User manual

ManualsBrandsMagtec ManualsDigital Video Recorders (DVR)MT854

─ 4 Channel DVR ─

User Manual

MT854

This document contains preliminary information and subject to change without notice.

Summary of content (111 pages)

PAGE 1
User Manual MT854 ─ 4 Channel DVR ─ This document contains preliminary information and subject to change without notice.
PAGE 2
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. This symbol is intended to alert the user to the presence of unprotected “Dangerous voltage" within the product's enclosure that may be strong enough to cause a risk of electric shock. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
PAGE 3
Table of Contents CHAPTER 1 PACKING DETAIL AND INSTALLATION _____________________ 6 1-1 PACKING ___________________________________________________ 6 1-2 Hard Disk Installation ________________________________________ 7 CHAPTER 2 PANEL LOCATION ________________________________________ 9 2-1 FRONT PANEL CONTROLS ___________________________________ 9 2-2 8CH REAR PANEL CONNECTORS ____________________________ 10 2-3 4CH REAR PANEL CONNECTORS ____________________________ 11 CHAPTER 3 LIVE, PLAYBACK AND PTZ OPER
PAGE 4
CHAPTER 6 Remote Software Installation and Setup ____________________ 46 6-1 AP Software Installation and instruction ______________________ 46 6-2 How to do remote monitoring through IE _____________________ 48 6-3 How to do remote monitoring through JPEG VIEWER(Only Monitor Function) _____________________________________________________ 49 6-4 AP Software Operation ______________________________________ 51 CHAPTER 7 SPECIFICAITONS _______________________________________ 52 CHAPTER 8 MOBILE APPLICATION INS
PAGE 5
9-5 Main Display _______________________________________________ 89 9-5.1 Audio Control _________________________________________ 89 9-5.2 eMAP Display _________________________________________ 90 9-5.3 PTZ Control ___________________________________________ 91 9-6 Operation Bar ______________________________________________ 92 9-6.1 User administration ____________________________________ 93 9-6.2 DVR Administration ____________________________________ 94 9-6.
PAGE 6
CHAPTER 1 PACKING DETAIL AND INSTALLATION 1-1 PACKING 1. DVR 2. Quick Start 5. CD 3. IR Remote Control 6.Screws x4 4. SATA Cord 1pcs 7. Power Adaptor Note: Standard shipping products include neither HDD nor DVD R/W MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 7
1-2 Hard Disk Installation Step１)：Take out the screws as pictures show。 Back panel 3 screws Left 1 screw Right 1 screw Step 2 ) ：Open the cover follow the arrow direction。 MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 8
Step３)：Connect SATA & Power wire to Hard Disk and put it on right position of the bottom case。 Step４)：Fix the Hard Disk with four screws on the bottom case as the picture indicated。 Step５)：Put the cover back and fix it with 5 screws as Step 1 indicated. Note: After installation, please initialize Hard Disk before starting to record. For more detailed information, please check out User Manual 4-9 System Tools for reference. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 9
CHAPTER 2 PANEL LOCATION 2-1 FRONT PANEL CONTROLS ① ② ③ ⑨ ⑩ ⑪ ④ ⑫ ⑬ ⑤ ⑭ ⑮ ① REC Start or stop recording. ② PLAY Play back in normal speed. ③ T-SRH Display the search menu. ④ USB 2.0 Port Port for USB external devices. ⑤ LED Display (From left to right) ⑥ IR Sensor ⑦ ⑥ ⑯ ⑰ ⑦ ⑧ ⑱ Power: Power is on. HDD: Hard disk is in use. LAN: Connected to the internet (in red): Remote user logged in. REC: Recording. PLAY: Playing back. Input sensor for the remote control.
PAGE 10
2-2 8CH REAR PANEL CONNECTORS ① ④ ② ③ ⑤ ⑥ ① VGA VGA port ② DC 12V DC 12V power jack ③ MAIN/SPOT monitor MAIN/SPOT monitor BNC Video output ④ VIDEO IN For cameras BNC input ，8 ports ⑤ AUDIO IN RCA input( For CH1) ⑥ AUDIO OUT RCA output ( For CH1) ⑦ RS485 RS-485 for PTZ ⑧ LAN Network port ⑨ USB 2.0 For mouse MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 11
2-3 4CH REAR PANEL CONNECTORS ③ ① ② ④ ⑤ ⑥ ① DC 12V DC 12V power jack ② VIDEO OUT MAIN/SPOT monitor BNC Video output ③ VIDEO IN For cameras BNC input ，4 ports ④ AUDIO IN RCA input( For CH1) ⑤ AUDIO OUT RCA output ( For CH1) ⑥ VGA VGA port ⑦ USB For mouse ⑧ RS-485 RS-485 for PTZ ⑨ LAN Network port ⑦ MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 12
CHAPTER 3 LIVE, PLAYBACK AND PTZ OPERATIONS The IR remote control and mouse operate differently under each mode; this chapter describes the functions of them under three different modes: LIVE, PLAYBACK and PTZ. 3-1 LIVE Mode You can monitor all the channels, listen to audio signal and have some related operations under LIVE mode. This paragraph describes the IR remote control, mouse operation and on screen graphical icons under LIVE mode. Table 3-1.
