Installation Guide

SPK A/B Volume/ Mute Control Operation
1. The volume of each set of speakers can be
adjusted independently. Short press the A or B
buttons to select the speakers that the volume
control will effect (LCD displays the "SPK A"
or "SPK B" icon). Pressing VOL +/- button will
change the volume of the speakers selected.
2. To control the volume of both sets of speakers
at the same time, press and hold either the A
or B button for 2 seconds (LCD will display
"SPK A" and "SPK B" icon).
3. To mute the sound of all speakers, quick
press the power
button. All speakers will be
muted. Quick press the power button again
to resume the current volume level.
Note: To bring all speaker outputs to the same
volume level, short press the A or B buttons
then press and hold the volume (-) until both
volume levels reach zero. From that point,
press the volume (+) button and all speakers
will rise in volume together.
Bass, Treble and Balance Control:
Select the desired sound mode to adjust by
short pressing the SEL button. The modes will
be displayed in the following order: Bass, Treble,
Balance EQ, Loud.
Bass:
Select the Bass mode by short pressing the SEL
button. Adjust the level of Bass by pressing the
VOL +/- buttons. After 5 seconds control reverts
back to volume control.
Treble:
Select the Treble mode by pressing the SEL
button. Adjust the level of Treble by pressing the
VOL +/- buttons. After 5 seconds control reverts
back to volume control.
Balance:
Select the Balance mode by pressing the
SEL button. Adjust the Balance by pressing the
VOL +/- buttons.
0 = Equal sound Right and Left
R 7 = Right speaker only
L 7 = Left speaker only
After 5 seconds control reverts back to
volume control.
Equalizer (EQ):
Select the EQ mode by pressing the SEL button .
Adjust the EQ by pressing the VOL +/- buttons
to choose between the preset settings: Classic,
Rock, Pop, Flat or EQ OFF as indicated in the
display area.
After 5 seconds control reverts back to
volume control.
Loud:
To boost high and low tones at low volume
levels, press the
SEL button until “LOUD ON”
appears in the display. To deselect, press either
VOL +/- buttons and “LOUD OFF” will appear in
the display.
RV6100 General Operations (continued)
5
Cancelling the Sleep Timer:
1. Press the SLEEP button and SLEEP OFF will
appear in the display.
2. Wait 5 seconds and the display will return to
normal operation.
Headphone Operations:
Insert headphones into 3.5mm headphone jack
located on the front panel of the radio. The
speakers of the unit will automatically be muted.
BEEP ON/OFF:
To turn the unit's audible beep on or off, short
press the SEL button until BEEP ON or BEEP
OFF appears in the display. Use the VOL +/- but-
tons to make your selection.
CLOCK 12/24
To set the unit's clock to either a 12 or a 24 hour
format press SEL button until CLOCK 12 or
CLOCK 24 appears in the display. Use the
VOL +/- buttons to make your selection.
General Reset:
To reset the unit, press the reset button located
on the front of the radio using the tip of a ball
point pen. This is a general logic reset related to
button function, display and Bluetooth issues.
This reset may not clear all issues.
Hard Reset:
This reset will bring all functions back to factory
defaults. All programming, settings and memory
functions will be wiped.
1. Turn On radio.
2. Select the AUX IN 1 input.
3. Press and hold the
button until (about 5
seconds) the display shows “RESET” then release
it. The radio will turn off.
4. Push the power button to turn the radio back
on. Check that your issue is corrected.
Note: All memory settings will need to be re-input
(clock, station memory, tone settings etc.)
Sound Controls