Operation Manual

ManualsBrandsMagnum ManualsAir ConditioningE control

 E-Control

User- and installation manual

Dated March 1

2004

Important:

Switch off power before connecting or disconnecting wiring to thermostat.

A qualified electrician to current IEE regulations must install all wiring, failure to do so may invalidate

the warranty.

Introduction:

The ME-control thermostat is very user friendly and has intelligent software to guide the user

throughout the whole menu-structure. The thermostat is capable of switching your underfloor heating

system on and off, up to four different times of the day. The ME-control has an automatic Setback

period. The setback periods are the events between your comfort periods. This will lower your room

temperature as well as your energy costs without reducing the comfort.

In order to program just follow the onscreen information, you will be guided through the different

menus and functions automatically.

Nevertheless it is strongly recommended to study the operators manual carefully and keep it for future

reference.

The ME-Control has a 3-button structure:

Middle button : Selection button, higher/lower and Scroll through options.

Right button : to confirm choices/settings and to proceed.

Left button : to rectify wrong choices and settings.

* Some menu parts contain more program choices than displayed at first sight. Use middle

button to scroll down until “Back to main Screen” is displayed, this is always the last choice in

all menus.

Summary of content (6 pages)

PAGE 1
E-Control User- and installation manual Dated March 1st 2004 Important: Switch off power before connecting or disconnecting wiring to thermostat. A qualified electrician to current IEE regulations must install all wiring, failure to do so may invalidate the warranty. Introduction: The ME-control thermostat is very user friendly and has intelligent software to guide the user throughout the whole menu-structure.
PAGE 2
Start up menu: When switching the thermostat on for the first time, you will be asked a series of questions about your heating system. 1. Language - you have a choice between English, German & French 2. Date - set to present date 3. Time - choose between 12 & 24 hr clock, then set to present time 4. Heating system - choose “with floor sensor” 5. Floor thickness - Enermat (floor adhesive & tiles) or Enercable (<5cm, <10cm or >10cm) 6.
PAGE 3
At the same time, the appearance of main-screen is the confirmation that all standard settings or preprogrammed settings are fully operational. Use the auto-program as confirmed in Start menu approx. 14 days after date of activation. In this way the memory of the thermostat is able to store and adapt historical temperature movements.
PAGE 4
Press Menu button for permanent changes and next options appear in display: Options Explanation 1. Program/Comfort temperature: Change Comfort temperature. Change the 7 days program to your preferred times. (To activate 7 Days program – return to main screen, press Mode and scroll to Thermostat Auto and confirm). Return to Factory Settings. 2. Date/time : Date & time can be accessed and changed 3. Other functions : *See explanation other functions 4.
PAGE 5
Disturbances, failure signals and/or wrong readout of information: 1. Return to Start menu: in main-screen press the Menu button, select other functions and confirm, select Reset All and confirm again. Select language …..the first question of the Start menu will appear in the display and proceed. 2. Switch the current off/on and try again. 3. Switch off the power, remove the thermostat and check if all wiring is connected correctly. 4.
PAGE 6
Technical Details: Supply voltage Output relay Temperature range Housing : 230V - 50/60 Hz : Max. 16 Amps. / 230V : +5/+40ºC (Option ºF) : IP20 Built in back box (deep 50mm single switch back box) according to Standard DIN sizes Delivered incl. built-in sensor and external (floor) sensor Colour : Polar white (RAL 9010) Guarantee : 2 years manufacturers guarantee Approvals : VDE / FI / CE / CCA Manufacturer : C&F Technics, The Netherlands More information: ENERfoil magnum LTD P.O.