PAGE 13
Table 3-1.2 Graphical icons that will display after right-clicking your mouse under LIVE mode. Icon Description Resting the cursor on this icon will bring up the following four menu icons. Main menu. Search menu. Backup menu. PTZ mode. Turn on/off recording. Playback. Resting the cursor on this icon will bring up the following five display icons. FREEZE. ZOOM, double the screen size AUTO-sequence LOCK, activate the key lock. Full screen display. Quad display.
PAGE 14
Table 3-1.3 Description of on screen graphical icons in LIVE mode Icon Description Recording is on Schedule Recording is on Live Audio is on Live Audio is off Motion detected on the channel Video loss detected on the channel USB device detected Connected to the LAN cable.
PAGE 15
3-2 PLAYBACK Mode Switch to PLAYBACK mode by pressing “PLAY” under the LIVE mode, the graphical icon will show up on the upper center of the screen and the operation panel ( see below picture) will show up at right lower corner of the screen. You can drag the panel by mouse to place it on any location of your screen. Table 3-2.1 Remote control functions under the PLAYBACK mode Button Description ENTER / MODE Switch to full screen, quad MENU / Turn on/off PAUSE. PLAY Play back at normal speed.
PAGE 16
Table 3-2.2 The mouse operation under the PLAYBACK mode. Icon ／ Description 「 / 」 Fast rewind 「 / 」Fast forward Play/pause 「▲ / SLOW」，slow playback 「▼ / ■」stop playback Playback channel by channel with snap shot display Full screen display Quad display 9 screen display Zoom-in display If you want to monitor single channel, please choose a channel and click left butt on of mouse two times. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 17
3-3 PTZ Mode Switch to the PTZ mode by pressing “PTZ” button under the LIVE mode. The PTZ icon will appear on upper left side of screen and the control panel will appear on the down right side of screen. Table 3-3.2 Mouse operation under the PTZ mode Icon Description Leave PTZ Mode，back to the LIVE mode Pre-set number N. (0~255) Go to pre-set number N. Set current PTZ location at pre-set number N. 「TOUR」，press to activate pre-set tour＊「PIP」，Set current PTZ location as the start of line-scan.
PAGE 18
CHAPTER 4 MAIN MENU SETUP To enter the main menu and set up DVR, log-in account and user password are required. The default password of the administrator is “123456”. Please check the “Account Setup” for related setup of other log-in users. Table 4-0.1 Some definition of virtual keyboard. Item Description Switch between capital and small letters. / Switch between numbers and letters. Press to cancel the setup, and re-choose the login account. Delete the last character. Enter to identify the password.
PAGE 19
Table 4-0.2 The operation of remote control under the setting menu Item MENU ESC ENTER Description Switch to different options under one item Switch to different items Save setup and back to LIVE mode Back to Upper level of menu without saving Enter the menu, or display virtual keyboard PS. The initialization of new-installed HD is required before recording, please refer to “4-9 UTILITY SETUP” for detail.
PAGE 20
4-1.1 Quality & Frame Rate Setup Item Description Normal setup/ event setup Select recording mode Select recording resolution: NTSC:352x240, 704x240, 704x480 Resolution PAL:352X288,704X288,704X576 Record Type You can setup quality and FPS separately for record type. No. Check/uncheck the box enable/disable selected channel recording Quality Select quality: Below Basic/ Basic/ Normal/ High/ Highest FPS Select recording frame rate.
PAGE 21
4-2.1 MOTION SETUP Item Description Alarm Duration(Seconds) When motion detect，the number of seconds continuous alarm 1~4 You can setup independently for each channel. Enable Check the box to Enable/Disable motion detection for each channel. Sensitivity Motion Area Setup Drag the white bar or press ◀ ▶ to set up Sensitivity from valu e 1 to 10 for each channel. The lower value you set the highe r sensitivity it will be Enter to setup motion detection area 4-2.1.
PAGE 22
Item Description Mask Mouse Selection Switch between “select” and “deselect” for cursor-dragging function All Area Detection Select entire screen as detection area. Mask All Area Deselect entire detection area. Continue Continue setup Exit & Save Save setup and leave Exit & Discard Cancel setup and leave 4-3 SCHEDULE SETUP Except from starting recording manually, you can also setup the recording time by weeks and schedule including normal, motion detect, and recording type.
PAGE 23
4-3.1 Schedule Record Setup Click on the time on the left side. The setup menu will be displayed. You can have detail setup by dates, Time and event. 4-3.2 Holiday Setup Since holidays are different by different country and region, you can setup the holiday of your location accordingly. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 24
4-4 CAMERA SETUP Item Description 1~4 Mask You can setup independently for each channel. Check the box to Enable/Disable mask function for LIVE mode Sharpness Drag the bar or press ◀ ▶ to adjust Sharpness of your camera from value 0 to 15. The default value is 1. Brightness Drag the bar or press ◀ ▶ to adjust Brightness of your camera from value 1 to 255. The default value is 128. Contrast Drag the bar or press ◀ ▶ to adjust Contrast of your camera from value 1 to 255. The default value is 100.
