OWNER’S MANUAL For Models: A10-104 • A10-114 Stainless Steel Charcoal Grill Patent & Patents Pending For questions regarding performance, assembly, operation, parts, or returns, contact the experts at MAGMA by calling (562) 627-0500 7:00 a.m. - 5:00 p.m. Pacific Time Monday thru Friday or e-mail us at mail@MagmaProducts.com Read these instructions carefully before use. Familiarize yourself with the appliance before using. Keep these instructions for future reference.
IMPORTANT SAFETY WARNINGS READ ALL INSTRUCTIONS BEFORE OPERATING. • WARNING! DO NOT USE INDOORS. • USE OUTDOORS ONLY. • DO NOT USE THIS APPLIANCE INSIDE THE BOAT OR ANY ENCLOSED SPACE. • GRILLS RADIATE HEAT. CLEARANCE FROM COMBUSTIBLES, 24” SIDES AND BACK. NEVER USE UNDER AWNINGS, PATIO COVERS, ETC. • WARNING! THIS GRILL WILL BECOME VERY HOT. DO NOT MOVE DURING USE. • NEVER LEAVE HOT GRILL UNATTENDED. • WARNING! DO NOT USE ALCOHOL, GASOLINE OR OTHER SIMILAR LIQUIDS TO LIGHT OR REACTIVATE THE FIRE.
ATTACH THE LID TO THE BOWL 1 2 3 GRATE ASSEMBLY 1 2 3 3
“L” BRACKET & CLAMP ASSEMBLY SETTING UP YOUR GRILL Mounts sold separately. VisitAdjust our website www.MagmaProducts.com for mounting options. and tighten with wrenches horizontally for permanent attachment. CAUTION: Do not disassemble here when stowing. Level Flat Surface 1 2 3 4 1 Select and install appropriate Magma mount in your desired location. Prior to installing the grill, check that mount does not easily move with a reasonable force applied. 2 Slide L-Bracket & Clamp on to mount knurled rod.
ADJUSTING GRILL TO WIND CONDITIONS 6 5 6a 7 8 7a 5 Remove cooking grill grate 6 With grill body tightly attached to L-Bracket, unthread lower charcoal grill nut 3 full revolutions. (6a) Lift entire grill up to disengage from stud positioning pins. 7 Rotate so lid operates freely in the desired position. (7a) Carefully lower back down, making sure pins are re-engaged and rethread the “nut” 3 revolutions until tight. If the nut does not turn 3 revolutions the pins are not engaged properly.
OPERATING PROCEDURES GETTING READY TO COOK A • Position grill lid to block the wind. See page 5. • Remove cooking grill A , by unscrewing it from threaded center post. • Fill Magma “Charcoal Starter” (#A10-150) with briquets, or stack two handfuls away from the center post, then soak the briquets with lighter fluid per can instructions. • Wait one minute before igniting. Then, preferably, use a long nozzle butane lighter to light the briquets.
MAINTENANCE Stainless steel contrary to popular belief can rust. Most commonly, deposits on surface of the product will trap moisture. It is this moisture that robs stainless steel of oxygen. Oxygen is the element that reacts with stainless steel to form a protective layer of chrome oxide. Robbed of oxygen, this reaction does not take place and “crevice corrosion” or “surface rusting” occurs. To minimize this effect, thoroughly clean your grill with soap and water, rinse with fresh water, and dry.
REPLACEMENT PARTS A10-104 A10-114 10-040 Cooking Grill 10-441 Cooking Grill Marine Kettle 2 Charcoal Original Size Marine Kettle 2 Charcoal Party Size 10-050 Lower Grill & Nut 10-442 Lower Grill & Nut 10-055 Lower Grill Spacer 10-455 Lower Grill Spacer 10-751 Complete Handle Assembly & Fasteners 10-751 Complete Handle Assembly & Fasteners 10-031 Draft Door Assembly 10-431 Draft Door Assembly 10-403 Lid Assembly with Hinge & Fasteners 10-463 Bowl Assembly 10-101 Lid Assembly with Hinge & Fasten
ACCESSORIES 10 Piece “Nesting” 18-10 Mirror Polished Stainless Steel Gourmet Cookware 7 Piece “Nesting” 18-10 Mirror Polished Stainless Steel Gourmet Cookware Starter Set Fish & Veggie Grill Tray Stainless Steel Finish or Coated with DuPont® Teflon® Select Non-Stick Coating Telescoping Grill Tools and Storage/Carrying Case 5 Piece Set, Grill Brush, Tongs, Fork, Spatula and Storage Case Stores in less than 1/2 cubic foot Stores in less than 1/2 cubic foot 10 Piece “Nesting” Mirror Polished Stainless S
MOUNTS Round Rail Mount Side (Bulkhead) or Square/Flat Rail Mount POW’R GRIP™ Fish Rod Holder Mount Socket Type Rod Holder Mount Fits Tempress Fish-On® & Roberts Rod Holder Sockets Surface Deck Socket Mount Flush Deck Socket Mount Socket Type Rod Holder Mount Double Locking “Stowable” Pedestal Mount 28" (71cn) Shore Stand/ Table Top Legs Fits Scotty®/Striker Grip Rod Holder Sockets Mounting Extension LIMITED WARRANTY 83-205 0510 83-104 Magma Products, Products, Inc. Magma Inc.
