . . . . . . . . . 7 Connecting to the Coolant System . . . . . . . . . . . . .
COMPONENT DESCRIPTION Unpack all components and verify quantities per this illustration. Contact RTI if any items are missing or damaged.
SAFETY PRECAUTIONS WARNING: FAILURE TO FOLLOW THESE PRECAUTIONS CAN RESULT IN SERIOUS INJURY OR DEATH. C Read and understand the Operation Manual completely before operating this unit. C Always wear proper eye and skin protection when operating and maintaining this equipment. C Take precautions to keep clothing, hair, hands, hoses, etc. away from all moving parts on the vehicle. C Automotive cooling systems can be under pressure and extremely hot.
SET UP Install Filter and Bowl on rear of MCX-2 as shown. These items are shipped in the carton with the adapters and adapter hoses. The MCX-2 has two tanks (plus an extra New Coolant Tank) which are installed and connected from the rear. Quick connect couplers are mounted on the hoses which connect these tanks to the MCX-2. A green hose connects to the small New Coolant Tank and a black hose connects to the large Waste Tank.
CONNECTION TO POWER SY ST EM PR ES SU RE SY ST E M VA C UU M LO W & O ER R VE AD RF IAT LO O W R EM PT LO W & O ER R VE AD RF IAT LO O W R YW AS TE TA OF F FIL EXC L R HA AD N G IA E C TO OO R & O LAN VE T O RF R LO W TE ST NK EX CH AN G FIL & L RA OV ER DIAT FL O R OW EC OF OO LA NT EM PT OF Y WA ST ET F AN K F The MCX-2 control panel is illustrated above. Note that the bottom of all three selector switches has been pressed which turns all functions off.
RELIEVING RADIATOR PRESSURE WARNING: Coolant in the vehicle cooling system may be extremely hot and under great pressure. Wear safety glasses and use protective clothing and gloves. Use extreme caution when removing radiator cap and hoses.
LOWERING COOLANT LEVEL Green Hose Black Hose SYS TE M PR ESS U RE SYS TEM VAC U UM LOW & ER OVE R ADI RFL ATO OW R LOW ER & OVE RAD RFL E MP IATO OW R TY WAS TE OFF TES T FI LL TAN EXC HAN R ADI GE ATO R K EXC HAN GE FILL & OVERAD R FLOIATO R W COO OFF LAN T EMP TY COO LAN & OV T ERF OR LOW Radiator Hose WA STE TAN K OFF Engine Block Wand Heater Core Water Pump Radiator Overflow SY ST E M PR ES SU RE SY ST E M VA CU UM LO W & O ER R VE AD RF IAT LO O R W EM P LO W & O
CONNECTING TO THE COOLANT SYSTEM The MCX-2 can be connected to the cooling system in either of the configurations shown below. The choice is dependent on the ease of accessability to the hose connections. 1. Disconnect the radiator hose from either the engine or the radiator. 2. Select an Adapter Hose with the same inner diameter as the radiator hose and connect at the point the radiator hose was disconnected using a clamp. 3.
SPECIAL HOOKUPS Special Hookup 1) It may be necessary to reverse the hoses during the coolant replacement procedure on the next page for systems with a reverse-connected thermostat. See note after Step 6 on next page for the symptoms of this situation. Special Hookup 2) Some cooling systems do not have a cap on the radiator. Instead, there is a single cap on the overflow tank as shown in the illustration below.
COOLANT REPLACEMENT Once the MCX-2 is connected as described on the preceding pages it is ready to Green Hose replace the old coolant with new coolant.
TEST COOLANT SYSTEM FOR LEAKS The MCX-2 can be used to check the coolant system for leaks. The coolant system is pressurized and the System Pressure Gauge on the MCX-2 is monitored for a drop in pressure which would indicate a system leak.
COMPLETING THE JOB All used coolant in the vehicle cooling system has now been replaced with new coolant. The following steps will complete the job.
COMPLETING THE JOB Green Hose Black Hose S YS TEM PRE SS URE S YS TEM VAC UUM LOW & ER OV RAD ERF IA LOW TOR LOW & ER OVE RA RFL DIA TOR OW EMP TY OFF TES FILLE XCH RA A NGE DIA TOR COO & OV LA NT E RFL OR OW T WA S TE TAN K E XCH A NGE FILL & OV RA DIAT ERF LOWOR COO LA OFF NT EMP TY WA Radiator Hose STE TAN K OFF Engine Block Wand Heater Core Water Pump Radiator Overflow SY ST EM PR ES SU RE SY ST EM VA CU UM LO W & ER R OV ER ADIA FL T OW OR LO W & O ER R VE AD RF IAT LO
CHANGING COOLANT TYPE The MCX-2 has a means for easily using different types of coolants. A special feature is the clearing process which purges coolant from the hoses and pumps prior to changing the new coolant tank. The MCX-2 must be connected to a battery during this procedure.
CHANGING COOLANT TYPE Green Hose Black Hose SYS TE M PR ESS UR E SY STE M VAC UUM SY ST EM LO WE R & OVE RA DIA R FLO TO W R EM LO WE & OV R RA ERF DIA LOW TOR PTY WA OF F TES FILLEXCHA RA NG DIA E TO CO R & OLA OV NT ER OR FLO W T STE TA NK EXC HA NG FIL & OVL RA ER DIA TO FLO R W E CO OLA PR ES SU RE OF F NT EM SY ST EM PTY WA STE TAN K OFF VA CU UM Green Hose LO W & ER OV RA ER DIA FL T OW OR Wand LO W & O ER R VE AD RF IAT LO OR EM W PT YW AS TE TA NK OF F TE ST FIL E
EMPTYING THE WASTE TANK The Waste Tank can be emptied two different ways. A. The Waste Tank can be removed from the MCX-2 and transported to the area where it is to be emptied. A quick connect coupler is installed on the black hose to make this disconnection quick and clean. B. The MCX-2 can be used to pump the waste coolant directly from the Waste Tank into another waste collection tank. A 12 volt battery will be required to power the MCX-2.
REPLACEMENT PARTS Call 800-468-2321 (Extension 259) For Technical Support or Parts Ordering Visit our web-site at www.rtitech.
WASTE PUMP IMPELLER REPLACEMENT The waste pump impeller may require periodic replacement. The concentration of impurities in recovered old coolant affects the life of the pump impeller. Changing the impeller is quick and easy as follows: 1. Remove Hose Holder on rear of unit to access the end of the Waste Pump. 2. Remove 4 screws. 3. Remove cover plate, gasket and worn impeller. 4. Coat new impeller with Vaseline® petroleum jelly. 5. Align flats and press impeller onto shaft. 6.
FLOW & WIRING DIAGRAM Page 19