Manual

our Cable TV input into your home may be a single (75 ohm)
able or use a cable box decoder. In either case the connec-
tion is very simple. Follow the steps below to connect your cable
signal to your new television.
Direct Cable Connections:
This connection will supply Stereo sound to the TV.
Connect the open end of the round Cable Company sup-
plied cable to the 75f2 input on the bottom of the TV. Screw
it down finger tight.
Direct Cable Connection:
Cable signal
coming trom
Cable Company
(Round 75ff2
coaxial cable)
oo.
F
Jack Panel Bottom of TV
.+o
Cable Box (w/RF In/Outputs):
This connection will NOT supply Stereo sound to the TV. The sound
from the cable box will be mono.
Connect the open end of the round Cable Company sup-
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
Using a separate round coaxial cable, connect one end to the
OUT(put) (TO TV) plug on the back of the Cable Box.
Connect the other end of the round coaxial cable to the
75f2 input on the bottom of the television. Screw it down fin-
ger tight.
NOTE: Be sure to set the OUTPUT CHANNEL SWITCH on the
back of the cable box to CH 3 or 4, then tune the cable box on the
TV to the corresponding channel. Once tuned, change channels at
the cable box, not the television.
Cable Box with RF Inputs and Outputs Connection:
Cable Signal
1N from the
Cable
Company
CABLE
IN
TO 'T'V
Output Channel Switch
OUTPUT
CH
3 4
II II
L_J
Jack Panel Back
of Cable Box
Round 75
Coaxial Cable
oo+
Jack Panel Bottom of TV
HDinput 75 g2r COMP
VmEO
Cable Box (w/Audio/Video Outputs):
This connection will supply Stereo sound to the TV.
Connect the open end of the round Cable Company sup-
plied cable to the cable signal IN(put) plug on the back of
the Cable Box.
Using a RCA type Video Cable, connect one end of the
cable to the Video (yellow) (or ANT, your cable box may be
labeled differently) Out jack on the cable box madthe other
end to the Video Input on the bottom of the TV.
Using a RCA type Audio Left mad Right Cable, connect one
end to the left and right Audio Out L & R jacks (red &
white) on the cable box. Connect the other end to the Audio
L & R Input jacks on the bottom of the TV.
NOTE: Use the SOURCE button on the TV remote control to tune to
the AV1 channel for the cable box signal. Once tuned, change chan-
nels at the cable box, not the television. Pressing the SOURCE button
repeatedly will scroll all the AV Input channels, including the present-
ly tuned chmmel.
Cable Box with Audio/Video Outputs Connection:
Cable Signal IN
from the Cable
Company
CABLE
0trOUT
@ ° @@@
3 4
TO VIDEO
OUT
Jack Panel Back
of Cable Box with A/V Outputs
/
Video Cable,
Audio Cables
L & R (Red, White)
Jack Panel Bottom of TV
A ombination antenna receives normal broadcast chan-
nels (VHF 2-13 and UHF 14-69). Your connection is
easy because there is only one 75Q (ohm) antenna plug on
the back of your TV, and that's where the antenna goes.
If your antenna has a round cable (75 ohm) on the end,
then you're ready to connect it to the TV.
If your antenna has fiat, twin-lead wire (300 ohm), you
first need to attach the antenna wires to the screws on a
300- to 75-ohm adapter.
Push the round end of the adapter (or antenna) onto the
75ff2 (ohm) plug on the bottom of the TV. If the round end
of the antenna wire is threaded, screw it down finger tight.
Antenna Connection:
Outdoor or Indoor Antenna
(Combination VHF/UHF)
The combination antenna receives normal
broadcast channels 2-13 (VHF) and 14-69 (UHF).
\_X_//_/'/////_///_ 300_d7p5t;oh m
Twin _XII __ _
Lead Wire I K,j¢@_' I
t I
Round 75_
Coaxial Cable
from Antenna
Jack Panel
Bottom of TV