Installation and Operation Manual POWER EJECT DIM ELAPSE LOUD AS/PS 4 X 50W PULL OPEN MARINE CD RECEIVER SHIFT SCAN MODE VOLUME MAIN OTE VOLUME REM PGM SHIFT CH TRK TUNE TRK SEL BAND TUNE 1 MEM 2 PGM 3 RPT 4 RDM MUTE DISP 5 INT M6100CD Waterproof AM/FM/WB and CD Stereo Receiver A Registered Trademark of Magnadyne Corporation
Introduction Your new M6100CD entertainment system has been designed to give you many years of listening pleasure. Take a moment to read through this manual and become familiar with the operations and features of this outstanding product. It is advisable to keep this manual in your vehicle so it is readily available for reference. Be sure to fill out and send in your warranty card to ensure that you receive the full benefits of warranty repair in the unlikely event that your system will need service.
Location and Function of Controls at a Glance 8. Multi-Function Button 3/RPT: Radio: Recalls a memorized radio station, and programs a radio station into memory (See Radio Operation for more information). CD: Continuously repeats the same track (See CD Operation for more information). 9. Multi-Function Button 4/RDM: Radio: Recalls a memorized radio station, and programs a radio station into memory (See Radio Operation for more information).
Radio Operation Listening to the Radio 1. Push the “POWER” button (1) once to turn the unit on. 2. Press the “BAND” button (11) to select a radio band: FM1, FM2, FM3, AM or WX (weather band). 3. AM or FM Station Selection Automatic Seek Station Selection: Press the TRK/TUNE DN or TRK/TUNE UP button (5) to automatically seek the next strong station. SHIFT Scan Station Selection: Press the button (14) to automatically scan through strong stations in the current radio band.
General Operations Setting the Clock 1. Press DISP button (12) for more than 3 seconds until the clock shown in the display area is flashing. 2. Press the TRK/TUNE DN button to adjust the hours 3. Press the TRK/TUNE UP button to adjust the minutes. Display Priority Clock Display Priority: Press and hold DISP button (12) while pressing the TRK/TUNE DN button to select Time Priority. Pressing the DISP button while in Time Priority will temporarily display selected station frequency.
CD Player Operation Inserting and Ejecting a Disc Pull the tab at the top of the CD Door, and the door will open. Push a disc into the CD Slot (18), label side up, and the disc will begin to play. The disc will eject automatically when the CD Door is opened. Select Tracks Press the TRK/TUNE DN or TRK/TUNE UP button (5) to move to the previous track or next track. The track number appears in the Display Area.
Waterproof Wired Remote General Operations (Optional) 8 7 6 MODE VOLUME TRK TUNE TRK MUTE 5 TUNE STEREO COMMANDER VOLUME POWER 1 BAND SHIFT/SCAN 2 3 1. Power Button: Press and release the POWER button (1) to turn on/off the unit. To program the initial volume level, adjust the volume to the desired level, then press the POWER button for more than 3 seconds. The next time the unit is turned on, the volume will be at this initial level. 2.
Waterproof Wired Remote Introduction This unit is a wired remote control made using a modified controller or similar layout. It is capable of operating the specified functions on the M6100CD receiver. The body, buttons, controls and display are UV and water-resistant. It includes a LCD and an illumination circuit. Take a moment to read through this section and become familiar with the operations and features of this outstanding product.
Wiring Step 1: The radio chassis is designed to be “Panel Mounted” through a opening in the mounting panel. See the installation part of this manual for panel mounting. Step 2: Bring all wiring for the connection of the unit (including the antenna) through the mounting hole. Connect the wiring as follows: Yellow Wire: Connect this wire to a constant +12 volt power source (a power source that is not controlled by the ignition key).
Wiring Diagram M6100CD Antenna Socket Red Right Channel RCA Connectors Set 1 Ignition Red Wire Switch (+12v in ) Battery (+12v in) Ground (B-) Connect to Line Input of Optional Amplifier White Left Channel Yellow Wire Red Right Channel Black Wire Power Antenna Blue Wire (Switched +12v out) RCA Connectors Set 2 Connect to Line Input of Optional Amplifier White Left Channel Left Main Speaker White Wire Gray Wire White Wire with Black Stripe Gray Wire with Black Stripe Left Remote Speaker Gr
CD Changer Connection CD Changer (Optional) M6100CD Male to Male 8-Pin Din Cable (Supplied with CD changer) 8-Pin Din Connector Auxiliary Connection VCR Audio Out From VCR / TV / Video Game M6100CD or TV Auxiliary Audio Input RCA with Yellow Cables Red RCA (Right) or White RCA (Left) Video Game Wired Remote Connection Wired Remote (Optional) M6100CD Female 8-Pin Mini Din Connector Male 8-Pin Mini Din Connector 11
Installation Remove Transportation Screws Before installing the unit, remove the two screws shown in the illustration below. Mounting Surface Mounting Location Remove screws before installation Mounting Holes 3. Use the glue paper to stick the two mounting brackets to the back of the mounting surface. The screw holes of the brackets must respectively aim at the mounting holes in order to fix the unit to the mounting surface.
Installation Sheet Metal Screw Nut Washer Metal Strap Mounting Surface Trouble Shooting Before going through the trouble shooting table below, check the wiring connection. If the problem persist, consult your nearest service dealer. SYMPTOM CAUSE SOLUTION No power The ACC Power Supply is not connected. Both the red and yellow wires require power from the power source. The fuse is blown. Replace the fuse. Presence of disc inside the player.
Specifications GENERAL Power Supply Requirements: DC 12 Volts, Negative Ground CD PLAYER Signal to Noise Ratio: > 55 dB Channel Separation: > 50 dB Chassis Dimensions: 178 mm (W) x 165 (D) x 50 (H) Tone Controls: Bass: 100 Hz ±10 dB Treble: 10 kHz ±10 dB AM RADIO Frequency Coverage: 530 to 1720 kHz Sensitivity (S/N=20dB): 32 dBu Frequency Response: 40Hz – 18 kHz FM RADIO Frequency Coverage: 87.5 to 107.9 MHz Maximum Output Power: 4 x 50 watts Sensitivity (S/N=30dB): 3µV Current Drain: 15 Ampere (Max.
A Registered Trademark of Magnadyne Corporation © Copyright 2003 Magnadyne Corporation M6100CDUM Rev.