PAGE 25
4-5 ACCOUNT SETUP The Account Setup menu is used to provide role-based permission independently setting for each user (maximum of 4 users) to access DVR over network. The default admin account and password is “admin” and “123456” (The default password remains the same after firmware upgrade) Item No. Username Password Permissions Change Admin Password Picture Description Check to activate the user’s account. Set up username Set up password for each user.
PAGE 26
4-5.2 User Picture Setup User can select picture wished to be changed to from hard drive. 4-6 NETWORKING SETUP Item Description Connect type Setup mode for network connection: (ADSL、DHCP、LAN、3G). HTTP Setup Enter to set up HTTP DDNS Setup Enter to set up DDNS Mail Setup Enter to set up mail 3G Setup Enter to set up 3G network MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 27
4-6.1 NETWORKING SETUP There are three ways to connect to the network as followed. 4-6.1.1 DHCP When DHCP is selected, IP address will be assigned by DHCP server automatically. 4-6.1.2 LAN Select LAN for network connection, the following information is required. Item Description IP Address Enter IP address provided by ISP Subnet Mask Enter IP address of Subnet Mask provided by ISP Gateway Enter IP address of Gate way provided by ISP DNS Enter DNS address provided by ISP.
PAGE 28
4-6.1.3 ADSL Select ADSL for network connection, the following information is required. Item Description User Name Enter user name provided by ISP Password Enter password provided by ISP 4-6.1.4 3G Select 3G for network connection, the following information is required. Item Description Dial-up Number Dial-up Number，Determined as the ISP PIN Enter SIM card password APN Enter ”internet” Advance Setting The advanced settings (Taiwan ISP outside) MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 29
Item Description Enable Enable advance setting User Name Enter ISP username Password Enter ISP password IP Address Enter the ISP provides a fixed IP address。 (if the client uses the Internet only need to enter a fixed IP) PS：This feature currently only supports the Huawei 3G card 4-6.2 HTTP Setup Item Description Enable HTTP Server Check to enable HTTP server. Users can remotely access into the DVR over the network if the HTTP function is activated.
PAGE 30
4-6.3 DDNS Setup Item Description Enable/disable DDNS function. Enter the registered SMTP Server: ez-dns＊、I-DVR.NET＊、DYNDNS.ORG、NO-IP.ORG、3322.ORG Host Name Enter the completed registered SMTP Server. (Including username + Server) If the user name is h.264 and you choose i-dvr as your server, you should enter: h.264.i-dvr.net User Name Enter user name. Password Enter password. ＊For more detailed I-DVR.
PAGE 31
4-6.4 Mail Setup When event occurs (VLOSS, MOTION), email will be sent to the receiver account automatically. Item Description User Name Check the box to enable/disable E-mal Notification function. Enter to set up SMTP Server name. (Varies according to the user) Enter to set up User Name. Password Enter to set up Password. Sender E-mail Enter to set up e-mail address of receivers.
PAGE 32
4-7 PTZ & RS485 SETUP The DVR allows users to control PTZ functions of your camera. To enable PTZ function, the 485 cable should be connected to the RS-485 port of DVR. Item Description Enable PTZ Click the box to Enable/Disable PTZ function for each channel. Protocol Set up the protocol of PTZ cam. The supported protocol are PELCO-P, PELCO-D, KND, LI-LIN, SAMSUNG, LG, AVTECH. PTZ ID Baud Rate RS-485 ID RS-485 Baud Rate Keyboard Click or press ◀ ▶ to set up PTZ ID.
PAGE 33
4-8 SYSTEM SETUP Item Description DVR Name The name of DVR will be shown when users login from remote access. DVR Location The location of DVR will be shown when users login from remote access Language Click or press ▼ to select OSD language. Remote ID Default ID is 0. DVR is controlled by standard remote control, Display Setup Enter to set up Display Date/Time Setup Enter to set up Date/Time Device Setup Enter to set up Buzzer & Relay Spot Setup Enter to set up Spot 4-8.
PAGE 34
Item Description Auto-Seq Interval Set up duration time in seconds for the interval between channels under Auto-Seq mode. Show OSD Turn On / Off OSD display Show DVR Status Turn On / Off DVR illustration and record status display Show Date/Time Turn On / Off date and time display Show Channel Name Turn On / Off channel name display CRT Deflicker(only for CRT monitor) Border Color Set up the color of border in LIVE , PLAYBACK mode.（Red, Green, Blue） 4-8.
PAGE 35
4-8.2.1 CHANGE DATE & TIME Setup date and time of DVR manually according to user’s local time. 4-8.2.2 TIME ZONE AND DAYLIGHT SAVING TIME SETUP Set up time zone and activate Daylight Saving Time function according to user’s DVR location. Item Description Select Time Zone Enter to modify GMT from GMT- 13 to GMT+ 13 Daylight Saving Time Turn on/ off Daylight Saving Time MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 36
4-8.2.3 INTERNET TIME SETUP Synchronize your DVR time with internet time server. Item Description Automatic Synchronization Check to enable DVR automatic synchronization function. Effective by this option selected, DVR will automatically synchronize the time upon rebooting or by every 24 hours after booting. Update Now Effectively, Date and Time show on DVR will immediately correspond with those in internet server. 4-8.
