Instructions / Assembly

ManualsBrandsMagma ManualsSports & OutdoorsTrailmate Connoisseur Series Portable Propane Gas Barbecue Grill in Stainless Steel

Connoisseur Series Gas Grill

Model A10-801

OWNER’S MANUAL

For questions regarding performance, assembly,

operation, parts, or returns, contact the experts

at MAGMA by calling (562) 627-0500

7:00 a.m. - 5:00 p.m. Pacific Time Monday thru

Friday or e-mail us at mail@MagmaProducts.com

Read these instructions carefully before use. Familiarize yourself with the appliance before

connecting it to its gas container. Keep these instructions for future reference.

TrailMate

™

Summary of content (9 pages)

PAGE 1
OWNER’S MANUAL TrailMate ™ Connoisseur Series Gas Grill Model A10-801 For questions regarding performance, assembly, operation, parts, or returns, contact the experts at MAGMA by calling (562) 627-0500 7:00 a.m. - 5:00 p.m. Pacific Time Monday thru Friday or e-mail us at mail@MagmaProducts.com Read these instructions carefully before use. Familiarize yourself with the appliance before connecting it to its gas container. Keep these instructions for future reference.
PAGE 2
PAGE 3
MOUNT HARDWARE Fasteners are supplied for Single Mount grill mounting options. See Magma Catalog or Website for best mount selection. Single mount through-bolt applications 4 Carriage bolts, washers & lock nuts. Note: Place washers on carriage bolts as shown above.. Single mount non-through-bolt applications, including Style 1 “Levelock” 4 Hex head bolts & lock washers. Note: Place lock washers on hex bolts as shown above.
PAGE 4
OPERATING PROCEDURES OPERATE ONLY ON “LOW” WHEN LID IS CLOSED. ALWAYS OPERATE WITH GREASE TRAY IN PLACE. WARNING: Do not overheat grill. Magma Grills do not require pre-heating. Stainless Steel loses anti-corrosive characteristics when subjected to extreme heat. Most grilling is done on low temperature with the lid closed. If medium or high heat is required, grill with lid open. • • • • LIGHTING INSTRUCTIONS Open lid during lighting. Place flame up to burner through the match light hole.
PAGE 5
DISASSEMBLY & RE-ASSEMBLY A - Lift radiant plate up & out of left slot. B - Remove by sliding it out of right slot. C - Remove burner screw and remove burner. Check burner for grease residue or spider webs that may obstruct gas flow. CAUTION: WHEN REPLACING BURNER, CUT SLOTS IN BURNER MUST FACE DOWN. D - Lift the two-section liner out of outer shell by lifting up on the burner support bracket on the left liner section. (1) Slide the left section partially over the right section.
PAGE 6
MAINTENANCE Stainless Steel, contrary to popular belief, can rust. Most commonly, deposits on the surface of the product will trap moisture. It is this moisture that robs the stainless steel of oxygen. Oxygen is the element that reacts with the stainless steel to form a protective layer of chrome oxide. Robbed of oxygen this reaction does not take place and “crevice corrosion”, or “surface rusting”, occurs.
PAGE 7
USING GRILL WITH ON-BOARD LPG (PROPANE) SYSTEMS • Magma On-Board LPG (Propane) Valves and Hose Kits allow Magma Grills to be installed within a boats existing on-board, pre-regulated low pressure LPG (Propane) system. • Use only Magma Type 3 Low Pressure LPG (Propane) Valves. See our Valve Application Guide at www. MagmaProducts.com for correct valve. • In North America use Magma A10-225 LPG 10' Hose Kit in conjunction with Type 3 Valve.
PAGE 8
USING GRILL WITH ON-BOARD CNG (NATURAL GAS) SYSTEMS •For on-board CNG (Natural Gas) Systems, use Magma Type 4 X-Low Output - Low Pressure Natural Gas Control Valve. Check your local dealer for proper hose and fittings. TROUBLE SHOOTING GUIDE Problem Possible Cause Possible Solution Burner will not light with match No gas flow Check fuel level, replace canister or refill cylinder Obstructed gas flow Clean burner and valve orifice.
PAGE 9
Contents A x4 B x4 x4 x4 x4 A) Pack of (4) 1/4”-20 x 5/8” hex head screws and internal lock washers for “Levelock” single mount application. B) Pack of (4) 1/4”-20 x 5/8” carriage bolts, washers and lock nuts for dual mount and single mount applications and table legs. LIMITED WARRANTY Magma Products, Inc. guarantees this product to be free from defects in materials or workmanship to the original consumer.