Model #: __________________________ Serial #: __________________________ Date Purchased: ___________________ Installation & Operation Manual MKH24, MKH36, MKH48, MKH60 & MKH72 All Options C E E S I G N D D CERT I F I ED E R T I F I L25-053 Rev.
TO THE PURCHASER, OWNER AND STORE MANAGER Please review these warnings prior to posting them in a prominent location for reference. TO THE PURCHASER WARNING Post in a prominent location the instructions to be followed in the event that an operator smells gas. Obtain this information from your local gas supplier.
Table of Contents MKH Series Gas Griddle 1. INSTALLATION SECTION.......................................................................................4 1.1. 1.2. 1.3. 1.4. CHECKING YOUR NEW GRIDDLE .................................................................................................... 4 ELECTRICAL CONNECTION(S) ........................................................................................................ 4 INSTALLATION CLEARANCES ...................................................
Installation MKH Series Gas Griddle 1. Installation Section 1.1. Checking Your New Griddle Your new griddle has been carefully packed into one crate. Every effort has been made to ensure that your new griddle is delivered to you in perfect condition. As you unpack your new appliance, inspect each of the pieces for damage. If something is damaged, Contact the shipper immediately; the shipper is only responsible for 15 days after delivery.
Installation MKH Series Gas Griddle 1.3. Installation Clearances Your new MagiKitch’n Griddle needs clearance around it for proper operation. Adequate clearances allow for servicing and proper burner operation. The clearances shown below are for installation in combustible and non-combustible construction. The appliance can be serviced from the front of the unit, however it may need to be pulled away from the wall for access to the gas supply and electrical supply connections.
Installation MKH Series Gas Griddle 1.6. Installation Setup The installation of this appliance MUST conform to local codes. In the absence of local codes The gas line must be installed to meet the local building codes or National Fuel Gas Code ANSI Z223.1/ NFPA 54 Latest Edition, or the Natural Gas and Propane Installation Code, CSA-B149.1 as applicable, and local codes. To Start uncrate appliance and locate installation accessories. 1.6.1.
Installation MKH Series Gas Griddle NOTICE Larger models have 6 threaded receiving holes, but require only the four 1/2" bolts on each corner to mount the griddle. 1. Remove (4) existing 1/4-20 nuts and bolts from the rear corners of the equipment stand. 2. Align the 2 bolt holes on the rear corners of the stand with the 2 bolt holes on the rear mounting brackets. Orient the brackets as shown in Figure #4 on this page. 3.
Installation MKH Series Gas Griddle 1.7. Final Gas Connection A properly installed gas supply system will deliver adequate pressure (7 to 8 inches w.c. for natural gas, 11 to 12 inches w.c. for propane) to all appliances connected to the line, operating at full demand. 1.7.1. Regulator Assembly An adequate gas supply is important for the appliance to operate properly. Undersized lines or lowpressures will restrict the volume of gas required for satisfactory performance.
Operations MKH Series Gas Griddle 2. Operation Section Ensure that a proper installation has been performed on the appliance and that all warnings, cautions, and notices contained in this manual have been read, understood and adhered to before proceeding. 2.1. Lighting Instructions 2.1.1. Solid State Thermostat Appliance 1. Turn all thermostat knobs to the “OFF” position, or the lowest possible temperature setting. 2.
Operations MKH Series Gas Griddle Seasoning is not required on a Chrome Plated Cooking surface, but the following procedure may be performed to improve the non-stick qualities of the chrome plated cooking surface. 2.2.1. Griddle Surface Seasoning 1. To season the griddle, Light all pilots and turn all the thermostat controls to 200°F. As the unit heats up to 200°F, apply a light film of cooking oil or beef suet over the entire cooking surface, wiping off any excess build up.
Calibration MKH Series Gas Griddle 3. Thermostat Calibration Section Each control typically operates a pair of burners with a Snap action, Electric or Solid State. The controls were set at the factory. However, if the griddle’s surface temperature varies greatly from the setting on the thermostat knob, adjust the thermostat using the following procedure: 3.1.
Basic Operation MKH Series Gas Griddle 4. Basic Operation 4.1. Operational Helpful Hints 1. Each thermostat controls 12" of griddle surface, whenever possible, use the leftmost or rightmost thermostats for the lowest cooking temperatures. The adjacent thermostats set at higher temperatures will effect centrally located thermostats. 2. For quicker thermostat response during heavy loading of the griddle, load product directly over the thermostat sensing probe.