PAGE 37
Item Description Key Tone Enable/Disable keystrokes. Buzzer Enable/Disable buzzer operation when the alarm is triggered for HDD Error, Motion and Vloss (Video Loss). MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 38
4-9 UTILITY SETUP Item Description HDD Initialization Select to enter hard disk initialization menu. Please stop recording before entering this menu. Enter the menu, system will show all the data (model ,volume ) of HDD that installed in DVR. Check the HDD you’d like to initialize then press “Start”. HDD initialization is successful when the status shows “Succeed” USB Initialization Clean up all data on USB. Enter USB initialization and press YES to clean up all data on your USB.
PAGE 39
4-10 DIAGNOSTIC Item Description Version The current firmware version of DVR IP The connected IP address of DVR. If disconnected from network, the screen will display” NETWORK DISCONNECT”. MAC MAC Address of DVR HDD Status No. HDD number Volume HDD Capacity Used Rate Percentage of space used on HDD. Shows HDD status. Status Format Time USING means the HDD is being used for recording now GOOD/BAD means the HDD has a known/unknown format for the DVR.
PAGE 40
CHAPTER 5 BACKUP & SEARCH 5-1 BACKUP SETUP User can backup any segment of recorded data in a specified time frame. To do so, either a CD R/W or storage device, like USB, must be connected to the DVR.
PAGE 41
iFileplay Use Method Step 1: install 「iFileplay」software to your PC. You can get「iFileplay」file from the CD with DVR Packing. PS: When you using USB to backup file, iFileplay.exe will copy to USB with the backup file automatically. Step 2：Setup「ifileplaypack.exe」。 Step 3：Click「open」，choose and star a DVR backup file。 MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 42
Step 4：Ifileplay software will play the backup file automatically. Step 5：If there is no display on the screen, The backup file is not our DVR recording format. Please check it. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 43
5-2 SEARCH SETUP Item Description Event Search Event search menu Time Search Enter time search menu 5-2.1 EVENT SEARCH The DVR automatically records events with type, time and channel information included. If there is recording data for an event, a yellow signal will be shown on the left side of time information. Rest your cursor under the line and press “enter”, or left click your mouse to playback the recording data. P.S.
PAGE 44
Item Criteria Page Date/Time Event Type Info Description Setup conditions of event search Switch between pages of events Date/time when event occurred. Event type, defined as following Motion Detected MOTION Video Loss Video Loss Remote Login user log-in over the network Remote Logout user log-out over the network Power On DVR Power on HDD Full HDD Space FULL HDD Error Detect HDD error Reboot DVR Reboot The channel where event occurs or login user 5-2.1.
PAGE 45
5-2.2 TIME SEARCH TIME SEARCH can search for the specific time of recording data to playback. Press “Enter” or left click on the desired date to playback. Note that dates with recording data are marked with a red square “ □ “System will start playing back according to the date you selected. Calendar will be shown by using mouse to click on “year” and “month”. Click “date” to display recording time of that specific date with time bar.
PAGE 46
CHAPTER 6 Remote Software Installation and Setup 6-1 AP Software Installation and instruction AP software:「DVR Remote Desktop」can allow you to remotely access and control the DVR from PC. p.s. Operation system currently supports Windows XP SP2 and above and Window s Vista, Windows 7 Step One：Enter the IP address of DVR in IE browser Step Two: Windows as below will show up. Please enter the user name and password. Default user name and password is admin/123456.
PAGE 47
Step Four: Run or Save our AP software. Step Five: If you choose to run the software, Start window will be shown up. Please enter information of login DVR: IP, Port, Username and Password, or choose “Play Recorded File” to open backup files in your PC. Step Six: You’ve logged into the DVR MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 48
6-2 How to do remote monitoring through IE Step One：Enter the IP address of DVR in IE browser. The address appeared in this image is only for demonstration. Actual address is depending on the setup of on-site DVR. Step Two: Windows as below will show up. Please enter the user name and password. Default user name and password is admin/123456. Other related setup about user account and password, please check “4-5 Account Setup. “ The user name and password appeared in this image is only for demonstration.
PAGE 49
Step Four: DVR images appear. 6-3 How to do remote monitoring through JPEG VIEWER(Only Monitor Fun ction) Step One：Enter the IP address of DVR in IE browser. The address appeared in this image is only for demonstration. Actual address is depending on the setup of on-site DVR. Step Two: Windows as below will show up. Please enter the user name and password. Default user name and password is admin/123456. Other related setup about user account and password, please check “4-5 Account Setup.
PAGE 50
Step Three: Click on “Jpeg Viewer” Step Four: DVR images appear. PS : Only for viewer, without any operation function. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 51
6-4 AP Software Operation Open the file “DVRemoteDesktop.exe”; enter the information of DVR “IP address”, “Port” “Username” and “Password” and click “OK”. You should be able to login DVR successfully and start to use the software. The default username and password is 「admin/ 123456」 “DVRemoteDesktop.exe” AP software provides some extra functions for remote users. Please check Table 6-4.1 for minimum system requirements for “DVRemoteDesktop.exe” operation. Table 6-4.
PAGE 52
CHAPTER 7 SPECIFICAITONS 1. VIDEO Input Level 1.0 Vp-p±10% Composite, 75Ω Balanced Display Speed Display Resolution NTSC 120fps PAL 100fps NTSC 720(H) X 480(V) PAL 704(H) X 576(V) Monitor Output 2Vp-p Composite, 75Ω Balanced 2. RECORDING Compression Method H.
