Process Solutions Magma PCI Expansion Chassis PE3R Installation Instructions HWDOC-X279-en-A December 2014
© Honeywell International Sàrl 2014. All Rights Reserved. This document is the confidential and proprietary information of Honeywell. Reproduction and distribution of these materials without the express written consent of Honeywell is strictly forbidden.
Symbol definitions The following table lists the symbols used in this document to denote certain conditions. Symbol Definition NOTICE is used to address practices not related to physical injury. CAUTION indicates a hazardous situation that, if not avoided, could result in minor or moderate injury. CAUTION symbol on the equipment refers the user to the product manual for additional information. The symbol appears next to required information in the manual.
Table of contents About this guide ....................................................................................................................................................................................... 5 Chapter 1 1.1 Chapter 2 Introduction .................................................................................................................................................................. 6 Components ............................................................................
About this guide This document provides detailed information on how to use the Magma PCI Expansion Chassis with Honeywell-configured Dell servers. Revision history Revision Date Description A December 2013 Initial release of the document. B December 2014 Added support for DL 360 P Gen 8 Related documents The following list identifies publications that may contain information relevant to the information in this document.
Chapter 1 Introduction This document provides detailed information on how to use the Magma PCI Expansion Chassis with Honeywell-configured Dell servers. You must use this PCI Expansion chassis only if you are planning to interface Honeywell-configured Dell Power Edge 12G servers (T320 and R320) and 11G servers (T610, R710, T310 and HP DL 360 P Gen 8 Server) on ControlNet, using PCI based PCIC-02 Control Net interface card. These servers do not contain the inbuilt PCI slot.
Formatted Table Model/Part Number Description PEHIFX1 PCI Express host card with 1 meter interface cable standard length. SUBCBL1.5HF Interface Cable 1.5 meter. For more information about the Magma PCIE to PCI Expansion Chassis, see the PCI Expansion Chassis User's Guide and Host Card Installation Guide by Magma Inc. and supplied with the hardware. HWDOC-X279-en-A 7 www.honeywellprocess.
Chapter 2 2.1 Installation Installing the PCI Express host Before installing the PCI Express (PCIE) host, see the following topics in the PCI Expansion Chassis User's Guide and Host Card Installation Guide: Hardware Installation Verify Installation To install the PCIE host inside a server 1. Shut down the computer. 2. Remove the power cords from the rear end of the server and wait for 20 seconds. 3. Open the computer cover. 4.
Server Steps T310 and T610 servers Remove the expansion card stabilizer. Locate the Card retainers (Blue plastic expansion card retainer) as shown below. Unlock card retainers to release the Metal Shield (Card Slot Blank plate). Formatted: Font: (Default) Arial HWDOC-X279-en-A 9 www.honeywellprocess.
Server Steps R710 servers Pull out the clip to release the Metal Shield (Card Slot Blank plate). 1. HWDOC-X279-en-A Locate the Card retainer Clip (Blue plastic expansion card retainer) as shown below. 10 www.honeywellprocess.
Server Steps T320 servers Unlock card retainers to release the Metal Shield (Card Slot Blank plate). 2. Locate the Card retainers (Blue plastic expansion card retainer) as shown below. Field Code Changed HWDOC-X279-en-A 11 www.honeywellprocess.
Server Steps HP DL 360 P Gen 8 Server 1. On the Magma host card: a) Replace bracket for Magma host card with small factor bracket provided with kit. 2. On the HP DL360p server: a) Locate the blue tab and lift the blue latch up. b) To disengage the thumbscrew, turn the blue latch 180 degrees (counter clock-wise). c) Lift the PCI riser cage and remove it from the server. 3. HWDOC-X279-en-A 12 www.honeywellprocess.
Server Steps R320 servers Pull out the clip to release the Metal Shield (Card Slot Blank plate). 1. Locate the Card retainer Clip (Blue plastic expansion card retainer) as shown below in red circle Field Code Changed 6. Insert the Magma PCI Express Host card into the slot identified in step 4. 7. Close the card restrainer/clip that was removed in step 5. 8. Replace the computer cover. Notice! Do not connect the power cord to the computer. HWDOC-X279-en-A 13 www.honeywellprocess.
2.2 Installing the ControlNet card inside the Magma Expansion Chassis Notice! Ensure that the Magma Chassis is turned off. Before installing third party hardware cards inside the Magma Chassis, see the following sections in the PCI Expansion Chassis User's Guide and Host Card Installation Guide: Hardware Installation Verify Installation To install the ControlNet card inside the Magma Expansion Chassis 1. Open the Magma Chassis.
3. Tighten the thumbscrews at both end of the cable. HWDOC-X279-en-A 15 www.honeywellprocess.
Chapter 3 3.1 Operation of the Magma Expansion Chassis Turn on the server Before you turn on the server, be aware of the following: Turn on the Magma Expansion Chassis before you turn on the server. The Magma Expansion Chassis on and off switch is located on the front of the chassis, as well as the back panel. Turn on both switches and monitor the power status LED indicator. 3.2 Verify that the power status LED indicator is green (the Magma Expansion Chassis is on).
Notices Documentation feedback You can find the most up-to-date documents on the Honeywell Process Solutions support website at: http://www.honeywellprocess.com/support If you have comments about Honeywell Process Solutions documentation, send your feedback to: hpsdocs@honeywell.com Use this email address to provide feedback, or to report errors and omissions in the documentation.
Northern Europe Country Local Time Business Hours Phone Facsimile Email Denmark 07:00 – 18:00 80–252165 +45 6980 2349 hpscustomersupport@honeywell.com Finland 08:00 – 19:00 0800–9–15938 +358 (0)9 2319 4396 hpscustomersupport@honeywell.com Ireland 06:00 – 17:00 1800939488 +353 (0)1 686 4905 hpscustomersupport@honeywell.com Netherlands 07:00 – 18:00 0800 020 3498 +31 (0)20 524 1609 hpscustomersupport@honeywell.
Central Europe Country Local Time Business Hours Phone Facsimile Email Austria 07:00 – 18:00 0800 006438 +43 (0)1 253 6722 4904 hpscustomersupport@honeywell.com Germany 07:00 – 18:00 0800 7239098 +49 (0)30 6908 8463 hpscustomersupport@honeywell.com Greece 08:00 – 19:00 00800 12 9493 +30 21 1 268 6973 hpscustomersupport@honeywell.com Israel 08:00 – 19:00 1 809 407 309 +972 (0)2 591 6148 hpscustomersupport@honeywell.
Region Phone People’s Republic of China +86-21-2219-6888 Facsimile Email Global-TAC-China@honeywell.com 800-820-0237 400-820-0386 Singapore +65-6823-2215 Japan +65-6445-3033 GTAC-SEA@honeywell.com +81-3-6730-7228 Global-TACJapanJA25@honeywell.com World Wide Web Honeywell Process Solutions website: http://www.honeywellprocess.com/support Elsewhere Contact your nearest Honeywell office. HWDOC-X279-en-A 20 www.honeywellprocess.
For more information To learn more about Honeywell’s products or solutions visit www.honeywellprocess.com or contact your Honeywell account manager. Process Solutions Honeywell 1250 West Sam Houston Parkway South Houston, TX 77042 Honeywell House, Skimped Hill Lane Bracknell, RG12 1EB Shanghai City Centre, 100 Junyi Road Shanghai, China 20051 www.honeywellprocess.
