Model #: ___________________________ Serial #: ___________________________ Date Purchased: ___________________ Installation & Operation Manual MKG24, MKG36, MKG48, MKG60 & MKG72 All Options C E E S I G N D D CERT I F I ED E R T I F I L25-055 Rev.
TO THE PURCHASER, OWNER AND STORE MANAGER Please review these warnings prior to posting them in a prominent location for reference. TO THE PURCHASER Post in a prominent location the instructions to be followeed in the event that an operator smells gas. Obtain this information from your local gas supplier. WARNING DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Do not spray aerosols in the vicinity of this appliance when it is in operation.
Table of Contents MKG Series Gas Griddle 1. INSTALLATION ....................................................................................................... 4 1.1. CHECKING YOUR NEW GRIDDLE .................................................................................................... 4 ELECTRICAL CONNECTION(S) .................................................................................................................. 4 1.3. INSTALLATION CLEARANCES...........................................
Installation MKG Series Gas Griddle 1. Installation 1.1. Checking Your New Griddle Your new MagiKitch’n appliance has been carefully packed into one crate. Every effort has been made to ensure that it is delivered to you in perfect condition. As you unpack your new appliance, inspect each of the pieces for damage. If something is damaged, DO NOT sign the bill of lading. Contact the shipper immediately; the shipper is only responsible for 15 days after delivery.
Installation MKG Series Gas Griddle 1.3. Installation Clearances Your new MagiKitch’n Griddle needs clearance around it for proper operation. Adequate clearances allow for servicing and proper burner operation. The clearances shown below are for installation in combustible and non-combustible construction. The appliance can be serviced from the front of the unit, however it may need to be pulled away from the wall for access to the gas supply and electrical supply connections.
Installation MKG Series Gas Griddle Pleasant Valley Rd., Cleveland, OH 44131. In Australia, the ventilation system must comply with AS/NZS 5601.1. CAUTION Excessive ventilation causes drafts, which will interfere with the operation of the appliance. Leave at least 18 inches of open space between the flue opening and the intake of the exhaust hood. CAUTION Ensure that your ventilation system does not cause a down draft at the appliance’s flue opening.
Installation MKG Series Gas Griddle 1.6.3. Equipment Stand ATTENTION Rear mounting brackets should be installed to the Equipment Stand prior to placing griddle on the stand. IMPORTANT Install the griddle so that the locking casters are at the front of the unit. The casters should be LOCKED before the unit is placed into operation. (See Figure 4). To mount the griddle to the stand, locate joining kit supplied with stand.
Installation MKG Series Gas Griddle 1.6.4. Leveling Instructions NOTICE Equipment stands are shipped from the factory with the legs or casters set to the minimum height adjustment. Units should be leveled at time of installation, failure to do so could cause the griddle to operate improperly. 1. Identify the corner of the stand that needs to be adjusted, remove the weight load from the corner to be leveled. 2.
Installation MKG Series Gas Griddle 3. 4. 5. 6. 7. regulator, see Figure 6 & 6a. To check the supply pressure to the appliance use the pressure test point supplied on the manual shut off valve, also see Figure 6 & 6a. Use pipe joint compound that is suitable for use with LP gas on all threaded connections. Turn off all thermostats. Turn on gas supply and check all connections for leaks using ONLY a leak checking fluid or soapy water. NEVER use an open flame to check for gas leaks.
Operations MKG Series Gas Griddle LU FR BE DE NL BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT, LU, MT, NL, PL, PT, RO, ES, SI, SK, TR AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE, IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE, TR LU FR BE DE NL BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT, LU, MT, NL, PL, PT, RO, ES, SI, SK, TR AT, BG, CH, CZ, DK, EE, FI, GB, GR, HU, IE, IT, LT, LV, NO, PL, PT, RO, ES, SI, SK, SE, TR LU FR BE DE NL BG, CH, CY, CZ, FR, DE, GB, GR, HU, IE, IT, LU, MT, NL, PL, PT, RO, ES, SI, SK, TR A
Operations MKG Series Gas Griddle 2. Operation Ensure that a proper installation has been performed on the appliance and that all warnings, cautions, and notices contained in this manual have been read, understood and adhered to before proceeding. 2.1. Lighting Instructions 2.1.1. Snap-Action Thermostat Appliances 1. Turn all thermostat knobs to the “OFF” RIGHT PIEZO IGNITOR position. LEFT PIEZO IGNITOR 2.
Operations MKG Series Gas Griddle CAUTION If Pilot Ready light(s) does not illuminate, Turn all Thermostat "I/O" switches for that pilot to “O”(OFF), wait five minutes before attempting to re-light. WARNING If the gas supply and/or the electrical power is interrupted, or if pilot(s) extinguish, turn the thermostat knobs and the gas shut off valve to the "OFF" position and wait five (5) minutes before attempting to re-light the pilot. Do not attempt to operate this appliance during a power failure. 2.2.