PAGE 53
Dimension 225(W) x 215(D) x 46(H) mm Weight 0.95kg ( without HDD) 9. BACKUP BACKUP USB Stick Video Data, Audio Network Video Data, Audio 10. SEARCHING & PLAYBACK Searching Type Event/ Time Playback speed 120 FPS 11. MULTI-REMOTE SURVEILLANCE Monitoring Environment Web / Client Software(CMS) Max. client Supporting multi-client (5 clients accessible) 12.
PAGE 54
CHAPTER 8 MOBILE APPLICATION INSTALLATION AND USAGE You can remotely monitor all channels of DVR through your mobile device. The required mobile application is from DVR manufacturer and it supports mobile OS for both Windows mobile 5.0 above and Symbian.
PAGE 55
8-1.2 Mobile Application Operation After the installation, enter the Program Files menu in your mobile device to run a file called “DVRH264”. Select “Menu” at the right lower corner of your mobile screen, 4 commands, Login Add Modify and Delete, will show up. 8-1.2.1 Add New Login DVR To log into the DVR, you need to enter the logging-in DVR information. Find “Add” under the “Menu” then enter logging-in DVR’s IP address, Port number, account name and password.
PAGE 56
8-1.2.3 Modify the Login Information of DVR You can use the “Modify” command to change the login information of DVR. The dialogue is identical to that of the “Add” command. 8-1.2.4 Delete the Login Information of DVR “Delete” command can be used to remove the DVR information if it is no longer useful. Select the DVR on the name list then choose “Delete” 8-1.3 Live Monitoring Operation This paragraph describes some operation under the LIVE monitoring mode in device.
PAGE 57
8-1.3.1 Scroll the Image You can use the keypad on your mobile device to scroll the image if it’s oversized. Key 2 4 6 8 Action Scroll Up Scroll Left Scroll Right Scroll Down 8-1.3.2 Image Quality Setup Select “Quality” under the “Menu” There will be 5 levels for your to choose: Low、 Normal、Middle、High and Highest. 8-1.3.3 Channel Display Select “Single” under the “Menu”, there will be all channels of your DVR in list for you to choose. PS.
PAGE 58
8-1.3.4 Size of Image The screen size of different mobile device can be different. You can select “Size” under the “Menu” to choose from “Original” or “Fit Screen” to resize the display image. Item Original Fit Screen Description The image will be shown in original size. The image will be shown to fit the screen. 8-1.3.5 Rotate the image The Live image can be displayed in normal or rotate to 90 degrees. Select “Rotate” under the “Menu” for this operation. 8-1.3.
PAGE 59
8-2 Mobile Application Installation and Operation for Windows Mobile There is one application for Window Mobile OS. The one for H.264 compression can transfer both audio and video signal to your mobile device. System Requirement: Mobile device OS：Windows mobile system 5.0 above. Mobile device need to support internet: GPRS／3G／Wifi… etc. 8-2.1 Mobile Application Installation Please follow the steps cited below to perform the mobile device surveillance function on your mobile device (mobile phone, PDA ...
PAGE 60
8-2.2 Mobile Application Operation After the installation, enter the Program Files menu in your mobile device to file named “DVRU264Pocket” and run “H264Pocket”program. This application allows you to remotely logon and monitor DVR. Press “OK” to bring up the operation menu, see below chart to further information. Item Function Description Enter DVR’s name, IP address, Port, Account user, Password Add Add login DVR then press “OK” •Choose the DVR that you’d like to log on , then press “OK” • PS.
PAGE 61
8-2.3 Operation under the LIVE monitoring. After successful log on the DVR, press “View” to bring up operation menu. You can choose the channel, resize the image, choose the quality, and turn on/off the status bar, alarm, full screen display….etc Item Function Channel 1~4 Display for CH 1~4 Status Bar Status Bar Description Choose from CH1~4 to display.
PAGE 62
8-3 Google Android Phone OS application and operation System requirements： Mobile Device operation platform：Google Android System。 Internet needed for Mobile device operation platform (GPRS/ 3G/ Wifi…etc.) In order to remote log in to DVR to live monitoring through mobile device, first of all, please follow the instructions for software installation: Step 1: Google Phone applications will copy and extract to the PC (or NB). File in the shipment CD-ROM of directory Mobile → Gphone → gphone2009_1201.
PAGE 63
Step 3: Click the implementation of the "gphone" directory → tools → installapk.bat This step will installed Google phone software directly connected to the Gphone. After installation, please press any key to exit. Step 4: In Gphone mobile , click , look and perform "Androidh264". MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 64
Step 5: Click "Menu" → Add new DVR Name, IP location, Port, User name and Password, enter the complete click Login. Step 6: Wait for a moment that will occur real-time video (according to the actual network speed, connection time needed may vary). Click the top "AndroidH264 (Press Menu)" Department to switch channels. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 65
8-4 Blackberry Operation System Software Installation and Operation System requirements： Mobile Device operation platform：Blackberry 9000 Internet needed for Mobile device operation platform (GPRS/ 3G/ Wifi…etc.) Software：Blackberry Desktop Manager v4.6 or above 8-4-1 Software installation In order to remote log in to DVR to live monitoring through mobile device, first of all, please follow the instructions for software installation: Step One: Visit Blackberry official website http://na.blackberry.
