Programmer's99875629 Owner's manual
Table Of Contents
- Table of Contents
- 1 Introduction
- 2 Connection Types
- 3 Command Set
- 3.1 About Big Block Data Mode
- 3.2 About SRED / Non-SRED Firmware
- 3.3 About Commands Tagged As “MAC”
- 3.4 General Feature Reports
- 3.4.1 Report 0x01 – Response ACK
- 3.4.2 Report 0x02 – End Session
- 3.4.3 Report 0x03 – Request Swipe Card
- 3.4.4 Report 0x04 – Request PIN Entry
- 3.4.5 Report 0x05 – Cancel Command
- 3.4.6 Report 0x06 – Request User Selection
- 3.4.7 Report 0x07 – Display Message
- 3.4.8 Report 0x08 – Request Device Status
- 3.4.9 Report 0x09 – Set Device Configuration
- 3.4.10 Report 0x09 – Get Device Configuration
- 3.4.11 Report 0x0A – Request MSR Data
- 3.4.12 Report 0x0B – Get Challenge
- 3.4.13 Report 0x0D – Send Session Data - Amount
- 3.4.14 Report 0x0D – Send Session Data - PAN
- 3.4.15 Report 0x0E – Get Information
- 3.4.16 Report 0x0F – Login/Authenticate
- 3.4.17 Report 0x0F – Logout
- 3.4.18 Report 0x10 – Send Big Block Data to Device
- 3.4.19 Report 0x11 – Request Manual Card Entry
- 3.4.20 Report 0x14 – Request User Data Entry
- 3.4.21 Report 0x1A – Request Device Information
- 3.4.22 Report 0x1C – Set/Get BLE Power Configuration (BLE Only)
- 3.4.23 Report 0x1D – Set BLE Module Control Data (BLE Only)
- 3.4.24 Report 0x1E – Set iAP Protocol Info (30-pin Only)
- 3.4.25 Report 0x1E – Get iAP Protocol Info (30-pin Only)
- 3.4.26 Report 0x1F – Request Clear Text User Data Entry
- 3.4.27 Report 0x30 – Set / Get KSN
- 3.4.28 Report 0x31 – Set KSN Encrypted Data
- 3.4.29 Report 0x32 – Set BIN Table Data (MAC)
- 3.4.30 Report 0x32 – Get BIN Table Data
- 3.4.31 Report 0xFF – Device Reset
- 3.5 General Input Reports
- 3.5.1 Report 0x20 – Device State Report
- 3.5.2 Report 0x21 – User Data Entry Response Report
- 3.5.3 Report 0x22 – Card Status Report
- 3.5.4 Report 0x23 – Card Data Report
- 3.5.5 Report 0x24 – PIN Response Report
- 3.5.6 Report 0x25 – User Selection Response Report
- 3.5.7 Report 0x27 – Display Message Done Report
- 3.5.8 Report 0x29 – Send Big Block Data to Host
- 3.5.9 Report 0x2A – Delayed Response ACK
- 3.5.10 Report 0x2B – Test Response
- 3.5.11 Report 0x2D –BLE Module Control Data (BLE Only)
- 3.5.12 Report 0x2E – Clear Text User Data Entry Response Report
- 3.6 EMV-Related Reports
- 3.6.1 Report 0x2C – EMV Cardholder Interaction Status Report
- 3.6.2 Report 0xA1 – Set or Get EMV Tag(s) (MAC)
- 3.6.3 Report 0xA2 – Request Start EMV Transaction
- 3.6.4 Report 0xA4 – Acquirer Response (MAC)
- 3.6.5 Report 0xA5 – Set or Get CA Public Key (MAC)
- 3.6.6 Report 0xA8 – Get Kernel Info
- 3.6.7 Report 0xAB – Request EMV Transaction Data (MAC)
- 3.6.8 Report 0xAC – Merchant Bypass PIN Command
- Appendix A Examples
- Appendix B Terminology
- Appendix C Status and Message Table
- Appendix D MagTek Custom EMV Tags
- Appendix E Configurations
- Appendix F Error Codes
- Appendix G User-Defined Messages
- Appendix H Factory Defaults
- Appendix I Language and Country Codes
- Appendix J BLE Module Control Data
- J.1 BLE Module Configuration Properties
- J.1.1 Get property command
- J.1.2 Set property command
- J.1.3 Software ID property
- J.1.4 Bluetooth Device Address property
- J.1.5 Bluetooth Device Name property
- J.1.6 Configuration Revision property
- J.1.7 Power Timeout property
- J.1.8 Power Control property
- J.1.9 Advertising Control property
- J.1.10 Passkey property
- J.1.11 Desired Minimum Connection Interval Property
- J.1.12 Desired Maximum Connection Interval Property
- J.1.13 Desired Slave Latency Property
- J.1.14 Desired Supervision Timeout Property
- J.1.15 Connection Parameter Update Request Control Property
- J.2 Other Commands
- J.1 BLE Module Configuration Properties
Appendix H - Factory Defaults
DynaPro Mini| PIN Encryption Device | Programmer’s Reference (Commands)
Page 102
Tag Description
Tag
Configurable
Default Value (hex)
Certification Validation
Table
0xDFDF07
Not supported
00
Default CVM
0xDFDF13
Acquirer
01
Socket Timeout
0xDFDF14
Acquirer
00 00 0B B8
Socket Retries
0xDFDF15
Acquirer
00 00 00 01
Issuer Script Max Size
0xDFDF16
Compile Only
00 00 00 80
Batch Data Tags
0xDFDF17
Acquirer
82 8E 5F 24 5F 25 9F 06 9F 07 9F 0D 9F
0E 9F 0F 9F 10 9F 26 9F 27 9F 36 95 9B
9C 9F 33 9F 34 9F 37 9F 40 DF DF 70 DF
DF 71 DF DF 72 9F 5B
Default Terminal
Language
0xDFDF19
Acquirer
65 6E
Terminal Features
0xDFDF20
Manufacturing
57
Acquirer Terminal
Config - Fallback
0xDFDF67
Acquirer
01
Acquirer Terminal
Config - PIN Bypass
0xDFDF68
Acquirer
01
Terminal/Payment
Brand Label
0xDFDF26
Acquirer
00 00 00 …00 [20 bytes]
Terminal/Payment
Brand Database
Checksum
0xDFDF27
Device
Calculated
CAPK Label
0xDFDF28
Acquirer
00 00 00 …00 [20 bytes]
CAPK Database
Checksum
0xDFDF29
Device
Calculated
Supported Terminal
Languages
0xDFDF2
D
Manufacturing
65 6e 66 72 69 74 64 65 65 73
H.2 Payment Brand Factory Defaults
Table 3-98 - Payment Brand Factory Defaults
Tag Description
Tag
Configurable
Default Value(hex)
Application DF Name
0x84
Acquirer
A0 00 00 00 04 10 10
TDOL
0x97
Acquirer
5F2403
Acquirer ID
0x9F01
Acquirer
00 00 00 00 00 01
Application AID
0x9F06
Acquirer
A0 00 00 00 04 10 10
Floor Limit
0x9F1B
Acquirer
00 00 27 10