Cleaning & Maintenance MKH Series Gas Griddle 5. Cleaning & Maintenance Section 5.1. Griddle Surface Cleaning, During Operation Hours 1. Keep the griddle surface clean to prevent sticking and poor food product quality. 2. Scrape the griddle plate regularly through out the day with a scraper intended for your type of griddle surfaces to remove all surface grease and food debris. NOTICE Do not use Grill Bricks, Grill Screens, or any other type of abrasive material on your MagiKitch'n Chrome Griddle Surface.
Cleaning & Maintenance MKH Series Gas Griddle ü ü ü ü ü ü ü Visually check the appearance of the main burners, all burners should have a nice blue flame. Make sure that all gas connections have not been tampered with or damaged, check for leaks with a soapy water solution. Never use an open flame to check for leaks. Check to see that the flue exhaust area has no food debris, or blocked in any way. Never allow the flue to become excessively dirty.
Trouble Shooting MKH Series Gas Griddle 5.6. Trouble Shooting Charts The following charts may help to eliminate any basic operational problems that you may be experiencing with your appliance. Locate the problem on the left side of the chart, and cross-reference with the possible cause. Once the problem has been identified take the appropriate action to rectify the problem. 5.6.1.
Accessories MKH Series Gas Griddle 6. Accessories 6.1. Standard All plain steel and chrome plated griddles are shipped with a set of 4” adjustable legs. The appliance also comes equipped from the factory with a manual gas shutoff valve, and the specified gas regulator for the model and gas type purchased. Each MKG Chrome surfaced griddle is equipped with a Chrome Kit which includes a cleaning brush, cleaning powder, spatula, scraper, and scraper blade replacements.
Accessories MKH Series Gas Griddle WORKSHELVES WITH AND WITHOUT TOWEL BARS TOWEL BAR ONLY PAN CUTOUTS AND CUTTING BOARDS ARE AVAILABLE ON LARGER WORKSHELVES 6.2.2. Cutting Boards Size 8" X 12" Cutting Board 8" X 24" Cutting Board 8" X 48" Cutting Board 8" X 72" Cutting Board Part No. 1604-0643600-C 1604-0643700-C 1604-0643800-C 1604-0643900-C Other sizes are available, consult factory for size, price, and availability. L25-053 Rev.
Accessories MKH Series Gas Griddle 6.2.3. Warming Shelves, Rear Shelf Model C/A, Shelf Rear MKG24 C/A, Shelf Rear MKG36 C/A, Shelf Rear MKG48 C/A, Shelf Rear MKG60 C/A, Shelf Rear MKG72 Part No. 5225-1535701-C 5225-1535702-C 5225-1535703-C 5225-1535704-C 5225-1535705-C Shelf Kits can be attached to existing models. The Stainless Steel shelf is removable from the shelf framework for easier cleaning if necessary. REMOVABLE SHELF EXISTING BOLTS ON APPLIANCE 18 L25-053 Rev.
Accessories MKH Series Gas Griddle 6.2.4. Equipment Stands Equipment stands can be ordered with legs or casters (stands with casters shipped after May 2006 are equipped with adjustable casters). NOTE: It should also be noted that when ordering an equipment stand for your MKG appliance, you will also need to order and MKG Joining Kit, Part No. 7225-1512101.
Accessories MKH Series Gas Griddle 6.2.5. Miscellaneous Your appliance can also be used with the following miscellaneous accessories so you can customize your operation to your specific demands.. The wall spacers listed below insure that you cannot push the appliance too close to the rear wall. The Utensil box gives you a handy location to store your cooking tools. The Utensil box does not interfere with any controls, and can be moved from one end of the griddle to the other without the use of tools.
Notes MKH Series Gas Griddle 7. Notes Page L25-053 Rev.
In the event of problems with or questions about your order, please contact the MagiKitch’n factory at: PH- (603) 225-6684 World Wide Website- www.magikitchn.com In the event of problems with or questions about your equipment, please contact the MagiKitch’n Authorized Service and Parts representative (ASAP) covering your area, or contact Pitco at the numbers listed to the left. MAILING ADDRESS – P.O. BOX 501, CONCORD, NH 03302-0501 SHIPPING ADDRESS – 10 FERRY ST., CONCORD, NH 03301 L25-053 Rev.