PAGE 66
Step Three：Run ”Application Loader” Step Four: Run “Add/Remove Applications” Step Five: Please copy”dvrh264.alx” and “dvrh264.cod” to PC. The software is available in the User CD that comes with each of DVR. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 67
Step Six: Find “dvrh264.alx” in Blackberry Desktop Manager . After activating the software, press “Next.” The software will be installed in Blackberry automatically. Remove USB cable after installation. Step Seven: After the software is installed completely, enter “Download” menu in the mobile device and execute program, “H264MIDlet” MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 68
8-4.2 Application Software Operation 8-4.2.1 Add new log-in DVR In order to connect to DVR, please input DVR information to the mobile device. Press “option” → “Add”, and then enter “DVR IP,” “port,” “log-in account,” and, ”log-in password.” Press “ok” to save. 8-4.2.2 Log in onto the DVR Multiple DVR information can be saved with this software, therefore, please choose the DVR that’s wished to be connected. Press “Option” → “Login” to log in to DVR for live monitoring.
PAGE 69
8-4.2.3 Modify the Login Information of DVR If DVR log-in information is wished to be modified, please select the DVR. Enter “Option” → “Modify” for editing the existing data. Press “OK” when it’s finished. 8-4.2.4 Delete DVR Existing Record (Connection Information) If DVR connection information is no longer needed, please select the DVR. Press “Option” → “Delete” to delete the DVR connection information. 8-4.
PAGE 70
8-4.3.2 Image size Due to the variety sizes of mobile device screens, this software offers two different methods for image display. Press “Size” in menu, and then there will be options, “Original” and “Fit Screen” available to choose from. Option Original Fit Screen Description Image appears as its original size. Image appears to be the most optimized size according to the screen. 8-4.3.3 Image Rotation There are two options for live image display.
PAGE 71
8-5 iPhone Software installation and operation 8-5.1 iTune software installation and registration STEP1: Download iTunes Visit Apple website http://www.apple.com/itunes/ to download & install the iTunes. Step 2 Register iTunes Store 2.1.1 Run the installed iTunes, you might need to create an account to visit iTunes store firstly. Move to the menu “Store”, and click the option “Create Account”. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 72
Step 3: Continue 2.1.3 Select & continue Step 4: Select & Continue 2.1.4 Fill in your personal info & continue. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 73
Step 5: Fill in your personal info & continue. Please note that the options of Payment Method are different from different regions, please select another payment method. Don’t worry, “SCDVR” is a free software & you don’t need to pay for it. Step 6: Finished the register, go to your email box to verify your account. Step 7: Click the link included in the email message. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 74
Step 8: It will connect to the iTunes store and turn to iTunes interface. Step 9: Sign in your account. Step 10: The register of your iTunes store account has been done. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 75
8-5.2 “scdvr” software installation ( From iTunes ) Step 1: Click iTunes Store(1), then input “scdvr” into the search bar(2) on the right upper corner and press Enter. 2 1 1 Step 2: You will find the ScDvr icon displayed as below. Click the icon and it will turn to the download page. Click the “FREE APP” button to download the file. Step 3: You will find the downloaded file on the directory of Application MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 76
Step 4: Connect your iPhone to the computer, you will find your Device displayed on the left si debar. Select the DEVICES ID(1), and then click “Applications” option(2). Select the “Sy nc Applications” & “ScDvr” (3) and then click “Sync” button(4). 2 3 1 4 ＊ The devices ID is different from different iPhones Step 5: After finishing the sync, you will find the ScDvr Icon on your iPhone. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 77
8-5.3 “scdvr” software installation ( From App Store ) Step 1: iPhone connect to internet ( GPRS/3G/Wifi…), and run App Store program. Step 2: Search the “Scdvr’’ program. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 78
Step 3: Show Scdvr information & “Free” icon. Step 4: Press “Free” icon till it become “Install” then click and run install progra m. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 79
Step 5: Sign in Username & Password. Step 6: Wait process complete. iPhone will generate a new ScDvr program. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 80
8-5.4 How to operate “ScDvr” program. Run ScDvr program in the beginning. 8-5.4.1 Add new DVR information. When you use ScDvr program first time, you must enter and save DVR’s information. Pl ease press the “Add” then enter the DVR’s Name/ IP/ Port/ Username/ Password, after t hese information fill. Click “GO” this button will connect to the DVR and save these DV R’s information automatically. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 81
8-5.4.2 How to log in DVR. “ScDvr” can store many DVR’s information, You can choose the DVR you need and pre ss “GO” to log in. The login take time depend on network bandwidth. Live view will appear when login suc cessfully. PS: The channel without recording cannot be live view. 8-5.4.3 How to change DVR’s information. If you need to change DVR’s information, please press the “Edit” and change the inform ation, run “GO” to save. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 82
8-5.5 How to use ScDvr to Live monitor. 8.5.5.1 Live display When Live view, click the lower window. A control table will appear. You can switch the Live View from CH1~CH4 and on/off the voice. Press the “Uidvr”. You can back to the previous page. 8.5.5.2 Rotate the display You can choose the live view display with original angle or 90/ 180/ 270 rotation angle f rom anti-clock direction when you press the “R” button right of the corner, MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 83
CHAPTER 9 CMS INSTALLATION AND USAGE GUIDE 9-1 CMS Installation System Requirement: ＊Intel Pentium 4 processor or equivalent. ＊Microsoft ＊Besides Windows Vista、Windows XP、Windows 2003 Server. OS and other required APs, there will be 512MB remaining memory needed or above. ＊512MB memory above.(500M requested for group DVR connection and 180M for single DVR) ＊20MB HD space. Recording and image capturing require extra space for storage.