Calibration MKG Series Gas Griddle 3. Thermostat Calibration Section Each control typically operates a pair of burners with a Snap action, Electric or Solid State. The controls were set at the factory. However, if the griddle’s surface temperature varies greatly from the setting on the thermostat knob, adjust the thermostat using the following procedure: 3.1. Snap Action and Electric Thermostat 1 Light pilots as described in section(s) 2.1.1 and THERMOSTAT ADJUSTMENT SCREW 2.1.2.
Basic Operation MKG Series Gas Griddle 4. Basic Operation 4.1. Operational Helpful Hints 1. Each thermostat controls 12" (30.5cm) of griddle surface, whenever possible, use the leftmost or rightmost thermostats for the lowest cooking temperatures. The adjacent thermostats set at higher temperatures will effect centrally located thermostats. 2. For quicker thermostat response during heavy loading of the griddle, load product directly over the thermostat sensing probe.
Cleaning & Maintenance MKG Series Gas Griddle 5. Cleaning & Maintenance Section 5.1. Griddle Surface Cleaning, During Operation Hours 1. Keep the griddle surface clean to prevent sticking and poor food product quality. 2. Scrape the griddle plate regularly through out the day with a scraper intended for your type of griddle surfaces to remove all surface grease and food debris. NOTICE Do not use Grill Bricks, Grill Screens, or any other type of abrasive material on your MagiKitch'n Chrome Griddle Surface.
Cleaning & Maintenance MKG Series Gas Griddle Make sure that all gas connections have not been tampered with or damaged, check for leaks with a soapy water solution. Never use an open flame to check for leaks. Check to see that the flue exhaust area has no food debris, or blocked in any way. Never allow the flue to become excessively dirty. The flue being free of obstruction is imperative to proper burner operation.
Trouble Shooting MKG Series Gas Griddle 5.6. Trouble Shooting Charts The following charts may help to eliminate any basic operational problems that you may be experiencing with your appliance. Locate the problem on the left side of the chart, and cross-reference with the possible cause. Once the problem has been identified take the appropriate action to rectify the problem. 5.6.1.
Accessories MKG Series Gas Griddle 6. Accessories 6.1. Standard All plain steel and chrome plated griddles are shipped with a set of 4” (10cm) adjustable legs. The appliance also comes equipped from the factory with a manual gas shutoff valve, and the specified gas regulator for the model and gas type purchased. Each MKG Chrome surfaced griddle is equipped with a Chrome Kit which includes a cleaning brush, cleaning powder, spatula, scraper, and scraper blade replacements.
Accessories MKG Series Gas Griddle WORKSHELVES WITH AND WITHOUT TOWEL BARS TOWEL BAR ONLY PAN CUTOUTS AND CUTTING BOARDS ARE AVAILABLE ON LARGER WORKSHELVES 6.2.2. Cutting Boards Size 8" X 12" (20.3 cm X 30.5 cm) Cutting Board 8" X 12" (20.3 cm X 61.0 cm) Cutting Board 8" X 12" (20.3 cm X 122.0 cm) Cutting Board 8" X 12" (20.3 cm X 183.0 cm) Cutting Board Part No. 1604-0643600-C 1604-0643700-C 1604-0643800-C 1604-0643900-C Other sizes are available, consult factory for size, price, and availability.
Accessories MKG Series Gas Griddle 6.2.3. Warming Shelves, Rear Shelf Model C/A, Shelf Rear MKG24 C/A, Shelf Rear MKG36 C/A, Shelf Rear MKG48 C/A, Shelf Rear MKG60 C/A, Shelf Rear MKG72 Part No. 5225-1535701-C 5225-1535702-C 5225-1535703-C 5225-1535704-C 5225-1535705-C Shelf Kits can be attached to existing models. The Stainless Steel shelf is removable from the shelf framework for easier cleaning if necessary. REMOVABLE SHELF EXISTING BOLTS ON APPLIANCE 20 L25-055 Rev.
Accessories MKG Series Gas Griddle 6.2.4. Equipment Stands Equipment stands can be ordered with legs or casters (stands with casters shipped after May 2006 are equipped with adjustable casters). NOTE: It should also be noted that when ordering an equipment stand for your MKG appliance, you will also need to order and MKG Joining Kit, Part No. 7225-1512101.
Accessories MKG Series Gas Griddle 6.2.5. Miscellaneous Your appliance can also be used with the following miscellaneous accessories so you can customize your operation to your specific demands.. The wall spacers listed below insure that you cannot push the appliance too close to the rear wall. The Utensil box gives you a handy location to store your cooking tools. The Utensil box does not interfere with any controls, and can be moved from one end of the griddle to the other without the use of tools.
In the event of problems with or questions about your order, please contact the MagiKitch’n factory at: PH- (603) 225-6684 World Wide Website- www.magikitchn.com In the event of problems with or questions about your equipment, please contact the MagiKitch’n Authorized Service and Parts representative (ASAP) covering your area, or contact Pitco at the numbers listed to the left. MAILING ADDRESS – P.O. BOX 501, CONCORD, NH 03302-0501 SHIPPING ADDRESS – 10 FERRY ST., CONCORD, NH 03301 L25-055 Rev.