PAGE 84
6. Select ‘Close’ to finish installation when the “Installation Complete” window shows. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 85
Instruction for Log-in Failure to CMS after Upgrade Log in to CMS with the default account and password after CMS upgrade. If an error message occurs as shown in the image, please follow the instruction to solve the error. Step 1: Please enter file manager to enter folder, “Windows” and then folder “Systme32” (ex:C:\Windows\System32) Step 2: Locate file, “iCMS.dat” and delete it. Step 3: Restart CMS. Log-in successfully. 9-2 CMS LOGIN AND MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 86
ENVIRONMENT To enter CMS, the administrator’s user name and password are required. The defaults are ‘admin’ and ‘123456’. After successful login, the following image shows on your screen: ③ ① ② ④ ⑤ ① DVRs, Groups & Events Information about DVRs, groups and events. See “9-3 Information List” for more detail. ② PC information and control Information about local PC’s hard disk, volume, recording...etc. See “9-4 PC Information and Control” for more detail. ③ Main Display Live image display area.
PAGE 87
9-3 DVRs, Groups & Events Icon Description View list of logged in DVR／ Group. View Logs: list all the event information of DVR 9-3.1 View DVR／Group List Single left click on ‘DVR’ or ‘Group’ will expand/collapse the entire DVRs and groups list. On the DVR list, double left click on a connected DVR will show its image in main display. See “9-6.2 DVR Administration” for further information.
PAGE 88
9-3.2 View Event Logs Under this page, all the events of a DVR can be expanded/collapsed in the order of Re mote in/Remote out, Video Loss, Motion, Sensor, Others (Power Reset, Key Lock, Key Unlock, HD Full). 9-4 Local PC Information and Control Located at the left lower corner of the screen, please see the chart below: Icon Function Description HDD info Shows the ratio of available space / HDD capacity of C:\ drive (where CMS is installed). Recording Directory Setting Recording Directory.
PAGE 89
9-5 Main Display The main display area is where the live image of DVR is shown. You can drag to change the location of screen for each channel and turn on/off audio signal with mouse-click. 9-5.1 Audio Control In live mode, you can turn on/off the audio signal of Ch1~Ch4: 「」Audio signal is On 「」Audio signal is Off Turn on/off by clicking on the graphical icon, please note there can allow only one chan nel’s audio signal to be on at one time. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 90
9-5.2 eMAP Display In Live mode, pressing will bring the e-MAP drag-down menu. If the channel has been set up to use e-MAP, the menu will show all the e-MAP titles that have been entitled to this channel; otherwise, “No eMaps” will be shown. Please check “9-6.4 eMAP administration” for setup information. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 91
9-5.3 PTZ Control In the main display, right click on the channel will bring up PTZ control panel as below. Icon 8 direction key Description Rotate the PTZ ZOOM+：Zoom in ZOOM : Zoom out Setup the PTZ spot as pre-set N. FOCUS+ : Focus in FOCUS-：Focus out Move to pre-set N. Set PTZ Preset Goto PTZ Preset PTZ Sensitivity Setup 16 pre-set N. Move to specific pre-set N. Activate auto pre-set tour＊ Setup PTZ sensitivity＊ Setup the “start” and “end” of liner scan.＊ Activate the liner scan cruise.
PAGE 92
9-6 Operation Bar 10 Operations to be listed as below: Table 9-6.1 description of 10 operations: Icon Description User Administration. Please see “9-6.1 User administration” DVR Administration. Please see “9-6.2 DVR Administration” Group Administration. Please see “9-6.3 Group Administration” eMap Administration. Please see “9-6.4 eMap Administration”. Remote Playback. Please see “9-6.5 Remote Play”. HDD Playback. Please see “9-6.6 HDD Play” File Playback. Please see “9-6.7 File Play” Event Playback.
PAGE 93
9-6.1 User administration Before the CMS can be used on a PC, user accounts should be added with proper authority. Each user should also be assigned a password and optionally a description. If a user does not have certain authority assigned, he/she will not be able to operate the corresponding function on the Operation Bar. The default is none of the authority is assigned. The administrator should assign proper authority to each user. These user accounts can be deleted or edited later on.
PAGE 94
9-6.2 DVR Administration DVR connections can be added to or deleted from the CMS and their information can be edited. DVR’s channel names can be entered here or downloaded from the DVR by pressing ‘From DVR’. Select “OK” to save the information.
PAGE 95
3. Check the specific channels that you’d like them to be included in the group. To include all channels of a DVR, just check the DVR.(1 Group up to select 64 camera) 4. Click “OK” to return to the previous window. 5. Select a display mode. 6. Drag a channel from the lower left panel into the main display to a preferred location. Or, change the channel location in the main display by mouse dragging. 7. You can ‘Select’ again to add other channels, but the un-saved channel locations will be lost. 8.
PAGE 96
9-6.4 eMap Administration If geographical locations are relevant, or if it is desired to use a picture as the background, eMap can be used for the purpose. With eMap, the background picture can be picked by the user and channels from multiple DVRs can be placed and dragged around on the picture. Steps to follow: 1. Click and a path for the picture will be prompted. 2. Select a picture, click OK and the picture will show in the right panel. 3.
PAGE 97
5. Click OK to save. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 98
9-6.5 Remote Play Video images recorded on a DVR can be displayed on a remote CMS. With Remote Play function, select a DVR and a display mode on top of the screen. After the recorded segments are listed below, double click on one to show its image on the right. Icon Description Start playing. Pause. Fast forward. Fast rewind. Select the clip you want to watch the number of minutes and seconds,Press the right button is set to start playing MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 99
9-6.6 HDD Playback You can directly play the recording data in the HDD that’s uninstalled from DVR by CMS. See the picture below, the left part of screen is recording data in list that’s separated by hour and the right part is main display. You can change the display modes and play files fast forward or rewind. Icon Description Start playing. Pause. Fast forward. Fast rewind. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 100
9-6.7 File Playback You can play the recorded .irf files by “File Play” in CMS. It allows you to change the display mode, forward or rewind the file and drag the time bar. Icon Description Start playing. Pause. Stop playback. Fast forward. Fast rewind. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 101
9-6.8 Event Playback Event recordings on the DVR can be played back in CMS. Steps to follow: 1. Select a DVR and a display mode. 2. Select a date. 3. Double click an event and play back the images on the right. Use buttons at the bottom to control the playback. 9-6.9 Snapshot Data It can display all the snapshots you’ve taken in line in “Snapshot Data”. You can review, delete or save as other files here.
PAGE 102
9-6.10 Recording Data It can play all the recording files you’ve recorded in line in “Recording Data”. You can play or delete them here. Steps to follow: 1. Choose the recording time at upper left corner, it will be played on the main display. 2. You can choose the display mode. 3. Time bar will be shown at right lower corner, please drag the time bar to specify the recording time you’d like to play. Icon Description Start playing. Pause. Stop playback. Fast forward. Fast rewind.
PAGE 103
APPENDIXⅠ I-DVR.NET REGISTRATION DDNS Registration on I-DVR.NET In the package of each DVR, you will find a sticker shows account information including username and password that allows users to login I-DVR.NET for registration. To register DDNS on I-DVR.NET, please follow the steps as shown. Step 1. Please open IE browser and then enter “ http://i-DVR.NET/logon.asp ” in IE browser bar. Next, “Control Panel Logo” dialog will appear.
PAGE 104
Step 4. Enter DVR →Main Menu → Network Setup → DDNS. Activate DDNS functions and input related information. DDNS work properly when this option selected. Step 5.Back to the i-dvr.net, on this page by pressing "F5: Refresh", IP will be automatically updated into the DVR of the real IP location. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 105
APPENDIXⅡ ez-dns REGISTRATION DDNS Registration on ez-dns.com In addition to I-DVR.NET the Company, the other has a ez-dns.com server may be used.. To register DDNS on ez-dns.com, please follow the steps as shown. Step 1. Please open IE browser and then enter “ http://ez-dns.com ” in IE browser bar. First time, please click on the top of the screen of "Sing up" (red box ) Step 2. To input a user name and password, after clicking “singup”. Later, log in to use ez-dns.
PAGE 106
Step 3. The “host.domain” column will show up the setup just entered. Next, enter the DVR the same time setting the DDNS client machine information If DDNS set up at DVR side successfully, the website will update the IP information in 10 minute. The IP column will be renewed to the corresponding IP address by pressing “F5: refresh” button. “host.domain” is named by your choice. “demodvr.ez-dns.
PAGE 107
DDNS work properly when this option selected. This part of the information required and the same within the ez-dns.com Step 5.Back to the ez-dns.com, on this page by pressing "F5: Refresh", IP will be automatically updated into the DVR of the real IP location. MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 108
APPENDIXⅢ Remote Monitoring IE ActiveX Control Installation Instruction When using IE for remote monitoring for the first time, IE ActiveX Control is needed to be downloaded. 1. When remote monitoring on IE for the first time, an alert message occurs “Install ActiveX control” on the tool bar. 2. Click at this alert message and select “Install ActiveX Control” 3. “Do you want to install this software” alert pops up. Select “Install” MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 109
4. After installation, IE remote monitoring image appears. 5. If message, “Your security Settings do not allow web sites to use ActiveX controls installed on your computer.” pops on when logging in, please follow the next instruction. 6. First select “Tools” on the tool bar and then select “Internet Options” MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 110
7. Select Security →Trusted Sites → Sites 8. Enter DVR address (This address is only for demonstration. Please use the address depends on the setup of on-site DVR.) into the blanks shown in picture, and then press “add.” MAGTEC MT854 4 channel DVR User Manual V1.
PAGE 111
9. Newly added website will appear at the trusted web sites list. Press close. 10. Go back to IE window, press refresh button or F5. MAGTEC MT854 4 channel DVR User Manual V1.